Thank you also for following our channel and for sharing our videos. See also this: kzfaq.info/get/bejne/o8qgZLKiz7rRpGw.html

Busco o eccion electrica de maquina de coser paff

Gracias por ver y compartir nuestros videos. kzfaq.info/get/bejne/aLedisl5tL-XY5s.html

Gracias también comparte nuestro video 👍

👍 next: kzfaq.info/get/bejne/auBmgKZyt5ico3k.html

Thank you 👉 kzfaq.info/get/bejne/aLedisl5tL-XY5s.html

@Dean Douglas...It is a small oiler from old Bernina sewing machines. www.ebay.com/sch/mastermann2013/m.html

I don't know which sewing machine it is, if it's a timing belt you might have a problem buying it, it's probably some old sewing machine.

Watch the video on the attached link; kzfaq.info/get/bejne/h8tnftSfx53KeIU.html

La Pfaff hobby 740 es una maquina de coser completamente diferente, ese video no lo tengo, recomiendo quitarle las tapas superior y laterales y veras como se sale el motor, la maquina DEBE estar desenchufada.

The Pfaff 269 is very rare for me, it is like an industrial model, it is a Pfaff 260 with the fact that it is on an industrial stand and with a large motor for industrial sewing machines. A good craftsman can do almost anything, it should look like this: www.pinterest.com/pin/375206212718607553

If the needle moves a little left to right then the bracket is not stuck, you may be wrong in the program settings, watch this video: kzfaq.info/get/bejne/np96eK6il565YnU.html

@@MasinskiKutak Thank you very much! I discovered that the spring that operates on top of the embroidery is kinda loose (after 60 years since the machine was made), so its not tensioned enough and i get a small zig zag also i do straight stitching.

Yes, I think it is too complicated a transformation, it is my opinion that you abandon such an idea. One of the items is this: kzfaq.info/get/bejne/o8qgZLKiz7rRpGw.html .

@@MasinskiKutak My suspicions were such...but being a crazy person, I've concocted much more elaborate schemes. Far too many times, I'm afraid. Thanks for your input...keep up the good work!!

I don't have that video, I have a service manual that you might find useful: www.masinskikutak.com/2021/11/pfaff-service-manual-adjustment-vintage.html

Esta máquina puede usar una aguja doble, zig zag en 3 puntos creo que no puede funcionar. kzfaq.info/get/bejne/np96eK6il565YnU.html

kzfaq.info/get/bejne/grGAlKSIzJmUYGQ.html

Synthetic ointment is recommended, which I used at the time I don't remember.

Hi Dammit J. 🙂 You didn't pay much, so you can learn a little and repair sewing machines, you didn't state which model you bought, there are small differences ...? but it doesn't matter, what you say that the lever for moving back and forth "froze" is most likely due to prolonged standing the fat has dried and burned on one of the moving parts (reversing assembly), put back the lever you took off, remove the top cover, remove the side cover (if any), loosen the belt on the engine and remove it and then heat the whole assembly strongly, a good hair dryer can also serve, use the lever back and forth with not too strong force (it can break), attached the following links: PFAFF 260 / PFAFF 262 / PFAFF 360 / PFAFF 362 Cataloc Parts / Pfaff Parts Diagram: kzfaq.info/get/bejne/oqqWlauG16ymeHU.html . Service Manual Pfaff 260 / Pfaff 262 / Pfaff 360 / Pfaff 362 : kzfaq.info/get/bejne/h8tnftSfx53KeIU.html .

Thank you so very much. I bought a pfaff 360. I will try your suggestions. I am appreciative.

@@dammitjanet4441 OK. See This image, the suspicious location is marked with a blue arrow, I hope you understand the image: www.pinterest.com/pin/375206212716000153/

Thank you. The picture is very helpful. I have a heat gun I might try. Your catalog parts video for the Pfaff 360 is especially helpful. I was elated to have access to that info.

@@dammitjanet4441 Feel free to heat everything that is metal, be careful the upper part of the machine has one plastic gear, high temperature could damage it .! So while warming up lightly try to move the lever back and forth, not too hard, it can break, moderate force.! The Pfaff parts catalog is great, especially for novice masters. kzfaq.info/get/bejne/oqqWlauG16ymeHU.html

No I do not have.

Bu Pfaff 261'a çok benziyor.?

Çağanoz yatağı kaymış oynamış iğne kırıyor Türkçe dublaj olarak video anlatımı nasıl yapılır tarifi

OK, the zig zag does not work, and can the machine do decorative stitches? kzfaq.info/get/bejne/h8tnftSfx53KeIU.html

Yes, you noticed that well this of the sewing machine was in excellent condition (mint)

@kl6990 Certainly, it is not as complicated as it seems, don't be afraid, only the brave win. 😃 ✌️ Of course you do it at your own risk.

@@MasinskiKutak The Main Problem is the Reverse Trigger, because he has no Function.I pulled too hard and often and now the Pieces are not on the right Place. Do i must repair it from above or from downside?The Motor are still dissambled but how can fit this Problem without Place at this small Whole?

