Great video bud! You're awesome. Like everyone else I too got stuck at the long 10mm bit. Ain't nobody have a 6inch 10mm bit lying around so I had to stop work midway and put a special order in for a 6 inch 10mm . I think it might be worthwhile to mention the socket sizes in the description. Thanks for your work.
@kevinle7976 Жыл бұрын
Thank you, I fixed my car without going to the garage ❤❤❤🎉🎉🎉
@transanity Жыл бұрын
Great video! Straight to the point and easy to view what you are doing. Thanks!
@jackgross3140 Жыл бұрын
Thank you for the positive feedback 😁
@nicolassaglia83168 ай бұрын
Thank you man ❤
@toogangzАй бұрын
Hey thanks for the great video! Just wanted to check if a 13cm / 5inch deep socket is deep enough?
@jackgross3140Ай бұрын
That should be fine 👍
@turatura8516 Жыл бұрын
Thanks 🙏🤲
@duyphucnguyen1053 Жыл бұрын
merci beaucoup
@Newaark763 жыл бұрын
Thanks for the video. I have an issue : When I put it back on, the plastic cover that goes over the wheel doesn't fit right, there's a gap between the panel and the plastic part. How could I fix this ?
@jackgross31403 жыл бұрын
Thankyou for the feedback! You may need to use some new double sided tape to re fix the arch trim back on after removal
@devontesnellen56632 жыл бұрын
Hey Great Video! I’m trying to do this for a friend but I’m having a problem finding that deep of a socket! How long is that thing?lol
@jackgross31402 жыл бұрын
Hi thank you for the feedback!😁 the socket is from snap on I can’t remember the exact size though unfortunately but it’s around 4 inches deep!
@floydnejad1853 жыл бұрын
Hi mate, how do I find a 10mm deep socket? I searched everywhere i.e. Halfords etc. thanks
@jackgross31403 жыл бұрын
Hi bud, my super deep socket was from snap on, I’ve not heard of any other companies making these sockets but there are ways around it, you can tape 2 deep 10mm sockets together and it will work fine, the nuts aren’t done up very tight so it should still undo it fine
@chozusmakavelli2 жыл бұрын
@@jackgross3140 ah ha!! Excellent idea with the 2 10mm take I together. I'm working on a slightly newer shape, theres no nut on bumper in the wheel arch, there was an 8m horizontal half way down the bumper, and the lights seem completely different to remove, I'll keep plucking away.
@yauck13 жыл бұрын
what's the nut size and how long the socket has to be in order to take it off at 1:40 and 4:15?
@jackgross31403 жыл бұрын
Both 10mm sockets, the one at 4:15 you will need an extra deep socket
@yauck13 жыл бұрын
@@jackgross3140 how deep at least? Thanks!
@jackgross31403 жыл бұрын
@@yauck1 it’s 4 inches deep approximately I used the snap on 1/4 inch extra deep 10mm socket
@linocavallaro64946 ай бұрын
hi, please can you tell me how i can remove plastic arc on rear fender completely ? after the middle part is it fixed with a double-sided glue is it right? many thanks
@jackgross31406 ай бұрын
Just double sided tape for the rest of it, be careful not to bend the trim
@jackgross31406 ай бұрын
Apply pressure outwards and wiggle up and down at the same time and the tape will be released