Abandoned Yanmar Tractor WILL IT START? Part 7: Engine Rebuild

Рет қаралды 33,436

2 жыл бұрын

It's time to rebuild the Abandoned Yanmar Tractor diesel engine. This diesel tractor engine needs a complete rebuild. We need to rebuild the diesel tractor's head, replace the pistons, head gasket, and replace all the old gaskets and seals. WILL IT START? LET'S FIND OUT! PARTS & TOOLS ↓↓↓↓
➤Previous Video: Abandoned Yanmar Tractor WILL IT START? Part 6: Transmission Seals kzfaq.info/get/bejne/mdaiebKo2c7FhJc.html
➤ Service Manual (Yanmar Engines): bit.ly/3Lk7gVP
➤ ALL Yanmar Manuals!!!: bit.ly/3TexzyH
➤ Yanmar Engine Sleeve Puller Tool Plans: drive.google.com/file/d/1YhiBoAdpOfe33Y781iq0GgKOSMkblyB2/view?usp=sharing
Timestamps:
0:00 Intro
0:25 Disassembly
2:44 Head Removal
3:27 Failure Predictions
5:06 Piston Removal and Inspection
8:44 DIY Engine Sleeve Puller
12:30 Restoring Old Parts
16:50 New Tractor Parts
19:02 Cylinder Head Rebuild
23:46 Rebuild Steps
25:10 Wiring Repairs
26:53 Pistons & Sleeves Installation
31:52 Head & Engine Parts Installation
34:52 REVEAL
35:31 STARTING ENGINE
37:22 TEST DRIVE
38:13 Outro
Ingersoll Rand Air Tools:
● Impact Wrench: amzn.to/3H4Yzc2
● Air Ratchet: amzn.to/35xJYZW
● Die Grinder: amzn.to/3rYt6nD
Other Tools:
● Welders: amzn.to/3ko1qEc
● Click Torque Wrench: amzn.to/3vG0UZ2
● Beam Torque Wrench: amzn.to/3INZwaB
● Metric Socket Set: amzn.to/3MsoApx
● High-Flow Air Fittings: amzn.to/2J0PofR
● Impact Protective Boot: amzn.to/33xQ7Ex
Supplies:
● Tractor Transmission Oil: amzn.to/3tzsep7
● Rotella T4: amzn.to/3MzJ5jE
● Exhaust Stainless Punch Plate: amzn.to/3LvMv6W
● Permatex Aviation Gasket Maker: amzn.to/3FdhAIY
This is a Yanmar YM2000B Diesel tractor engine.
As an Amazon Associate I earn from qualifying purchases.
#willitrun #willitstart #restoration #automotive #mechanic #enginerebuild #diesel #dieselengine #tractor #tractors #farm #farming #yanmar

Пікірлер: 197

@MattsShop 2 жыл бұрын

Hey Yall! It's FINALLY DONE! ➤Abandoned Yanmar Tractor WILL IT START? Part 1: kzfaq.info/get/bejne/qJ6PnNZirqzQY5c.html Timestamps: 0:00 Intro 0:25 Disassembly 2:44 Head Removal 3:27 Failure Predictions 5:06 Piston Removal and Inspection 8:44 DIY Engine Sleeve Puller 12:30 Restoring Old Parts 16:50 New Tractor Parts 19:02 Cylinder Head Rebuild 23:46 Rebuild Steps 25:10 Wiring Repairs 26:53 Pistons & Sleeves Installation 31:52 Head & Engine Parts Installation 34:52 REVEAL 35:31 STARTING ENGINE 37:22 TEST DRIVE 38:13 Outro

@darrenhughes8106 4 ай бұрын

Great vid, do you remember the ft lbs of torque for the head bolts? Thanks

@Brookside975 2 ай бұрын

You are a very talented mechanic. I am 75. When I was in my 40's I bought a brand new Yanmar GT-14 garden tractor for my six acres. GREAT tractor!

@MattsShop 2 ай бұрын

Thank you I appreciate it! I bet your Yanmar is still running great!

