Mercedes Benz Replace Combination Turn Signal Switch / Toggle / Stalk - C-Class

Mercedes Benz Replace Combination Turn Signal Switch / Toggle / Stalk - C-Class - W203 C320

Рет қаралды 265,332

7 жыл бұрын

I'll show you how I replaced a turn signal switch AKA stalk AKA combination switch AKA toggle. This is the entire signal stalk that is used for turn signal and is also a combination switch for other functions. I replaced the switch because it was broken and would not stay clicked on when trying to turn left. It would turn off or "self-cancel". This can be used as a guide for W203 or 2001-2007 Mercedes C-Class Sedans.
You'll need just a few tools:
- Torx T30
- Torx T10
- Flathead Screwdriver
- Breaker Bar with 10mm hex

Пікірлер: 113

@omarcolwell6978 4 жыл бұрын

Thanks to do it simple, easy and fully explained! This fit with c240 w203 2002 also. Was seeing tons of awful videos trying to take out the steering wheel and, if I follow them, sure will get damage my car electrics. Continue do in it like this! THANKS AGAIN!!!! A real pro!

@yogeshshrivastava1943 3 жыл бұрын

Wow, one of the best instructional video I've ever seen. Thank you.

@chrisstuffel6819 2 жыл бұрын

Agreed. I'm a tech, but I usually run from anything German made, but this is a good one

@romeohulu9194 7 ай бұрын

Thanks for the video! It was easy to follow and just swapped the switch out myself. God Bless 🙏

@SkylahSengvilay 2 ай бұрын

Thank you for creating this video. Extremely helpful and it’s easy to follow. Thank you again for taking the time to create this video.

@samsizer9093 6 жыл бұрын

Great instructions, thank you. I just did my 2006 CLK in the UK following this guide and it worked although the airbag clips are slightly different to mine.

@Jeremy64444 6 жыл бұрын

Good video, thanks it was a great help. Just two things, You should fit the locking piece before you remove the airbag squib. And if you remove the plastic clips over the switches first. You can remove the airbag squib and the steering angle sensor as one piece, which means the copper connections are not exposed.

@JahinIinI Жыл бұрын

Excellent addition to a very well done video.

@Noname-fv4pq 11 ай бұрын

¿cuál es la pieza de bloqueo? ¿pin rojo? ¿dónde comprarlo?

@brianneal8640 6 жыл бұрын

I followed the instructions although the clips on the air bag were different slightly ,they didn't unclip the same but with a bit of fiddling around got it to work, everything else worked fine and when I connected the battery again everything lit up as before and no fault messages at all ,many thanks and I saved about 300 bucks

@tradtony 3 жыл бұрын

This is a great video,I use a lot KZfaq instructions,this is clear,concise and very explanatory,good work!

@ThingsLike 3 жыл бұрын

thank you for the compliment, I appreciate it!

@tif321dc Жыл бұрын

Great video. I'm a little nervous about doing this but with your video I think I can do it. I'm a little confused about cutting out the plastic.

@tif321dc Ай бұрын

I feel the same way great video I wish he had shown a little bit more about cutting the plaster out but it does look dullable.

@japanyoucan8544 5 жыл бұрын

Thanks, nice clear instructions 👍

@radmansa5514 6 жыл бұрын

Good clear instructions, thanks for sharing

@aleks0001 7 жыл бұрын

Great video, very clear :)

@runeemblemsvag987 3 жыл бұрын

Thank you for sharing. It helped me a lot when I just replaced my switch today.

@ThingsLike 3 жыл бұрын

I'm very happy that this video helped you!

@moneymikeslickwill8749 5 жыл бұрын

You sir are the real mvp much thanks and may god bless you

@ashleyrowe2945 5 жыл бұрын

Did this job as per the video , exactly as shown , excellent instructions, many thanks !!!

@ThingsLike 5 жыл бұрын

I'm glad it helped you!

@jimbennett5595 3 ай бұрын

Great video buddy

@andrehuntley9228 4 жыл бұрын

Very helpful thanks for the info...

@alexandervanwyk7669 4 жыл бұрын

Your video is superb, thank you so much for posting. Ill try it on my 2003 A190

@ThingsLike 4 жыл бұрын

You're very welcome! Thank you for the comment. Hope it works for your A190

@jacjab9153 4 жыл бұрын

nasze wspaniałe autka , i bezpieczna jazda dla siebie i innych

@johnh2937 4 жыл бұрын

Excellent! Thank you very much.

@anthonyautomobile8089 Жыл бұрын

Excellent

@jimstraub7573 Жыл бұрын

Thank you!

@Portispro Жыл бұрын

Hi after I did this procedur, the srs, esp and bas start to shine, I took it to a work shop but they could put the light out.. they didnt have the oem mercedes software but they clamid that something is wrong with the esp, airbag and brake sensor, any idea what have could happend?

@mariagianna9676 Жыл бұрын

I am experiencing the same problem. The Srs and Esp are illuminating now. I can't figure it out. I even calibrated the steering wheel and it didn't help. Anyone know of a solution?

