Mercedes W211 Thrust Arm Replacement

  Рет қаралды 11,540

DCF Garage

DCF Garage

2 жыл бұрын

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/ @dcfgarage
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Would like to support the channel?
www.paypal.me/dcfgarage13
/ dcfgarage
Disclaimer
The information contained in this video is provided "as is", and should be used for directional purposes. Always follow safety procedures and understand the legal implications of any modifications you might make to your vehicle. Several factors beyond my control might change the information provided in this video. I do my best to provide the most accurate and complete information possible, however, I shall not take any liability for property damage and injury occurred as a result of any information contained in this video. Use it at your own risk. No information contained in this video shall create any implied or expressed warranty, or liability.

Пікірлер: 11
@ooooooo6038
@ooooooo6038 2 жыл бұрын
Great detailed video. one tip though, torque the thrust arm with the wheels on the surface so it’s sitting right when the weight is on it, otherwise it will be always in stress and you’ll go through bushings really easy.
@dcfgarage
@dcfgarage 2 жыл бұрын
Good point. I’ll retorque them one of these days
@lcervantes8505
@lcervantes8505 5 ай бұрын
Nice! 21mm is key to the heart of merc suspension.
@drewprof
@drewprof Жыл бұрын
You may want to check when to tighten the thrust arm on the chassis. I believe it must be done under load, in other words, tires on ground.
@dcfgarage
@dcfgarage Жыл бұрын
U are absolutely right! Doing the way I did might cause premature wear
@lovera3878
@lovera3878 2 жыл бұрын
Good video. I am replacing all the components of the passenger side. the driver side was done a few months ago by someone else. It looks easy enough for me. Tie rods as well. I watched your video. As someone pointed out I torque the nuts once I put weight on the wheel.
@dcfgarage
@dcfgarage 2 жыл бұрын
Thanks! Good luck
@brunowest5027
@brunowest5027 2 жыл бұрын
Thank you!!!
@lcervantes8505
@lcervantes8505 5 ай бұрын
Big thrust arm nut 80Nm+120'. Torque should be under load or you'll tear rubber parts , drive weird, and get noises.
@dcfgarage
@dcfgarage 5 ай бұрын
Thanks for the tip!
Mercedes Thrust arm replacement C class/E class/S class/CLS
25:03
Helping Hand Auto Repair
Рет қаралды 78 М.
A clash of kindness and indifference #shorts
00:17
Fabiosa Best Lifehacks
Рет қаралды 13 МЛН
3M❤️ #thankyou #shorts
00:16
ウエスP -Mr Uekusa- Wes-P
Рет қаралды 13 МЛН
DO YOU HAVE FRIENDS LIKE THIS?
00:17
dednahype
Рет қаралды 81 МЛН
Final muy increíble 😱
00:46
Juan De Dios Pantoja 2
Рет қаралды 50 МЛН
Mercedes W211 Lower Control Arm Replacement
18:40
Car D. Ologist
Рет қаралды 124 М.
Fix Your Mercedes-Benz Sway Bar Link
13:35
Raymond Urias
Рет қаралды 165 М.
Mercedes Upper Control Arm Replacement
16:51
DCF Garage
Рет қаралды 18 М.
MERCEDES C230 TORQUE STRUT (UPPER CONTROL ARM) REPLACEMENT
13:00
F.S. Detail Garage
Рет қаралды 28 М.
Replacing the Inner Tie Rods on my W211 Mercedes
12:16
DCF Garage
Рет қаралды 27 М.
❗Он Застрял В Машине #shorts
0:22
ORNAUD
Рет қаралды 872 М.
Respect🥺
0:35
Armada Motors
Рет қаралды 2,9 МЛН
Respect🥺
0:35
Armada Motors
Рет қаралды 2,9 МЛН