@bennyhill3642 Жыл бұрын

That was a AWESOME Video young Man!!! Ive got the 2210 Tjose are some Great liytle tractors. And the great job you did, that engine should run for your Grand Children😇😁👍👍👍😇

@MattsShop Жыл бұрын

Thanks 👍 they are awesome tractors! I hope it runs a long time.

@michaelerwin7485 Жыл бұрын

First year owning a 3310D. Thank you so much for producing this series! Super helpful and well explained!

@MattsShop Жыл бұрын

You're welcome!

@jeremiahthomas2669 Жыл бұрын

That's a really nice tractor can't believe somebody left her out in the cold all alone. Thanks for saving her matt

@774rr8 2 жыл бұрын

I am a mechanic of Kubota in Japan. I was impressed by your maintenance technology.

@MattsShop 2 жыл бұрын

Thank you. Hello from USA

@friedac.4312 6 ай бұрын

Smart guy!!

@dougsmith632 Жыл бұрын

This is probably the best tech video that I have ever seen. Your tech skills are first rate, and your editing gets the information across quickly and clearly. Well done........I have been a tech for 45 years.

@MattsShop Жыл бұрын

Wow, thanks! I appreciate it. I put a lot of work into this video!

@KrisDouglas 2 жыл бұрын

One thing you can say about a Yanmar diesel is that they are well engineered! Absolutely solid!

@MattsShop 2 жыл бұрын

It's built like a tank!

@rickkatz4692 Жыл бұрын

I like that you pay attention to details.

@MattsShop Жыл бұрын

Thanks!

@gsman5828 Ай бұрын

Wow! You have some serious mechanical skills. Not your average mechanic. I own a YM 1500 Yanmar (1978) that is bullet proof. They are great tractors.

@8.3leader15 Жыл бұрын

Absolutely awesome. I got a 336D thats in good shape but i dream of fixing up for real. I very much appreciate you taking the time not only to fix up this tractor, but to share the process in such detail. Thank you VERY much.

@MattsShop Жыл бұрын

You're welcome. The YM 336D has dry engine sleeves, not wet engine sleeves like this YM 2000. Just a tip.

@chairmankim9628 Жыл бұрын

Outstanding rebuild job. Probably runs better than when it was new.

@MattsShop Жыл бұрын

Thanks, it does!

@lawrencesolman6673 2 жыл бұрын

Yes! Congratulations on your successful rebuild! I've been watching after I spun a rod bearing in my Yanmar. The lesson I had to learn the hard way: ALWAYS check your fluid levels before you run it even if it's only going to be a few minutes... Your Yanmar turned out absolutely awesome! You do top notch work! Do you want to do mine next? 🤣🤣

@MattsShop 2 жыл бұрын

Thanks man. Yea, always check your oil! Sure haha

@colincrisp1592 Жыл бұрын

Hi I just purchased a yanmar 1700 I think the rings are gone Hell no not me some one else can do it to much work I must thank you I almost was going to take the head off THANK YOU FOR SAVING ME CHEERS

@tuesboomer1623 2 жыл бұрын

Outstanding! That was a long, tough, job and now you have a good, hard won piece of machinery. It was great to hear it start up and see it 'motating'!

@MattsShop 2 жыл бұрын

Glad you enjoyed it. Yes, it was a TON of work. I went through the ENTIRE tractor. It was worth it.

@Brad_Spit 2 жыл бұрын

That's how you do a restoration! Love your work Matt! Flawless! OCD at it's best!

@mister7596 2 жыл бұрын

crazy u just uploaded few hours ago started watching this playlist perfect timing sir

@thomastaylor5766 Жыл бұрын

Love your videos. Diy is only way to learn.

@MattsShop Жыл бұрын

Thank you. Yes, it is! Trail and error.

@MrRain-hk4zi 11 ай бұрын

Enjoying the series. I have a YM1700 and videos like these help one get familiar with the "guts".

@MattsShop 11 ай бұрын

The YM1700 is very similar to the YM2000!

@povilasivaska4113 2 жыл бұрын

Resurrection of machines, restoration master, Matt's Shop!

@MattsShop 2 жыл бұрын

Thank you!! I appreciate it!