@Portispro Жыл бұрын

@@mariagianna9676 maybe something have happend to the clockspring/steering indicator, I took it out and have it back to the center by turning it from side to side and the turn it back to the middle, and then I could have warning lights out

@razaiw2113 2 жыл бұрын

Thank you bro

@daiboot 3 жыл бұрын

Top video...thanks

@emirwati 6 ай бұрын

Thanks for the video. BTW, what is the name/ reference of the 10 mm hexagonal bit? Didn't you have difficulty to remove the central nut? Please continue with the good job, like that you can help many of us. Regards.

@rumipezo259 6 жыл бұрын

thanks for share, i will try to repair

@martinboucaud679 2 жыл бұрын

thanks for this video.

@1guruGabby 2 жыл бұрын

Thank you :)

@mehmetozsever8831 2 жыл бұрын

What could I use instead of the lock pin for the steering angle sensor? Since my package didnt include one.

@navithefairy 2 ай бұрын

Great video, gonna try it now. My indicator won't jump back after a turn.

@buck_up 2 жыл бұрын

Need that specific torx set, long skinny end.

@tif321dc Жыл бұрын

Great video. There are so many different companies selling the part is there one that is recommended that also comes with a locking pin? Thanks again

@CrucialSpeaks 3 жыл бұрын

VERY GOOD

@danielb2145 2 жыл бұрын

Thanks.

@mtezman3465 Жыл бұрын

Thank you. Is there a way to find the part code before I disassemble the unit? I need mine changed and the repair place wants the part code or / if it's a 5 or 6 pin make.

@strikingbg6024 2 жыл бұрын

very useful

@letdmichael Ай бұрын

Very informative video. Unfortunately, you did not share the video for the cut out plastic. I am not sure how much and where to cut.

@alexnova85 3 жыл бұрын

Thank you

@Statam31 2 жыл бұрын

Bien

@SteveRogers461 4 жыл бұрын

Excellent video! Thank you for sharing 😊

@ramongracia536 2 жыл бұрын

God video 👍👍

@theelephant5974 2 жыл бұрын

Is there a way I can change it from the left to the right side? I swear this thing drives me crazy

@hanne743 6 жыл бұрын

Hi just one question, if you do this won't you get any fault message on your display? Or if you get how can you reset them? Thanks a lot for the good video!

@adambelgacem3117 11 ай бұрын

very nice but do you think i can diy fix the switch without having to replace the whole thing?

@herve5784 2 жыл бұрын

Merci très utile

@jperelladams6146 6 жыл бұрын

Does this method also works on a 1995 s class 320

@docselva 4 жыл бұрын

Bro. Is the left hand and right hand drive the same replacement...compatible? Thanks

@jakubbittner2161 5 жыл бұрын

hi i have a question, i have to have that red plastic key

@manuelgalvan4150 2 жыл бұрын

So I followed everything you put on here but apparently my steering tilt didn’t work afterwards. I don’t hear the motor run when I press it but my motor works cause it works when I turn off and on my car. Can you help me?

@Omurpasaoglu 2 жыл бұрын

Hello, I have a Mercedes w203 turn signal that works by itself, without Mayo it turns on and does not turn off. What I did: 1) pulled out the turn signal switch chips but the turn signals continued to work. 2) I pulled out the chips of all 4 lights and the same thing. What could be the problem? Help rozhalusta. Thanks in advance everyone.

@S4Rasho 6 жыл бұрын

Can you Made a video for aux adapter or something helps to listen mp3 on w203 Mercedes 2003 please

@Newstarboy1907 5 жыл бұрын

2:54 what name is that in red???

@shandamanable 5 жыл бұрын

Any tips for if you don’t have a red clip to lock in the steering column?

@scottwalker2297 3 жыл бұрын

A paper clip or baling wire will work

@Noname-fv4pq 11 ай бұрын

@@scottwalker2297 ¿qué función el clip rojo? ¿donde comprarlo?

@bhasins Жыл бұрын

Where do you get the angle locking clip from?

@country7216 Жыл бұрын

@bhasins , i think he said it comes with the new replacement part in the box.

@ALIALHASSANdoctor 10 ай бұрын

Where to buy this, in uk

@EndofUSA 4 жыл бұрын

So for those having the same problems with their turn signals lights staying on, it is the TURN SIGNAL SWITCH that is the culprit and not the large N10 relay located at the front end of the windshield inside the engine bay???

@DonisGP 4 жыл бұрын

I think it's just the signal. Because they still turn on but goes off if you dont hold it with your hand. So it's just the switch that's in the videos that is bad. Nothing in the dash. At least with mine its isnt

@evelynventura339 6 жыл бұрын

Can someone tell me how to disarm a mercedes switch log? Please

@docselva 4 жыл бұрын

Hi bro. My signal indicator need replacement.. Is the replacement part same for both left and right hand drive car? Mine is Right hand drive. Thanks

@DerFilmgucker 3 жыл бұрын

I would think so, as long as it’s positioned on the left of the steering wheel.

