Mercedes E350 Wheel Bearing Replacement - 2014 E350 4Matic W212 time-lapse

Рет қаралды 24,427

Күн бұрын

3x 2014 Mercedes E350 4Matic wheel bearing replacement. Video only. W212 4Matic E350
Mercedes Wheel Bearing: amzn.to/3Ll5pPH
00:00 - intro
00:33 - remove caliper bolts and hang brake caliper
02:00 - remove caliper bracket bolts
03:00 - remove brake rotor
03:18 - remove brake shield
03:44 - remove sensor
04:10 - loosen wishbone suspension bolts/nuts
05:12 - use press tools to separate joints
10:12 - remove knuckle mount bolts at the strut
10:29 - remove axle bolt, push in axle and remove knuckle
11:43 - hang axle with strap to prevent damage
12:15 - attach and use slide hammer to remove part of bearing
14:10 - failed attempt to remove inner bearing race with pullers
15:20 - switch to bearing splitter to remove bearing race
28:55 - press bearing out of knuckle using shop press
34:28 - clean up knuckle and ring a bit
35:50 - press in new bearing to knuckle first
38:17 - press flange into bearing and knuckle assembly
39:20 - close up press in flange
40:30 - install knuckle assembly back onto vehicle
43:36 - tighten and torque components
47:21 reinstall brake shield, caliper bracket and caliper
More information, parts and tools links available on my site here: www.2014mercedesmaintenance.c...
Links may include affiliate links where a commission is collected when purchasing through a link.
#mercedes #mercedesbenzeclass #mercedesbenz #automotive #autorepair #m276
#diy #wheelbearing #howto #4matic #carrepair #w212 #automaintenance

Пікірлер: 37

@gabrieloubre5726 Жыл бұрын

Could have took it off in one rip! !!!love it but I hate when it's dragged out wasting time

@masterimperium4886 Жыл бұрын

Mercedes tech here. I always use die grinder on the inner race that sticks on the hub. Then when I am almost through the race I smack it with big chisel and hammer, it will crack and come off by hand

@mauricem.mcgraw5513 6 ай бұрын

THANK YOU!!! So much for a [COMPLETE] video process. The most irritating things I have experienced with this project. Is one where an individual beings a video and then when the going its complex. They edit and return with a completed project and then back track explaining their way through.

@mattblank7728 5 ай бұрын

Awesome video, ty so much.

@JohnnyP414 7 ай бұрын

For those who are about to watch. Set to 2x speed. Solid vid, but deffo way too much back and forth figuring out best approach.

@Nivlaceel78 3 ай бұрын

thank you for this video. I'm gonna bite the bullet and take it to a shop.

@eagleeagle681 2 ай бұрын

Can you remove the front differential without removing the engine subframe? I have e350 2014 4matic with front humming noise wheel bearing are good and tires. The only thing that is suspected is front differential.

@andresimmons6249 Күн бұрын

Where did you buy your parts & do you know the correct Flange diameter?

@Stefan_Smith Жыл бұрын

Thanks for the video, really helped alot! Quick question, at 36:06 did you install the bearing backwards? Remember that rubber seal that you removed at 29:18? It was facing the front of the knuckle wasn't it?

@Stefan_Smith Жыл бұрын

Followup question, did you get any speed sensor issues?

@brenth7774 10 ай бұрын

Sorry for the late reply, so that was not a seal and was the snap ring, which has to be removed before you can press the bearing out. The bearing was installed correctly however, not backwards.

@eladioredin2124 10 ай бұрын

Agony! You first need the right tools!

@brenth7774 10 ай бұрын

yes, you'll need some specific tools to do this replacement.

@danailignatov3845 Жыл бұрын

How much nM at the center bolt? And at the other too?

@Stefan_Smith Жыл бұрын

Waiting on this reply. I just recently completed my bearing and an axle replacement due to torn boot. Was hard to determine which was the issue as it is my sister's w212 4matic. Even though we put all 4 wheels in the air and let coast; the noise was coming from closer to engine side, as well as near the hub; it was making a hideous noise; both were bad.. 1 probably led to the other failing.. Anyways, hope the bolt wasn't torque to yield, cause the axle came with a new hex bolt, I put the old torx back on as it looked to be in good condition, torqued it until I basically had to put my body weight on it. 🤷🏾‍♂️

@Manuel-xy7un Жыл бұрын

what are the torque specs for the axel bolt ??

@ovina5411 11 ай бұрын

160nm then loosen, 120nm then 90°. Basically about 310ft lbs. 😂

@gabrieloubre5726 Жыл бұрын

I'm lost on the process taken, please let me know why not use the press off the top? ??the knuckle had to come off anyway! !!guess because the hub is getting reused but tooooooooo much work for such a cheap part???

@Stefan_Smith Жыл бұрын

Now tell me how a press helps anyone outside a shop? Oh I guess youtube is for shop professionals as well? Idk why I ever held you guys to such a high standard, assuming you're the mechanic, you shouldn't be the target audience for a bearing replacement. I'm a home wrencher, I'm glad he didn't use the press, as I dont have 1. He showed both which was great, if I had space in my garage, I'd probably buy a press, as they are really cheap, but why buy something you'll probably use once a year?

@gabrieloubre5726 Жыл бұрын

Why not use the press on the knuckle initially? ??must be charging Alot to make for time

@Stefan_Smith Жыл бұрын

I think he was showing it can be done without, for those of use who don't have a press.

@brenth7774 10 ай бұрын

I don't have the on-vehicle press, just have my own press from harbor freight. I'm not a shop, it's my own vehicle.

@AnontheGOAT Жыл бұрын

When replacing the bearing, does the race have to replaced as well?

@brenth7774 Жыл бұрын

Yea, it’s a one piece bearing.

@AnontheGOAT Жыл бұрын

@@brenth7774 hmm, race is actually part of the hub right? So if I have a worn bearing, i should just skip replacing the hub and just press the bearing out of the knuckle?

@brenth7774 Жыл бұрын

@@AnontheGOAT No, the whole bearing presses onto the hub, or you're pressing the hub into the bearing. When you say hub, I assume you're meaning the flange where the wheel bolts to right? 38:15 is what has to be done. At 14:10 is where I removed the race from the flange. That race is part of the one-piece bearing however, I used the slide hammer to pull it out. Hope that makes sense.

@AnontheGOAT Жыл бұрын

@@brenth7774 So I have an w212 4matic. I think my front right bearing is shot. I ordered one to replace it - but it’s the one you did at 38:00. I didn’t order the race as I wasn’t aware of it needing to be replaced if a bearing goes bad. So my question is, why did replace the race and the bearing instead of just the bearing?

@brenth7774 Жыл бұрын

nah so that's actually just one piece bearing, it came apart and left the race on the flange - there's no separate race. You'll need to press it in that order though to avoid damaging the bearing. So press into the knuckle first from the outer race, then support the inner race while you press the hub in. hope that helps.

@Jakkson253FamilyFirst Жыл бұрын

Thats A Whole Lotta Work ! 😅 Instead Of Taking Everything Off Couldnt Mercedes Just Have Da Whole Wheel Bearing Component Assembly Come On And Off For An Easier Replacement ???? Most Of His Time Went Towards Taking Off Da Bearings Anyways Great Mechanical Job 🤙

@juicebox22a 6 ай бұрын

Many People purchase the kit with the new hubs & new bearings for this reason.