I have a 2014 500 just like yours. Only problem I’ve had is new timing chain at 3,000 miles. And a stick coming up through the floor as well. Great little machine for the money. Love it!!!!

Your Tractor Supply dealer will tell you where to trailer you Massimo for servie. Next year that is what I will do. This year I changed the oil, filter, topped up all the fluids. I had to change the spark plug last year so when you do change the oil, change the plug. I removed the rubber closures on the doors. No point. I got stuck in deep mud once but used the winch to get out. Overall worth every cent---so far. Still trying to figure out how to change the air filter and check the gear oil. Maybe tomorrow. BTW, keep the battery on a trickle charger at all times while the beast is at rest.

You can remove the seat side bars very easily… that’s what I did. As for the difficulty shifting into L. I had the same issue. You can adjust the shift linkage to correct this. Some people have issues shifting into R. You have to depress the break pedal firmly as it is cabled to a pin that retracts to allow a smooth shift into R.

Since I don’t expect a Cadillac when I buy cheap, I am completely satisfied with mine! The $6000 I saved I spent on my off road Jeep which has pull Humvees out!

You've got to follow the manufacturer's break in and maintenance schedule on these things very closely. If you do this, it'll perform well and last for a good while.

I agree with two solutions mentioned here. I just bought a new Axis 500 in late May 2022. One issue quickly popped up. I had trouble getting it into reverse. I played around a little and found I needed to just increase my foot pressure on the brake. If I pulled down into reverse where it would stop before going into reverse, I could feel it release as I increased pressure and it would easily go into reverse. I hear there is actually a cable that needs to pull a pin to allow the drop into reverse. That makes sense. If I run into this problem again, I will look to see if there is an adjustment for the cable. Next is a common complaint about the door latches being sticky. This one is a no-brainer. The problem is metal to metal friction. When I first got my vehicle the door closed easily. After just a couple of weeks the driver's door would bounce off the latch rather than latch. It seemed like an adjustment, but that didn't help. I then grabbed a can of Liquid Wrench and shot the mechanism inside and out. I wiped off the excess to clean things up and !BINGO! I have doors that close very easily. My only complaint is that it steer worse than my '49 1 ton truck. I am looking at installing an aftermarket Electric Power Steering unit.😊😊

so far every thing you said as a con about it is general maintenance .. those door latches will do alot better with a little oiling, the same with the transmission linkage ,,, now the rear being posi track . is what it is ,, im sure theres been a few times it also helped you to have that .. and the floor pan, well thats a factory con for sure ,,, all they had to do is put a small plate where most peoples feet lay on the floor to take out the sagging movement and the floor would still be fine .... i think the things you would like for your father is more in line with a golf cart type machine ,,, they are smoother riding,, easier to get in ,,and made so they dont tear up the grass ,,, there are models of golf carts that have small beds on the back too ... all in all for the price and the time you put on it your doing good

Thanks for taking your time to post this video. Similar to many people viewing your video, I am looking to get the best machine for the money but am admittedly cautious about Chinese made machines. Yes, I’m aware that the company has a large and nice looking plant in Texas, but that alone doesn’t assure quality. Hopefully this proves to be a nice and durable product!

I'm about to pull the trigger on the one at lowes. I have 32 acres that includes two hollers and two knobs. About 26 acres of it is woods. The big trees were taken out about 8 years ago and they made some rough "logging roads" to get to the trees. They are just waiting for me to start using one of these on them. I just need it to get around the property and bring my wife to the far corners. She'll not really join me most places in the woods because it's a lot of walking and uphills. My 4x4 pickup is also just too much for it. I can bring this up with my weedeater and chainsaw and really get stuff cleaned up. And we can log it again to more than pay for this thing. :) I just hope it really holds up. I've seen it parked outside Lowe's all the time and just assumed it was a toy and not a "real" UTV. But apparently it is.

Adjust the shifter linkage under the engine cover and it will go in gear easier, and you can buy the door pieces for little money, I just bought one of these under the Axis name and so far like it

Nice review.. Your critiques are noted and make me buying one easier and known flaws are nice.. Just purchased today.. Dump bed crush hand is common sense issue..I could see me getting jammed up on a bad day tho..thx 4 heads up.. The door latch and handle need grease regularly...yours is dry.. it's not an expensive latch assembly so expect some manual interference... The gear shifter may need grease as well...not sure if it's an alignment thing too.. Gravel getting tore up? 😢 lol The floor is sad but 8k 471cc machine with dump body.. You said it...the value is in the price and some things will need attention..

We took those seat bars off, it's real easy, makes entry much easier. My pet peeve was no spare tire, and there is are no after market rims. Had to buy an expensive Massimo front rim to get a spare. We have a 2018 700.

Ive had my 700 for 2 yrs oil change is not easy, but other than that I really like mine.

