Please update your MIDI Captain device to FW3.5 to solve the latency problem of USB midi control Check www.paintaudio.com for any info. And we also released the 1 2 4 6 switches MIDI Captain Serials. Thank you always!
Пікірлер: 34
@leopoldoinnecco59243 ай бұрын
Amazing !!! Same issue I had with Harley Benton mp100, the difference being they do not offer support for it … just ordered my midi captain after this video !
@stephenpertesis77104 ай бұрын
Looking forward to buy once there is a tutorial video for MAC firmware update process. There are too many people claiming "brick" upon attempting process. Yes, I've already read the directions, but you need a video. In my experience, if you misconstrue ANY LITTLE STEP in a computer process, the entire process can break things including my patience. So, you have more purchases once that video is released.
@leopoldoinnecco59243 ай бұрын
Hi there... I followed the instructions to put the ne files inside the device but I get an error daying some files can't be read / copied... tried quite a few times... using Mac
@Clive0072 ай бұрын
If slot B is already on then surely you have to press switch 2 twice to get the Midi Captain and the KPP in sync? How does the Midi Captain know the on/off state of the KPPs modules?
@kneggo48875 ай бұрын
Hey Wilson! When will the super mode arrive for the midi captain with 10 switches? Looking forward!
@Wilson-PaintAudio5 ай бұрын
Yes. It will for sure. Already 80% done.
@EaslerMedia5 ай бұрын
My MIDI Captain seemed great but came up with an error that seemed to make it bricked after a couple of days of use. I sent an email with a picture of how. Hoping for a response.
@Wilson-PaintAudio5 ай бұрын
Don't worry, MIDI Captain can always be recovered. You can do the update process with the FW3.5 which can be downloaded from paintaudio.com to recover it. Will reply your email soon.
@YoRonLucas5 ай бұрын
I also have my MIDI Captain bricked. I was configuring a preset in Geek Mode, and then it came up with an error. Since then I cannot use it. I sent a screenshot to Paint Audio via their webpage but haven't heard back. I've reapplied the current firmware (3.04), but it did not resolve the issue.
@EaslerMedia5 ай бұрын
@@YoRonLucas I haven't been able to get mine to be recognized as a disk after this happened. It just loads with the error. Hoping to have some advice soon.
Hello does the tuner mode appear on the lcd screen as well or does it only activate the LED’s on the KPP?
@Wilson-PaintAudioАй бұрын
So far the tuner control is only for tuning on the tuner LED of KPP. A plan is to add a tuner LCD mode on the controller with note display.
@nicor8029Ай бұрын
@@Wilson-PaintAudio super thanks for the fast reply - that would be a great addition, as the LED on the KPP are too minimalist
@lufeportinari5 ай бұрын
Hi! Great news! Can I install this update in the midi commander too?
@Wilson-PaintAudio5 ай бұрын
MIDI Commander is using different hardware platform😂
@Ribeirogt5 ай бұрын
E o da ampero 2 quando sairá?
@vsestudio54135 ай бұрын
UPDATE FOR BOSS GT 1000 CORE WHEN IT COMES OUT
@michaelkaufmann27295 ай бұрын
stuttering volume, wah etc with expression pedals
@sevecornago37235 ай бұрын
Thanks Wilson fantastic: update Supermode Midi Captain?
@EaslerMedia5 ай бұрын
Not sure where your reply about the USB cable went but that was the issue! I'm pretty surprised since it was powering on over usb and everything just with an error. That worked! Ran the firmware again and all was good. Maybe the suspect USB caused it to brick to begin with.