@povilasivaska4113 2 жыл бұрын

@@MattsShop Today i work with YANMAR YM1702D planting potatoes, Like this mini Traktor, old but good 🚜! Good luck to you, I am from Lithuania small country in Europe 🇱🇹😃👍

@steve_n_utahthediyguy9263 5 ай бұрын

Wow…wow..wow! AWSOME job..very well done video!

@MattsShop 5 ай бұрын

Thank you very much!

@GreenRiceAndHam 2 жыл бұрын

Great video! It is incredible seeing the amount of dedication you have to see this project through this far! I like your content and I hope your channel grows.

@deadlydavem 2 жыл бұрын

Great video! These are fun little tractors. Gotta wonder why that piston was broke. .

@PaddyGun 2 жыл бұрын

He done a great job with his project, that engine should see at least another 20 years

@MattsShop 2 жыл бұрын

Thanks! I'm going for 40 years haha

@AmsterdamCesar 2 жыл бұрын

Hi Matt! Again a great video! Finally you got it running! I learned a lot from your vid. Thanks for that 😀 Greetings from Europe!! 💥💫💯

@MattsShop 2 жыл бұрын

You're welcome! I'm glad I could help.

@williambehles7704 2 жыл бұрын

Laughing, Attaboy Mathew! Did my heart good to see and hear the results. How much money do you figure you invested in the rebuild?

@MattsShop 2 жыл бұрын

Thanks for watching! Probably $1500-1600, but I went all out. You could do it cheaper.

@williambehles7704 2 жыл бұрын

Going all out and replacing everything saves retracing steps though. No point in doing the same jobs 2 or 3 times. For $1600 and a WHOLE lot of work, you have yourself a good little tractor. What do you plan on doing with it?

@packattack1762 Жыл бұрын

It’s a $15,000 or more tractor these days so you did extremely well

@brianedwards231 18 күн бұрын

Getting ready to conduct the same operation on my Yanmar 2610 3T80 3 cylinder engine….. As soon as I remove the front bucket.

@MattsShop 17 күн бұрын

I'll buy that bucket off your tractor. Let me know when you get it off haha

@thatguyoverthere9634 2 жыл бұрын

"Way more tedious than it should have been" Meanwhile: I'm doing my first engine rebuild with one of those harbor freight ring compressors and beating the pistons in with the handle of a hammer. In all seriousness, great work with this build

@MattsShop 2 жыл бұрын

I don't recommend it!! Thank you.

@johnrolston4242 7 күн бұрын

Best job I have seen

@MattsShop 7 күн бұрын

Thank you!!!

@dennisharrison4744 Жыл бұрын

Just got both front nuckle on my yanmar 155d 4x4 rebuilt tractor 100% machanicly sound so smooth now

@rickkatz4692 Жыл бұрын

Good job, I have a 1700 with a front loader on it. It's a beast.

@krstoner53 2 жыл бұрын

Okay, I got to give you a hard time here, turn that oil jug 180 and get you an S hook and bend 90 degrees to hold that top link up. Seriously though great job. You are very thorough with everything you do. You probably got the best redone Yannie around I would think.

@MattsShop 2 жыл бұрын

Good tip! I get in a hurry and overlook simple tricks like this lol. Thanks! I sure hope it's the best refurbished Yanmar around.

@brngrofdeth 2 жыл бұрын

Excellent job Matt dude! Well done! Love and blessings from Ontario Canada!

@MattsShop 2 жыл бұрын

Thanks. What's up from USA

@elmermason9685 2 жыл бұрын

Nice rebuild. Sounds great.

@MattsShop 2 жыл бұрын

Thanks 👍

@francovitulli4922 Жыл бұрын

Hi Matt, I'm super impressed of the result. I'm dealing with a JD 1050 yanmar engine 3cyl. I'm amateur and this project it's taking forever. Any suggestion on how to detect issues?

@namodio12 2 жыл бұрын

Great job, it looks great!

@MattsShop 2 жыл бұрын

Thank you!

@bruceswope179 2 жыл бұрын

Great Job.... I really enjoyed your Video !!

@MattsShop 2 жыл бұрын

Glad you enjoyed it!