I'm not being a Dick or anything, but you're Knit picking.. the handles on the doors can be adjusted, the little handle beside the seat can be taken off or cut off, the shifter can also be adjusted on the linkage, The rubbers on the doors aren't going to last forever,, just like a bungy cord, they eventually break as well. The floor on the other hand, Yep, I'll agree with you there. They should've used something besides plastic, maybe a 11ga sheet metal or something like that, oil filter and drain plug, shouldn't have been that tight, know nothing big inner to tighten them down that tight. Good deal after 2yrs it's still running overall very well. Thanks for the review

always good to see an informative and honest video from an end-user :-)

I bought one and its a beast. Went through a mud hole my brother got an 1100 ranger stuck in. Only complaint, needs more power in reverse and cant find the limiter. Also feels weak during break in period but starts feeling better after 10 hours. If you want more power they have tuners and even turbo kits

I just got one of these from Lowe’s, I’m glad to see most of the negatives are kind of nit picky. I will look into armoring the floor. Thanks for the great information

I have a 2021 from Lowe's. I am pretty happy with it. I have the same thing about going into low. With only 65 miles it is stuck in 4x4. The switch does nothing. Has anyone else experienced this?

I've been looking at these. Thanks for the review!👍

I took the doors/windshield off immediately. Oil filter will need a newer style filter to be taken off with a socket versus a old style wrench. Small things like this makes life easier not to mention where you place your hands while closing any door. Pay attention to.small details and it will make life easier and yes, you can pay twice as much for a honda or a Polaris...

most of these after market machines are fine for running around the farm and hauling small loads on your property ,,, but if you want to run it like a ATV and swamp it in mud and jump hills ,,, they are not really made for that ,,, most after market are for light chores and normal driving

I bought one in 2014. I have had good luck with it for the most part. I had to replace the battery twice in 6 years. I agree the floor boards could be better. Most that i have seen did not come with power steering but it is a option and i added it to mine. It is well worth the $600 ish price. You can turn mine with one finger now. I had to replace the tires on mine and i went with a different brand to limit the damage to the ground the tires do. I do not like the live axel and wish it was limited slip. The arm piece on the seat can be removed with just a few bolts. I did that but put it back on because of the slop of the paths i ride on. It keeps you in the seat but it is a pain at times.

Is there transmission problems, or it's not stay charged

i have read the 500 it under powered. would you put a snow plow on this one.i live up here in michigan

The rails on the seats are removable!

Can you drive this on the road? I just bought one like this at lowes

Will you look at your tires and check the brand. I think it's the same pattern as mine. And mine is Wanda 26x10x12 I need a rear tire

Awesome stuff! I have a Massimo too. New sub!

Power steering is a option. I installed it on mine. Would not have another one without it. You can turn it with one finger. Floors are junk. I wish the rear axle had a differential. It is a live axle. In short it is a straight axle. I put led bulbs in my head lights. i purchased mine in 2014 and have not had any big issue with it. I do wish the charging system had more amps. My starter is kind of funny. I have noticed that on most of the ones that i have seen.sounds weak.thanks for the review.

where are they made and what about parts availability?

It seems like it would be like the best of all worlds for someone like me, a lot of utility plus would be fun to drive around. I always enjoyed ATVs, but at 45, i might be getting a little to old to do that kind of thing

Man I just bought one if these and basically everything you said is ABSOLUTELY MINOR I seen a couple reviews no body’s got anything bad to say about this little machine which makes me extremely happy

My won't start, lost power to fuel pump and spark plug. Can't find wire diagram

What happen to the engine? How it blow?

What spark plug are you using

Hello burns farm do they still manufacturer this model?

I used to deliver to them in garland tx they are pretty good it’s really a Yamaha and they been around for a long time

I looked a these ,I just ordered a polaris 500 there about $1000 more, but there are service dealers all over

Does that thing have any type of heater in it or can you buy one for it? Does it have any type of cover that you can put sort of over it in the winter? Thank you so much appreciate it

Great video! Thanks!

I was looking at one of these yesterday. Seems like a fairly solid little rig. The one I looked at had skid plates on it, so maybe that plastic floorboard will have some protection. Anyone know the top speed of one of these?

How to make it quieter?

door rubber catch things, i unhooked them. they were annoying. almost want to lose the doors and that side handle lol

How much did he purchase it for?

How bad was your Dads hand and leg? Did you say lighter or ladder?

I love it, so far

I've got one, remove the doors, why mess with them. Positive traction? Turn it off, it has a button . Easy. ??? Oil filter the 1st time, I agree. Floor, I use this everyday, not a issue yet.? Gears I agree, at times tough, I rarely have to gear down. Its recommended to drive and keep on High. I live out on the wilderness where the terrain cannot not be tougher, not a problem on high, it pulls right through. I took them doors and windshield off immediately after I bought it, dont miss them at all. As for that handle on your seat, I've had to hold on for dear life at times, I dont mind it one bit. Overall I'll agree with you, its affordable and so far it's been a good machine, I've been in places where no car or truck can, I do. Enjoy.

