I have try all Snap on würt ,Bessey ,stanley not even on this legue ,old irwin Gilbow .Midwest are absolutely the best for me they effortless and comfortable and bloody sharp .👍🏼

great review. I would like to share a crazy awesome discovery I had experienced earlier. I have used all snips available on the market, and have found Midwest to be the best. now i have ruined some Midwest snips by cutting things that they are not designed to cut, hardened spring wire for example. because they are already ruined I figured what could be the harm in trying to sharpen them. so after a quick shot on the 6 inch disc sander, I reassembled them, AND HOLY COW, THEY CUT EVEN BETTER THAN OFF THE SHELF!!!!! I also tried them on some crazy thick stainless steel, you know the kind that ruins snips, and it did great! I realize I've removed the small serrations but did not notice any slippage, JUST SMOOTH, CONTROLLED, FLAWLESS, BUTTERY CUTS. I was excited at first, then I got kinda upset, because for 20 years now I've spent my hard earned money on the best tool that I know about, and with a quick zap I have improved the snips by more than say 50 percent. how many have I thrown away. THANX, PLEASE TRY IT, SHARE IT, THE WORLD SHOULD KNOW.

Thank you for using those two metal gauges as your metric. 26 gauge is common snapped together flue ventilation till it hits the double walled b vent pipe on a gas furnace. And most gas furnaces need to have one side or the other cut out and they're usually constructed in 22 gauge metal. Midwest are the best. They can cut wrapping paper clean. Seriously. They can cut thin wrapping paper with out folding it and tearing it.

Midwest Snips are THE BEST period the reds the middle one in the vid are my go to ones, they work good also on 16 gauge metal you might even be able to cut 14 gauge but will require a lot more strength

Thanks for the review, just bought some midwest snips and they are miles better than my harbor freight ones

The upright left cut or 90° snips are actually only rated for 24 gauge metal

I have them and like them. Just curious where other people rate them compared to Malco's or Milwaukee's ?

Even after my questioning of the review because of the misadjusted competitors snips, I went ahead and bought the Midwest brand snips. So far I have been using them only on thin aluminum, an easy job for them, but so far I like them. I will add, just like his straight snips, on the set I purchased the pivot bolt is not inset and is just like the competitors. All 3 snips I purchased don't have the inset pivot bolt. I got them on Amazon, the numbers are MWT-6716 suffix S, L, or R. If the pivot bolt is important to you, this model # is not what you want.

Good review, Sir! I never really thought about why other snips would separate or "sandwich" when cutting through some materials. Makes perfect sense though when you explain it. Before I always just shook it off as "the material is just to thick", but now I know it's because I bought sh#t tools. It's one of those "ah-ha" moments that leaves you relieved to have a solution, regardless of felling like a dumb a&# because you didn't figure it out on your own. Thank you, Sir! Another great video!

After watching this video a few days ago I got me a pair of Wiss red and Midwest reds. Doing a 90k custom job and obviously cutting a lot of holes in some tight spots. Both reds are BRAND NEW. Started with the Wiss pair this morning till lunch and Midwest till the end of the day 12 hours....Midwest cut as easily as the Wiss did, UMMMMMM, WHAT? Yeah, even after 5 hrs of cutting and then switching over to the Midwest's the cuts seemed near as easy with all the earlier fatigue. Let a coworker use them and after 4 minutes he was on the Amazon site ordering a set of Midwest. Today I switched up, Midwest in the morning and Wiss this afternoon. Midwest wins. But, not everyone is designed the same. I have large hands and don't choke up on the handles much, cutting a lot of holes I like big bites. Did I count the lineal feet cut with either? No. All I know for me is that everytime I pick up the Midwest pair I'm happier and so are my coworkers when I set them down and they drift off someplace.

I love muy Midwest aviation snip 2 years and still like new. The Best snip I ever had 👍👍

Thanks for the reviews I had no idea on most of the stuff you review. Can you do one on an aircat 1150 air gun? They're supposed to be quiet, agronomic, and more powerful then IR for like half the price.

I'd love to see you review Channellock aviation snips.

Which snip would you recommend for cutting straight lines thru 3 feet of metal ? I'm going to be getting some diamond plate sheets 21 gauge I'm going to cut and I need a very straight cut.

The 90 degree ones are only rated to 24 gauge and thinner. Not 18.

i just cut 16ga today with my old wiss ones...lol

Ok review I’m a metal framer in the union and 18 g isn’t that thick you can but wiss snips at Home Depot and it will cut threw 18 g so saying it’s impossible so saying store snips won’t cut threw 18g is a lie Milwaukee will also cut threw

wow what a difference between two snips my snips... always failed cut edge of everything ..... I should buy those ..

Is there a difference between aviator snips and tin snips

The last Midwest snips I purchased it literally broke in half as I was making a cut on a 18 gauge sheet metal. Now I only buy german products.

wiss and stanley both thread the cutting heads and use a lock nut, its nothing 'special' shoulve have compared them with the standard than some lennox

Those competitor snips look like they're not adjusted properly. Tighten them to the correct amount and try again.

Why can't you get these on Amazon? Where you get them?

I have been in the HVAC industry for a very very long time I have tried literally every brand of snips from every supplier and every wholesaler as well the problem with most of the better quality Snips is the spring gets too weak way too fast rendering the Snips useless the blades usually last it's the spring thanks gets weak way too fast and trying to get warranty for these products is a pain in the butt even from Midwest and for the price point of their extra hard snips it's a ridiculous amount of price gouging for just forged metal die cast tool which cost next to nothing to make

Hi whats you feedback on snap on snips ?

ya... i need one!!!!

NICE TRY. You can see him hold lose the store brands belt, and the promoted brand he holds it closer and tighter not allowing the snips to twist.