@sethhill5689 29 күн бұрын

if you had welded the nut to the angle iron, you could have used a power tool on the top welded nut to remove the sleeves also.

@stefvanoudtshoorn2304 2 ай бұрын

Great job!

@MattsShop 2 ай бұрын

Thanks!

@jimbop101 2 жыл бұрын

U da Man Matt. Great job congrats......Mine still broke :(

@MattsShop 2 жыл бұрын

Thanks! Get it fixed. This video should help.

@vagelismargaritis1137 2 жыл бұрын

Very good congratulations

@JOESTV74501 2 жыл бұрын

good job, looked like fuel gauge wasn't wanting to play well

@beachthor1 10 ай бұрын

Great job!!

@MattsShop 10 ай бұрын

Thank you!

@rockinhonda Жыл бұрын

Nice Job Matt!!

@MattsShop Жыл бұрын

Thanks!

@Dracuvindepeste 2 жыл бұрын

Nice job, dude!

@MattsShop 2 жыл бұрын

Thanks!

@bradleymcclintock7771 Жыл бұрын

Great job. !!!!!!

@MattsShop Жыл бұрын

Thanks!

@lewis2553 Жыл бұрын

Aw, man, I was hoping to see you remove the harmonic balancer, so I could see what kind of puller, if any, you used. I have to go in there on mine and see why my oil pressure is dropping. I've eliminated almost everything except the oil pump. The rod bearings don't show much wear, so I assume the rest of the engine is probably okay. I repaired the oil pressure regulator already. It's spring had rubbed on the wall of the bore and was almost in two. Plus, the ball seat looked like it was chipped on the edge of the hole. A Dremel tool and a ball shaped rock fixed that right up. It just happened that I had bought a whole sheet of those rocks a few weeks ago for another project. 😂 I also had some similar springs in a pack of springs that I had bought from a building supply store decades ago. They were the same diameter and had the same number of turns of about the same thickness of wire. The only thing I had to do was to stretch one out and then stress relieve it to get it to proper length, being careful not to distort it, so it wouldn't rub on the bore wall like the last one. It gave me 48 PSI - just right! It has worked for a long time, but now the pressure is dropping as the temperature rises. Also, my gauge reading has been fluctuating rapidly in time with the engine firing, so I'm thinking maybe I have a damaged pump impeller lobe or something like that.

@hotboy2659 Жыл бұрын

Wow man your amazingly talented.

@MattsShop Жыл бұрын

Thank you!

@tomkergil3304 2 жыл бұрын

Thanks for model number (2TR20A). Not what TractorData lists but what do they know. I have a Yanmar 2TN66C engine to go through. Fear it was dusted. What are my chances of finding wet sleeves which I can replace? Will be making a sleeve puller like yours if that is what I find. Thanks for the help.

@MrRain-hk4zi 11 ай бұрын

Nice job!

@MattsShop 11 ай бұрын

Thanks!

@FabMar-hd4eq 4 ай бұрын

Bon travail !😊

@harolddalesr8365 Жыл бұрын

Sounds like that movie character , " Joe Dirt " .

@headpainter1 Жыл бұрын

Got the head and pistons out of my 3 cyl yanmar. Gonna go back with 3 new pistons and cylinders. I saw that some say to use a cylinder hone on the new cylinders or do they come already honed? My pistons/rings weren't broken but the top of 1 looked like the crown was coming off as top ring groove was 2x wide. Ordering full rebuild kit soon. 2 cyl were pitted near bottom. Head cracked by 2 injectors so new head as well. Common issue on these I think.

@Shepherd_Flute_on_the_way Жыл бұрын

Matt, you are a great guy I ever watched over all the KZfaqrs so far! BTW, can I buy the rebuild Yanmar YM1610 from you? I trust your work!

@MattsShop Жыл бұрын

Thanks! You're the best commenter so far! Haha nope. I have plans for this tractor.

@Shepherd_Flute_on_the_way Жыл бұрын

@@MattsShop Best Wishes to you and will keep on following your videos and put thumbs up too. Great videos!

@bigkat1919 2 жыл бұрын

I still think the wrong type of coolant was used and caused hot spots on the cylinder liners/sleeve. Good job Matt!