@DerFilmgucker 3 жыл бұрын

I just looked up the part for a 2004 W203 C240. The side question did not come up.

@docselva 3 жыл бұрын

@@DerFilmgucker ok..thank you.. Yes,is on the left hand side of the steering

@Adanarth68 Жыл бұрын

Hello, where can i find or buy that red thing to lock circle?

@Noname-fv4pq 11 ай бұрын

YO tampoco se donde comprarlo, ni se lo que hace.

@huntrichardson 4 жыл бұрын

Got to the 10 mm nut which does not budge even using breaker bar. Totally stuck. Any suggestions?

@badgermilk 3 жыл бұрын

Impact

@mafia6502 4 жыл бұрын

My wiper don't work or the turn signal doesn't either do I have to switch the the turn signal

@AyoScreen_ 4 жыл бұрын

mafia650 my wipers don’t work either how did you ever fix your problem ???

@mafia6502 4 жыл бұрын

@@AyoScreen_ I switched the turn signal

@AyoScreen_ 4 жыл бұрын

What do you mean you switched it ? You bought a another new combination switch ?

@edward3105 3 жыл бұрын

Where did you get the new turn signal " stick" from? I have a similar issue but its on the right signal

@ThingsLike 3 жыл бұрын

ebay, but you can try other vendors like autohausaz, rmeuro, fcpauto - sometimes even the dealership has cheaper prices

@edward3105 3 жыл бұрын

@@ThingsLike Do I need to pay with credit card before getting the packet cuz I dont trust ebay?

@ThingsLike 3 жыл бұрын

@@edward3105 been using ebay for 15 years, never had any serious issues but you can also go to a local car junkyard instead and pick that part yourself. See if you have an auto salvage yard in your area.

@ashleyrowe2945 5 жыл бұрын

Did you disconnect battery first ?

@ThingsLike 5 жыл бұрын

Yes

@buretehudesi 3 жыл бұрын

Hi. my left turn signal swithes on randomly. Do you think its a switch fault?

@ThingsLike 3 жыл бұрын

i'm not 100% sure but maybe the electronics in the turn signal talk have become faulty

@benjiwayne4295 2 жыл бұрын

Unfortunately, it looks absolutely nothing like my C320. At all, but the general concept still helps.

@khalidzahiq3374 3 жыл бұрын

hello friend i have the problem of my 270ml cdi 2004 cranking about 2 seconds and it stops without starting 5 to 7 times without starting i have changed the starter motor and changed the ignition antenna i have checked all the fuse boxes i have found All are going well I have changed the battery and without news but when I connect it with cables with another car working it starts directly. now I do not have to think about any reley that is main! do you know if he has any ??? please help ...

@ThingsLike 3 жыл бұрын

Dear Khalid, I'm not sure what your issue could be. However, an issue with similar symptoms to those you describe occur over here: mbworld.org/forums/c-class-w203/527256-w203-doesn-t-start-does-not-crank-3.html The driver replaced his ECU to resolve the issue

@sedatkizildogan8023 3 ай бұрын

Map sensörü yada diğer adı ile hava akış metre yi temizlettir kızdırma bujilerini kontürol ettir EGR kelebeğini temizlettir mazot filitresini değiştir

@deanwinchester7179 4 жыл бұрын

My mechanic is scared to do this because he thinks the airbag will go off even with the battery unhooked. Is this fear unfounded or actually something to worry about?

@ThingsLike 4 жыл бұрын

ask him what would trigger the airbag to go off if there is no electrical current running through the system

@dilrajbanwait7556 4 жыл бұрын

It will be fine he will just have to disconnect and leave for 15 to 20 mins to allow all copasitors in the vehicle to die down before starting. Once airbag is remove due to the classification it should be put in a strong metal box which is lockable, airbag facing up.

@deanwinchester7179 4 жыл бұрын

He was worried about the airbag having capacitors or something else in it holding charge; then I guess messing with the connectors setting it off or something. Or he was just lazy and didn't want to do it lol. I did end up doing it myself wit no issues :)

@Kman. 4 жыл бұрын

Here's a question for a/one who may have a *SUGGESTION* at least, as two d'ships can't figure this out at all... The turn signals work, but after "X" amount of time, they *STOP* working. No specific amount of clicks on/off...no certain mileage driven, nothing to associate with the *NOT* working of them, *BUT* if you turn the car off and restart it, they begin working again! No code shows up or gets stored to indicate what the issue is. Others on the web also are searching for help.

@KneeKrusher 6 жыл бұрын

Wow....this looks very difficult 😷😷🙃🙃

@sl5311 4 жыл бұрын

Disappointing. Mercedes always so over the top.

@MarlbarO1000 5 жыл бұрын

I know where is The "Problem" why switch is not standin in his position! don't need buy new one or second hand... you just need open Turn signal box 2.screw and change little black clips right to left , and left to right, and it will be like NEW! ;)

@redapple2457 5 жыл бұрын

which clips?

@nsndnabd8640 4 жыл бұрын

what clips?? I have now the problem turn signal not stay in position😪 plss help..