With this model, the motor is in a plastic housing and it is impossible for dirt to enter the motor, it is not bad to remove it if you are doing a little major overhaul of the machine, I don't think it is necessary for this type of work.

@@MasinskiKutak for Pfaff 332 model do you recommend it’s removal before embarking on maintenance because it is likely to be soiled !

The Pfaff 332 has a partially open motor, if you think it might get dirty then remove the motor from the machine. Pfaff service manual: www.masinskikutak.com/2021/11/pfaff-service-manual-adjustment-vintage.html

I do not know the dimensions but I know that the Pfaff 360 coil also fits to the following machines: PFAFF 130, 230, 260, 262, 332, 360, 362PFAFF 1196, 1197, 1209, 1211, 1212, 1213, 1214, 1216, 1217, 1222, 1229..

These Pfaff models use a class "L" bobbin measured 20x8.8mm. Class *L* bobbins can be used in many class 15 cases but class 15 can't be used in the Pfaff L class due to the slight height differences.

Creo que entiendo tu pregunta, el gancho giratorio consta de una parte fija y una parte giratoria, tienes que quitar la parte fija, quitando el anillo de seguridad que está en la parte giratoria. Es necesario desatornillar un par de tornillos muy pequeños, se puede encontrar una imagen en este catálogo de piezas: kzfaq.info/get/bejne/oqqWlauG16ymeHU.html

Not vaseline grease, No way, use synthetic grease, it can be bought in a small package today and is suitable for lubricating plastic gears on sewing machines as well as during machine restoration. kzfaq.info/get/bejne/qt5ijNaK3rqvmnk.html

the "clutch on the side wheel" needs to be removed, cleaned and lubricated, it is not difficult; "the machine does not sew backwards", this is a more complex problem and for repair I would have to have a detailed insight into the sewing machine. kzfaq.info/get/bejne/auBmgKZyt5ico3k.html

@@MasinskiKutak Thank you!

I don't understand the question, 3:20 instead of wire springs can be leaf springs. kzfaq.info/get/bejne/o8qgZLKiz7rRpGw.htmlsi=zgDL7USxxfI_rmhR

Nic specjalnego, jest to najczęstszy środek smarny do łożysk, używaj go umiarkowanie.

Necesito saber como armo la cajabobina u el gancho de paff 260

Howdy "neighbo" 😃 you can send, i will reply as far as i can see in the pictures

It is a very complex mechanism, you have to lubricate the machine very thoroughly, if the lubrication does not produce a result then the only solution is to have it serviced by a good master. kzfaq.info/get/bejne/auBmgKZyt5ico3k.html

Preciso das correias da antiga PFAFF 360 automátic a do motor alguém sabe como posso conseguir? Quero original de alguém tiver por favor mande foto e entre em contato e passe o valor por favor e tbm do calcador pra pregar elástico e franzir e fazer

Maybe this video can help you: kzfaq.info/get/bejne/np96eK6il565YnU.html

@@MasinskiKutak Excellent thank you God bless your

kzfaq.info/get/bejne/np96eK6il565YnU.html

You bought a machine that probably hasn't been used and maintained for a long time, the specified spring is nothing special, I don't know if I have the specified spring in the workshop and I don't even know its exact length. The zigzag stitch width regulator has nothing to do with the spring, it would have to move even without the spring, try pulling the position where the spring is with your right hand and start the zigzag stitch width regulator with the other hand.? For you, I recommend another video of the Pfaff 230, which is much closer to your model, the only difference is that your model is "free arm" and this is a classic flat work surface, see: kzfaq.info/get/bejne/aLedisl5tL-XY5s.html

@@MasinskiKutak thanks. But may I know the purpose of this spring and why is it hooked to the embroidery assembly unit?

The purpose of the spring is to pull the part it is attached to.

Bisa beli online, kebanyakan dijual di Jerman dan Turki, ada juga yang ganti ban, perlu diingat harganya lumayan mahal, saya tidak punya ikat pinggang itu.

Mereka mempunyai dua ikat pinggang, satu ikat pinggang di motor dan ikat pinggang lainnya di dalam mesin jahit, yang putus di tempat anda, ini sangat penting.!!

You have a problem with sewing machine timing, Of course you can waste time, this rarely happens, look at the condition of your sewing machine timing belt .

The question is very general, You must try to explain your problem in a little more detail.

Pfaff 332 имеет два ремня, один на двигателе, а другой ремень ГРМ, который вам нужен. Смотрите эту тему по адресу: www.masinskikutak.com/2021/12/pfaff-timing-belt-pfaff-motor-cord-belt.html

I don't know, my specialty is sewing machines.

هذه ماكينة خياطة قديمة، ولا تزال تحظى بشعبية كبيرة في جميع أنحاء العالم اليوم، ولم تعد آلات الخياطة بهذه الجودة تنتج.

@@MasinskiKutak فعلا كلامك صحيح مئة بالمئة

I don't know what you're interested in, ?? this video is not applicable to on Pfaff 285, it is a completely different performance.