@MattsShop 2 жыл бұрын

Thanks, I'm not sure. I think all the water was boiled out of the coolant. The coolant that came out was very thick and dark green. IDK if it's possible. Just a theory.

@olegrumpy4519 Жыл бұрын

@@MattsShop Don't use green anti-freeze in a diesel with wet sleeves. Get the red OAT stuff. It will save you in the long run.

@mcarroll598 2 жыл бұрын

Great f-in job man!!!

@MattsShop 2 жыл бұрын

Thanks!

@filipradisavljevic7980 11 ай бұрын

In serbia we still use tractor simular to that one yust with more powerfull engine. They are moastly made in 80's and we still use them more then modern ones. Moastly IMT 533 or IMT 539.

@MattsShop 11 ай бұрын

Thanks for letting me know! Whats up from the USA.

@tammanybrady3543 Жыл бұрын

great video. What is your training?

@KrisDouglas 2 жыл бұрын

That red paint inside the engine is likely a *very* tough oil resistant enamel, common on British diesels as well.

@MattsShop 2 жыл бұрын

Good to know.

@marczeve7072 2 жыл бұрын

Finally....... 😃😀Careful with the radiator, expensive copper part.....I know....

@MattsShop 2 жыл бұрын

I was! They don't make them like that anymore.

@dennisharrison4744 Жыл бұрын

Probably havnt ran that strong in years iv got a 155d motor realy strong on it putting brakes on it and a few bearings in the front left knuckle but after that be good shape

@MattsShop Жыл бұрын

Yea, Thanks! Sounds like yours doesn't need much work.

@tomkergil3304 2 жыл бұрын

You did GREAT. Sad the owner left it standing with worn out antifreeze water in radiator. What model Yanmar engine?

@MattsShop 2 жыл бұрын

Thank you. Yanmar 2TR20-A

@ARKO1324 2 ай бұрын

Wiesz może ile powinno wynosić właściwe ciśnienie wtrysku w tym traktorku?

@tejeda7324 2 ай бұрын

Hey Matt, question once you put the Head gasket and you put the engine back together after adding fuel and all oils is it just Plug ang play? or do you need to do anything extra once you put the engine back together before your turn it on?

@christophergallagher531 Жыл бұрын

When the sub assemblies start going on a block, I start feeling a building anticipation

@christophergallagher531 Жыл бұрын

No different watching you make this happen! I can't help but wonder what went wrong in the first place. Just one nasty overheating? Congratulations! Chris

@MattsShop Жыл бұрын

The motor was overheated. The cooling system was leaking (no pressure) and it was worked hard like that. Probably used starting fluid too.

@christophergallagher531 Жыл бұрын

even a dumb nuts like me would not use starting fluid in a diesel! I have seen loggers use DW 40 for old low compression chain saws.

@MattsShop Жыл бұрын

@@christophergallagher531 A lot of people do it and it blows them up.

@christophergallagher531 Жыл бұрын

@@MattsShop There is a dead D5 behind the saw mill over that. Poor thing only got. creek water for coolant. Short life all around.

@Youroko11 2 ай бұрын

Previous owner could have used starter fluid. Not good. Seen it before

@MattsShop 2 ай бұрын

I'm sure they did that's why it was destroyed

@headpainter1 Жыл бұрын

Maybe I missed it, but did you pull the compression numbers after the rebuild? I saw the 100/200psi pre build numbers. Awesome job by the way.

@MattsShop Жыл бұрын

I did compression test it afterwards, but it was useless because the big thick diesel rings take time to seat. It gave a false low reading. Thanks!

@boto669 Жыл бұрын

Maybe, it is now time to do a commpresion test :)

@riannastraw5297 2 жыл бұрын

Yay!😄

@MattsShop 2 жыл бұрын

I know you've been watching the progress.🤣

@yanmar1050 Жыл бұрын

Good morning. do you have service book for yanmar ym 2000

@josealatorre9938 Жыл бұрын

Where did you order all the parts or the rebuilt kit.

@rickkatz4692 Жыл бұрын

If you put a front loader on it I have some suggestions on buttressing the whole unit to the chassis. Otherwise you will be having trouble with the bolts on the belly always coming loose.

