How to replace the fender boot/grommet on the power antenna on a Mercedes Benz R129 500sl..others similar follow me on twitter / fupabox
Пікірлер: 26
@hammondfan21853 жыл бұрын
Thanks for this video. For mine, I did have to remove the remnants of my old lower grommet from the inside, but was able to avoid the disconnect of the antenna unit and complete removal of the well carpet by pushing the lower part through from the outside enough to get that lip below the fender, then snap on the upper.
@mississippirider17478 ай бұрын
Thanks for the video. I just bought an r129 with a broken antenna and didn't know what to expect.
@robertm719710 жыл бұрын
Very helpful, thanks for taking the time. I can add that it is easier to install the lower grommet from outside the car, rather than pushing it in from inside. Good call to inspect the hydraulics while the trim is off. Keep up the good work!
@mikejohn00884 жыл бұрын
Thanks pal....this was of help to me as I did not know I needed both lower and upper pieces. Thanks too for Robert as I'll make the installation of the lower unit from outside the car.
@petesky793 жыл бұрын
Dude thanks for the clear instructions, saved me $ from taking it to the mechanic.
@fupabox3 жыл бұрын
Glad it helped
@thaddeauscaldwell71014 жыл бұрын
Thank you for another great video for the R129. I had to replace the outer antenna seal on one of my R129's because it was cracked and some "Chimps" lol , had the inner seal on the antenna shaft and wasn't through the quarter panel hole , as its suppose to be . Fixing small details , is a great difference. Thanks again. Best Regards
@fupabox4 жыл бұрын
yup..beware of chimps . They screw up more than they fix. :) Fixing the little things is pretty satisfying .
@denizatila2 жыл бұрын
that helped a lot to understand how to assamble the rubber parts, thank you indeed
@fupabox2 жыл бұрын
very welcome . Glad it helped
@njoeandjen5 ай бұрын
Great Job.
@HighFidelityFox11 ай бұрын
Thanks for the video, I was wondering how to install the grommets. What year is this? I have a 99 and the boot liner had a CD Changer that had to be removed. Also, there was a hydraulic cylinder and a bunch of hoses infront of the antenna assembly, which also had to be removed - yet yours was right there easy access
@edwardrivera2067 жыл бұрын
Awesome 😃
@chipperJones388 Жыл бұрын
Thank you buddy!
@fupabox Жыл бұрын
Very welcome 🙏
@Lakitu6410 жыл бұрын
Hey bud just wanted to say thanks for the help wondering if u have a video on the catalytic converter I think mine is going out I have a rattle under my car and acceleration was. Never that great I also have a intermittent starting problem any ideas would b so appreciated
@robinarmstrong27286 жыл бұрын
Just when I was getting ready to do this,Viola,it comes up on the Tube...Thanks
@klausstegmann50345 жыл бұрын
sl r 129 🤗🍂 ein danke schön, und ein lieben gruß,
@charlestaylor1010 Жыл бұрын
👍👍
@jab38794 жыл бұрын
does anyone know what size that philips screw is holding the antenna in place? stripped it, need new one. thanks
@mikejohn00884 жыл бұрын
Are there two size outer grommets? The one I purchased does not completely cover the opening.
@fupabox4 жыл бұрын
there shouldn't be ,unless the part was changed on different years
@mikejohn00884 жыл бұрын
Ya, one grommet set is larger for the "ball top" antenna. It's 42mm long vs. the std. that is 34mm.
@kedocom10 жыл бұрын
my outer grommet split in two ..... oh those little plastic thangs!
@timonterey8 жыл бұрын
Thanks. This video is useful, but it was difficult to understand because (1) the black goop concealed how the parts fit together to start with; (2) the camera was wobbly (sometimes the action was even off screen); and (3) there was too much manual fumbling that could be edited out to relieve viewers of wasted time. I hope this comment is helpful.