After 7 years the door seal of my Miele WDA110 washing machine needs replacement. A suitable compatible, costing 1/5th of an original was ordered. The process of replacement is shown in this video.
Пікірлер: 24
@Specigen2 жыл бұрын
Thank you for very well made, detailed and accurate instructions. No nonsense. Pure to the bone. The best I have seen.
@AmstelBright Жыл бұрын
Thank you, David. I used the same procedure for my Miele 5965, which has a virtually identical seal (except it has a sensor next to the hose on top, so some additional fiddling is required). This video helped a lot!
@geertlampen2068 Жыл бұрын
I used this on my Miele W1913. Removing the front panel was a bit different and I saw how that’s done on another YT guide with a fella drinking a lot of wine 😅. But the replacing of the seal was spot on and now my Miele doesn’t leak anymore. Many thanks 🎉
@gigglekuh7640 Жыл бұрын
Thanks so much. I just used this technique for a Miele W5741. It worked perfectly!
@calle1976 Жыл бұрын
Thanx for a super useful video! Replaced my seal in no time, thanx to you!
@AdventuresandLifestyle Жыл бұрын
Many thanks. From a previous Samsung machine I knew what was involved but cant beat a refresher ! Perfect video 👍😊
@nikrite8432 Жыл бұрын
Verywell done...saved me a fortune
@paulbaillie49274 ай бұрын
You absolute legend sir, just done the repair, you made it easy. Huge thanks!!
@david4bs2 жыл бұрын
I have always found the compatibles perfectly serviceable so I use them. In this instance I bought the least expensive one I could find and it's working as well as the original.
@nikmagnus86264 ай бұрын
Thanks so much for this video. I used it to help me replace the seal on my w1 Miele.
@joergbcat3675 Жыл бұрын
Thanks David,perfect
@iamsailingau10 ай бұрын
You are my champion, thanks for the video. Job Done, only with your help!!
@llithrig Жыл бұрын
Many thanks for the video. I made some notes on my W304 Premier seal replacement. The black inlet hose is connected to a white plastic 'T' piece which is fitted from inside the seal, so if this is the case you must pull the hose off this plastic tube rather than with it. The seal clamp screw was fitted on the right of the drum so I didn't need to remove the door lock. Clean the black scum from inside the drum outer casing before fitting the seal. Replace the T piece from inside the seal and place the clamp over the seal before fitting around the drum casing and re-connecting the black inlet hose. I used a box spanner to tighten the clamp. Don't over tighten. I cleaned to door seal rim on the front panel with a cloth & IPA as there was residual rubber on the rim. Make sure that the top plastic lugs on the front panel are fully seated. Check that the centre bolt hole is fully exposed before attempting to screw this bolt in otherwise you will probably cross-thread both the bolt and the two screws at the bottom of the panel. Before fitting the outer part of the seal, hold the door lock in place from inside the panel to correctly thread the door lock screws. Make sure that the drum rotates before fitting the outer part of the seal to the front panel. I cleaned to outer wire clamp carefully with a Scotchbrite pad to remove any rubber. I pressed the wire firmly into the outer seal groove starting around the hinge area. This held it in place whilst I used the screwdriver in a reverse sweeping action from around 11 o-clock down to the spring to pop the rest of the wire in place.
@MsLincos Жыл бұрын
Thanks David!🙂
@user-bq5er3jj7g11 ай бұрын
Very helpful, thank you.
@philipsfjp Жыл бұрын
Very helpful, thanks!
@richardc30449 ай бұрын
Exceed video for replacing the seal, in my case problem wasn’t the seal but a badly distorted steel drum which I have vigorously reshaped with a mallet so it doesn’t foul the seal.Will try it out tomorrow??
@3george1362 жыл бұрын
Is there a particular need to use an original door seal - or what's your view on a compatible one best sourced from ?
@mattiasnygren413411 ай бұрын
Thanks for the video! One question, why do I have to replace the door lock release handle?
@david4bs11 ай бұрын
The door lock release is attached to the front panel. It has to be unscrewed so the front panel can be freely removed without being attached to the door lock or anything else.
@mattiasnygren413411 ай бұрын
@@david4bs but cant I just re-attach the old one?
@mattiasnygren413411 ай бұрын
I used the door lock release handle to open the door. Now the d*mm door won’t lock itself. Any ideas? Thank you 🙏🏻
@david4bs11 ай бұрын
@@mattiasnygren4134 Yes of course you can! By 'replace' I mean to 'put back where it came from'. Not buy a new one!
@david4bs11 ай бұрын
@@mattiasnygren4134 No, I don't know why. However, it's a simple setup in practice which either works or doesn't. It's possible that it hasn't been replaced properly or it's been damaged.