@MattsShop Жыл бұрын

What are your suggestions? I have been looking for a loader. Hard to find right now!

@rickkatz4692 Жыл бұрын

Once you get the front loader your going to not trust the 4 belly bolts unless you weld the under brackets to the sides and make shure the belly bolts are secure weather there number 8 or not. Just make shure the bolts on the belly pan are not broke and sliding under the belly.

@rickkatz4692 Жыл бұрын

I'm going to have to send you pictures to explain.

@DennisKenneybees 3 ай бұрын

It looks like you did not stagger the ring gaps. I hope I am wrong.

@MattsShop 3 ай бұрын

I did stagger them.

@brianedwards231 17 күн бұрын

I would like to know RTV sealant you used if any? Thanks

@MattsShop 17 күн бұрын

I only used real gaskets and Permatex Black Aviation gasket maker.

@tadaskabliukas2797 Жыл бұрын

where did you download the engine parts from?

@nowthisisfishing Жыл бұрын

Did you use original sleeves or did you replace them I can’t seem to find sleeves for my 2t80u-j

@MattsShop Жыл бұрын

I bought new sleeves from hoyetractor.com

@rjose610 Жыл бұрын

What type of coolant goes in one of these

@royholt6980 Жыл бұрын

starting fluid

@Jimmy-iz1nu 9 ай бұрын

I think they put a hand full of mud in each port before they send it over to the states.😢

@MattsShop 9 ай бұрын

I know right??

@rjose610 Жыл бұрын

I have a yanmar 1610d. What kind of coolant does it take ?

@MattsShop Жыл бұрын

I use regular green coolant 50/50 mixed in mine. Some people say to use "anti-cavitation" coolant or an additive to help stop wear on the cylinder liners. I haven't tried it.

@garymichael3313 9 ай бұрын

Starting fluid caused the damage.

@MattsShop 9 ай бұрын

Yup, that's what I think too. Blew it up and broke the pistons.

@issahalhaji8356 2 жыл бұрын

Thanks for the good work done but how can I get the parts to buy?

@MattsShop 2 жыл бұрын

www.hoyetractor.com/

@Uncle_Sasha_no.1 2 жыл бұрын

На дворе месяц май, а у тебя и конь не валялся))

@Woodwardm88 9 ай бұрын

What was your final compression readings on the cylinders after the rebuild?

@MattsShop 9 ай бұрын

I checked it again and I had very low compression like 200PSI. Found out it was pointless to check compression on these diesel engines with the thick diesel rings. They take forever to break in and seat.

@Woodwardm88 9 ай бұрын

@@MattsShop Thats very interesting. I had 300 psi on each cylinder of my ym187d. I put new rings and pistons in it and had the head done. My final test was 350 psi. Not much gain lol

@MattsShop 9 ай бұрын

@@Woodwardm88 That's exactly what I'm talking about. People said it needs 600-650 PSI to run right, but they are wrong. Testing the compression on these Yanmar diesel tractor engines after a rebuild is a waste of time. The compression is probably much higher after the rings seat. I never rechecked the compression after I broke it in.

@rottmanthan Жыл бұрын

would you say that was due to high hours or uncommon issue? cant remember if i asked about it before.

@MattsShop Жыл бұрын

Pretty sure someone overheated it due to a radiator leak. It damaged the pistons. Then they probably tried to use starter fluid. It's common with these older tractors. They get ran HARD!

@rottmanthan Жыл бұрын

@@MattsShop oh ok, ya i know staring fluid is not good for a diesel

@sgtjan5241 2 жыл бұрын

Did you rotate each piston ring about 90°? The openings should not overlap to each other.

@MattsShop 2 жыл бұрын

Yes, they are staggered 180 degrees apart.

@sgtjan5241 2 жыл бұрын

@@MattsShop I have the same yanmar but with a three cylinder diesel engine. The coolant tank is also shot. I'll take a look at hoye parts. I replaced the clutch recently but other then that this thing runs like a champ. Nice video series 👍

@MattsShop 2 жыл бұрын

@@sgtjan5241 Thanks man. You can get the coolant tank. You need to modify the coolant level wires that come out of the bottom of the old coolant tank.