Are you able to haul this on a 5x8 trailer?

steering is a little hard, but i'd rather it be mechanical than hydraulic power and something else to fail

Most of the things you are knit picking on is also called wear and tear. EPS is not standard on all models and make, adjust the shift linkage that will help shift better. I have a 2018 Hisun 500 and on the first year after warranty, fuel pump went, I just shut up and bought a new one, no complaining here, these suckers take a lot of beating and still keep on running. Fun to ride and it is an expensive hobby just like a boat or anything else like that. Buck up.

All the things you mentioned are easy fixes. Spray lube would fix a lot of it.

Door needs oiling and adjusting the latch simple fix.

I think this is made by Hisun they are coming on strong in the side by side market Lowes sells a axis 500 with a winch, windshield, top, doors, signal lights, horn and has a 2 year warranty. For $9000 Beat that Honda and Polaris.

I'm having charging issues, we're would you start

Bought a no-name side-by-side, but expected it to be Honda quality. Bout rite.

More like $10,000 differences here in Alabama.. I have a axis 700. Got it for $9,000 tax and all..had a YXZ $ 22,000

WD-40 on the door latches. Remove those silly seat bars. Grease the joints all over. Replace the floor on the drivers side with aluminum and screws.

Can ya get or do they make a snow plow for it?????

It’s hard to steer because the tires are so nobby and it go’s into low very easy

Put some lithium grease on door latches, remove hoops on seats what I did

The bars on the side of the seats really suck. Having a locked rear end is bad .. it will destroy your yard.

This thing looks exactly like the Axis 500 ITV, it’s the same thing, only made in Texas. The warranty sucks too. Buy a used Honda 500.

After seeing your video I'm having some of the same issues. I didn't buy this rig,but it was given to me by someone close. We used it since new. Yeah,the oil filter was a challenge. But two major issues are: Ever since new 2018 ,this thing ran RICH . If fact,last month,I had to change the plug cause it got fouled. It was bought at Tractor Supply,and trying to get a filter from them or anything else was none and void. Then trying to see why works on these things was same. I live in Picayune,Ms. To where there is no one to work on them. I need to do something about this running rich. If I can't find someone or some idea to alleviate the problem I'll have to start changing parts,,(if I can get them). I warned this person when they wanted this thing to spend the extra money to get a better unit. But now,I'm stuck with it. Any help would be appreciated. JT.

2 bolts removes the brace on the drivers side and have you heard of grease you do know you have to grease the latches ! I have one and they sell a filter wrench for these that is simple to remove the filter and the block is aluminum if you warm the engine the plug removes easily ! Sounds like the machine is excellent you are just picky and not very mechanical ! This is a Yamaha clone its identical to a Yamaha even the parts interchange these are great machines if that's the only problem you have with a utv count your blessings ! SMH

Matienance goes along way.

How long is the warranty on them?

How much it cost one of this machine

You get what you pay for. If you want a Honda quality machine then you have to pay a Honda quality price.

I agree on what you might need it for but you got to use a little common sense to I am not knocking you at all about it but I've seen some people do some crazy things over the years I wish your dad the very best

HOLE IN THE FLOOR BOARD? ONLY 2 YRS OLD?

The plastic floor is a potentially serious hazzard. Im considering a Massimo but after seeing this,,, if i buy one i would have to install some metal for safety. Running over sticks is a common thing but with that thing its like playing russian roulette.

AHMAD

Your complaints are all just adjustments, pretty common with Chinese stuff. Also, the "power steering" isn't going to work with the engine off. Now the floor thing? Yeah, that's weak!

شبابي و نويت

The drivers floor is rusted out after only 2 years? How about you store it inside!

😂🤣😂🤣😂🤣🤦🏻‍♂️

😢bad

Glad I seen this

About that safety bar... use a sawzall or lose some weight

“One wheel drive” 😂 Some people truly couldn’t find their ass with both hands.

My in-laws have ordered one of these turds for my Son as a gift. They already have one and asked me if I minded them getting one for him. Hard to say no without looking like an ungrateful punk and calling the one they have a POS. But I am sure dreading bringing this waste of money home. No dealer support available like you'd have from a "real" manufacturer. Im really hoping TSC calls and says this outfit has been closed down or gone outta business and wont be able to fill the order and I'll just pay whatever boot necessary to get my Son a real SxS like a Pioneer, Ranger, or even a Deere.

Wow y do u even own 1 if u hate every thing about it also buy a yamaha honda pr Polaris if u want a quality machine u guys buy junk then complain

biggest piece of junk ever made . nothing but problems