My 2012 262c cat skid steer drive joy stick, when I use it for a full minute without letting it drop in nuteural, the machine starts slowing down and eventually stops. Drop it in nuteural and things work fine for another minutes and then same thing. What's going on??

I have a 2015 year 299D Cat xps high flow two speed - it will not go into high gear? and cat service dept. said I have to buy a wire harness that would cost $3,000 to 4,000 dollars. But I replace the joy stick that didn't fix the problem ( first they said it was the joy stick -- Not) . Back to the wire harness would you think that would be the problem. I did order a wire dia. Please reply it would be really appreciate

I JUST GOT 2014 CATERPILAR 242D TURBO 2 SPEED . WHICH HAS NO DISPLAY WORKING .. I TOOK THE RISK TO BUY LIKE THAT WITHOUT EVEN POSSIBILITY TO CHECK THE HOURS ON THE MEETER .. BUT IS TIGHT MACHINE AND RUN LIKE NEW . WHAT COULD BE THE POSSIBLE TROUBLE WITH THE COLOR DISPLAY NOT WORKING AT ALL ... ?? THANKS STAN

MORE VIDEOS OF DALE!

Dave I have a 1997 L's 190 new Holland skidsteer and I would like to ask how do I remove the fuel tank?

Can I hose down the engine compartment and under the cab or is that not recommended? I don’t want to create any electrical problems

I have a Cat 247, 2000 model, rarely the left side will stop. I can rev eng up and jiggle the joy stick and it will start again. done this about 3 times in 50 hours, any ideas?

Hi there please let me know how to I turn on system heater my machine.I has bought it summer but not check system heater,I was wondering if it has switch to turn on the heating?

How do I locate the bucket position sensor on 247, where is it and what does it look like.

Have 216b and was moving along hit a bump and breaks locked up. Then the break light was flashing but couldn’t the arm arm light was on had to plug in seat belt but break still locked and can’t release break by pushing switch. Now when tried to start unit all light go off when arms down and you can turn break off but no start nothing. Has power from battery. Getting ready to check fuses.

What about wiring? Why do I keep going through harnesses and ac lines?

Working on a 426B Backhoe cat 🐈 1997 Have a transmission problem when machine is running it seems to create back pressure and pushes transmission fluid up and out filler tube it seemed to have the correct amount of fluid come out when I drained it. Around 2-1/2 gallons, it seems to of only taken 2 maybe 2-12 quart and if I let it run it seems to backup or climb backup the tube. Any help would be great thanks 🤔🙃

On a 226B, I am losing oil at a concerning rate through the dip stick??

Hi I have a 257b how do you replace the hydraulic fluid with new

I have a caterpillar 289c my instruments and fuel gauge are not working do you have a solution for me

What is the best way to change the dpf filter on a 259d track skid steer?

fuel gauge doesn't work on a 226 B skid steer how do I check the fuel level

I have a CAT 279C that turns on the warning light and locks the parking brake when going in reverse. What could be my problem?

I have a 2005 cat 257b skid steer when I unlock the safety to travel it locks the breaks and want move. What do I need to check

Good Morning I have a cat 277c that won’t turn right. I changed both speed sensors. Any idea what could be. Ty

whats up with Cat skid steer parking brake buttons problems seems like it's a common problem I have came across 3 myself that have had this issue.

A Caterpillar Track Skid Steer 279C suddenly stopped moving, including the work tools, engine starts fine. It provides an error 2471-3 which ti my understanding is for the cab door switch, the with bypass was hook up, didn't work; the wires to the ECM do have continuity Advice on addressing this issue will be appreciated

T190. Had bad battery. Changed. New battery went bad. Changed alternator & battery. Runs great. Control panel won't light. Arms & tracks locked. Has 2600hr. Dealer hasn't been able to help at this time 😂. Changed solenoids & fuses. Arm sensor is good Would be so grateful for any direction to look. Please help in Florida 😁

I replaced the batteries but I’m not getting power into the cab

how do I flip cab open or remove

i have a 763 bobcat and it dont have the power it use the have when i push the drive handles forward it bogs down and the belt make nose it also does it when i moving and try the rase or lower the bucket. i do know my drive motor on the left leaks a tiny bit.. i been useing r&o hydralic fluid.. i changed the filter a few months ago and chande hydralic fluid

How to change the RHS joystick on a 257b bobcat

this is about the radio in a backhoe why does it shut off while driving/ raising rpms

Hello I have a question on 262C and the 262C series 2 is there a significant difference between them?

I have 248 hi flo engine runs,cooling fan works,no steer no lift please help. thanks ,rshirk

My CAT 303.5 don’t start. Hoy i release the brakes to put it in a tow truck?

I work on several Cats and John Deere A/C systems. Right now I am working on a 450F backhoe, can not find the receiver dryer and I believe the orifice tube is in the drier. Is there any site I can reference schematics for several models of Cats?

The Parking Brake on my 2008 256C Skid Steer keeps coming on automatically -- preventing me from moving more than a few feet at a time. ( I had allowed the hydraulic fluid level to drop down below the "add line", -- and while the bucket and grapple continued to work, -- I assumed that was the cause of the Parking Brake problem. -- I just had enough Hydo Advance 10 fuild on hand to bring it up to the lower mark on the sight glass, but that hasn't solved the problem.) I can only move a few feet at a time -- although when the engine is reved-up it will move a little further before automatically setting again. Is it possible that a "code" may need to be reset ? -- and if so, how would I do that ? Any help would be appreciated.

I have a 232b caterpillar skid steer, the parking breake do not release, I would appreciate if somebody can help

my cat d9h dozer on over heating

They want you to go to the dealer for everything me and 2 other guys changed both tracks on a 287b in 4 hours and they wanted 9 thousand dollars to do it and the hydraulic lines start breaking when they get old so if you have to pay them 1000 dollars to change one every time one breaks you might as well buy a new machine with good lines😂

Cat 246c what problem engine failior.malfunction

cat 226b flashing park and seat belt signs

the parking won't release. why?

My226 cat skidsteer will not disengage.

Hey dale

Hey dale