@topcity3783 2 жыл бұрын

What is this bottle that is poured into the air filter, is it oil or something else, and what kind of oil is it?

@MattsShop 2 жыл бұрын

What part of the video?

@redfish3204 2 жыл бұрын

Matt, what site or vendor did you buy your stuff from?

@MattsShop 2 жыл бұрын

Hoyetractorparts.com

@mingorodriguez6486 2 жыл бұрын

Just bought a 1982 2620d where can I find parts for it?

@MattsShop 2 жыл бұрын

Hoyetractorparts.com

@brandonlee3875 2 жыл бұрын

Hey were did you get the parts I have a 1700 lot of blowby and smoke I want to rebuild it

@MattsShop 2 жыл бұрын

Hoyetractorparts.com

@brandonlee3875 2 жыл бұрын

Ok I found it thanks

@rjose610 Жыл бұрын

Can you explain what the dash symbols are ?

@MattsShop Жыл бұрын

One is battery fluid level (obsolete), overheat, coolant tank level, and oil pressure. Basically dummy lights. If one is on it means "check this".

@brada4018 Жыл бұрын

Where they using water for coolant?

@MattsShop Жыл бұрын

Nope! It's still a mystery.

@smoothbore4377 Жыл бұрын

Did your nose ever heal up, ... after paying through it for those parts from Hoye ?

@lionjutt9740 Жыл бұрын

Brother i need overhulkit yanmarr 1300d

@japi2020 Жыл бұрын

hi Matt, what is your address so i can drop off my JD 650 for repair.

@johnwils9208 11 ай бұрын

How much the parts to repair the tractor?

@MattsShop 11 ай бұрын

Depends on how much work/parts you need at least $1000 if you go through everything and rebuild the head.

@DennisKenneybees 3 ай бұрын

Look like you did a great job but looks like a money pit. Is the tractor worth the amount you had to spend for the rebuild?

@MattsShop 3 ай бұрын

Yes it was worth it 100%

@issahalhaji8356 2 жыл бұрын

So this engine you don't need to adjust any Timmins.

@MattsShop 2 жыл бұрын

Timing is set by a gear. Only adjustments: valves, governor, injector pop PSI, and injector pump timing

@user-ht5gs7yn4k 8 ай бұрын

Dich tiếng việt được o bạn

@adamslayer3992 3 ай бұрын

Somebody sprayed the shit out of that engine with either

@MattsShop 3 ай бұрын

YUP! Never use it!

@adamslayer3992 3 ай бұрын

@@MattsShop you did a great job my freind

@randr10 Жыл бұрын

Anyone know what would cause this to happen on a diesel engine? I rebuilt a Kubota engine last year and it had the same problem, except just one cylinder. My working theory is that it's related to poor air cleaner maintenance since I found the entire inside of the intake with dust in it (air cleaner looked to be original to the machine from 1986 and it was see-through). Rest of the engine was absolutely perfect except for corrosion on some of the bearing surfaces. I'm assuming that was from acidification of the oil from combustion byproducts inside the oil. They ran it a long time with the broken piston to the point that the chunks of aluminum were missing and the chunks of broken ring had tumbled around in the void enough that they were little egg-shaped beads. Having seen that carnage and all the wear to the valves/seats and the other two cylinders as well, I was blown away that the crank wasn't even out by a half a thousandth. It was absolutely perfect. Journals on the cam and the cam lobes measured exactly to factory spec too. Must have had less than 1000 hours on it.

@headpainter1 Жыл бұрын

I can't help but wonder if the broken pistons were caused by previous individuals use of ether starting fluid.

@randr10 Жыл бұрын

Sorry, I skipped over some details. The overheating of the piston would be caused by the hot spotting of carbon in the combustion chamber. Essentially the carbon build-up gets red hot and ignites the fuel as soon as the injector goes off, which happens as the piston is coming up, so it's trying to compress the gasses as they're exploding, which creates extremely high cylinder pressures and temperatures. I think that may be the cause of my cracked piston. Weird how a simple air cleaner failure can lead to such a complex engine failure.