How fix problem then brew unit don’t fixating in Melitta coffee machines. Video guide with solving procedure.
Пікірлер: 24
@Sargejee14 күн бұрын
Had error 8 and brew unit got stuck inside, followed this excellent video, all good, thank you !
@OlegPC14 күн бұрын
My pleasure. Thanks for nice words
@adzib182326 күн бұрын
Fantastic video, thank you, and like others here my machine is working again just fine :)
@OlegPC26 күн бұрын
Not at all. Superb, that all works fine now.
@user-dn8gz6mz2y5 ай бұрын
Many thanks. Very informative. Took me through fixing the problem. Machine now is working again 🙏
@OlegPC5 ай бұрын
My pleasure. Thanks for your comment )))
@olekristianbjerkeli Жыл бұрын
Thank you soo much. Because of your instructions I could enjoy a newly brewed cup of coffee again. 👏😀
@OlegPC Жыл бұрын
Your welcome. Hope machine will work perfectly
@timursturua7046 Жыл бұрын
Дякую! Thanks to your video managed to repair my coffee machine easily. The problem was in faulty contact switch
@OlegPC Жыл бұрын
My pleasure))) This switches are often bringing trouble for Melittas, but then you knows where problem might be - this problem will be resolved in couple seconds )))
@vicekhrd11 ай бұрын
Many Thanks for this video I manage to fix my machine!!!!!
@OlegPC11 ай бұрын
My pleasure))) If problem will appears again - recommends to change two microswitches on brewing motors ring (under cover).
@jesusmartin446411 ай бұрын
Hi! Is there any way to contact you to get your service online? Thanks
@OlegPC11 ай бұрын
Hi. Write a massage to Viber or Telegram +380965080405
@terryterry16552 ай бұрын
mine without frother but indication light comes on ? help
@OlegPC2 ай бұрын
What do you mean “indicator light come on” ? What indicator ? Why it shouldn’t?
@terryterry16552 ай бұрын
@@OlegPC the froather light should not light up since my solo comes without a froather,rite. anyway.press to brew only resulted in sound..no grinding of beans or any flow of water /coffee/why? cleaned grinder..next i will check the tubing mechanism
@OlegPC2 ай бұрын
@@terryterry1655 Shower indicator - signals of air in water circuit (machines understand no or weak signal from flowmeter so). You need to press “bean” button. After - some water sends throw drainage valve in tray. If error don’t go away and light shows again and again - problem in flowmeter - or some dirt it water or rust on contacts wire.
@janekkowalski715811 ай бұрын
7:02 Mine doesn't move as easily as you do
@OlegPC11 ай бұрын
I understand - there was gears without metall ring in 2012-2014 model years machines. And they are turning not so easy as later one with metall ring on gear shaft. Surprise, but old one work as well as new one.
@janekkowalski715811 ай бұрын
@@OlegPC I'm doing a test but the water escapes me through the drain, not sideways instead of into the cup, when I press the hot water itself, it flies into the cup.
@OlegPC11 ай бұрын
@@janekkowalski7158 Just yesterday i got a problem machine - metall shower in top piston and hole with crema valve - was blocked by coffee parts ( coffee oil). So, mashine cant send water throw brew unit and sand it to tray. It looks like Drinage valve problem.
@janekkowalski715811 ай бұрын
@@OlegPCBy the way, my coffee machine is a Melitta Barista T. Maybe you know how the motor should be set up in the Barista T model?
@OlegPC11 ай бұрын
@@janekkowalski7158 Actually- the same as in this Varianza. So as on any Melitta or Nivona - on Main shaft ( on main gear ) - there is bevel. The line on this bevel must be parallel with down side of brewing motor case. Around 30-40 degrees, if my eyes don’t cheats me )))