Milwaukee Impact Driver | How Do I Get That Broken Bit Out???

Рет қаралды 62,927

3 жыл бұрын

Trying to remove a broken driver bit from inside the chuck of a Milwaukee Impact Driver. Can I get my bits out?
MORE VIDS
My Top 5 18v Makita • My TOP 5 Makita 18v Co...
My Top 5 36v (18v x2) Makita • My TOP 5 Makita 36v Co...
Homemade Hot Tub • How to Build a Hot Tub...
MY AMAZON STORE www.amazon.com/shop/toolsstuff
My main tool channel: / toolsstuff
Any above links may or may not be affiliate links.
#Milwaukee
#ToolsandStuff
#BuildsandStuff

Пікірлер: 44

@AntonioClaudioMichael 3 жыл бұрын

Dang so many tries in first few minutes I give you props for sticking with it

@AntonioClaudioMichael 3 жыл бұрын

Nice work with the persistence and getting it out

@EnnTomi1 3 жыл бұрын

You can replace that anvils head easily anyway. I would like to try one of those wrench style with 1/4 inch socket, give it more use.

@ledgerwilliams8127 3 жыл бұрын

I have fixed this problem in the past with a strong magnet.

@Elsanta666 3 жыл бұрын

Happened to me more than once, best way, put the sleeve/chuck on a vice hit the trigger foward reverse pull the sleeve and is that easy

@AntonioClaudioMichael 3 жыл бұрын

Great video

@christiansantos8904 3 жыл бұрын

You drill like an 1/8", then increasingly larger diameter bit, until a 7/32, or the closest you can get to RIGHT before a 1/4", you drill the bit out, with as much precision as job site conditions will allow you. Use some needle nose or linemans'. And it'll come out. Takes a couple minutes. Did it today with the m18 Fuel impact and the m12 Fuel Hammer Drill on.....my dogs life. ⚡🤙

@herbo4003 18 күн бұрын

Post a video

@AceSolomon94 3 жыл бұрын

The bits won't come out unless you pull the collet upwards from its sitted position.

@paulmason6378 3 жыл бұрын

Super glue on the end of a round bar works !

@rizzasteicke5190 2 жыл бұрын

I tried that… you bet I just superglued it in there 😂

@ceeweedsl Жыл бұрын

@@rizzasteicke5190 Yea, don't do the superglue. Too likely to make things worse.

@alexbenson5883 3 жыл бұрын

watched a few of these after i fixed one of my buddy's i actually took the head all the way off and took out the bit holder part of it and hammered the side of the top and it slowly worked itself out enough to were i can pry up and pull it out with some pliers but anyways just wanted to complement you on how u did that with a magnet you should see some of the other videos on here for stuck broken bit absolutely horrible but this one was great

@BuildsStuff 3 жыл бұрын

Cheers

@steveramos1452 3 жыл бұрын

Milwaukee chucks either keep it or lose it.

@nuclearexplosion5841 3 жыл бұрын

Try holding the collet open with the magnet

@keithseagle216 2 жыл бұрын

Or just use super glue! I appreciate the video but I was able to get mine by putting a small drop of superglue on both side waiting 15 minutes for them to dry, pressing together and pulling the broken part out. Worth a try!

@cjgalindo6241 10 ай бұрын

This won't work, tried it

@doctorlefthandthread 2 жыл бұрын

I had this issue and replaced the anvil I just couldn't get it out

@mikemaben7485 Жыл бұрын

U cld always remove snap ring washer spring collar and than detent ballbearings or beat on it some more lol

@BuildsStuff Жыл бұрын

YOU COULD always miss the point EL OH EL

@michaelfairchild 3 жыл бұрын

Hikoki light is not a flaw. Its an energy saving feature xD

@philhines 3 жыл бұрын

Y u no dismantle the chuck?

@pro.gurpreetsingh3219 2 жыл бұрын

Good

@pangallie 3 жыл бұрын

Pull back collet,remove c clip, washer and spring. Think that's supposed to work. 🤔

@BuildsStuff 3 жыл бұрын

That was what I intended to try first. Have you ever tried to do it? I could barely see the clip to remove it. I figured if I managed to pull that apart I would possibly never get it back together, or would bugger the retention clip. So I tried everything to avoid having to pull that chuck apart. If I had a patreon I could have got all the input from everybody first and we could have gone through it one by one... I am thinking about Patreon, but need to do a bit more research. I already have a Patreon for my other YT channel, but it doesn't do very well. So many people said they would do it, until I actually launched it, then they all went quiet. Hopefully one day we will get something up and running.

@pangallie 3 жыл бұрын

Didn't actually do it myself but it works that way.

@default9740 3 жыл бұрын

Use a very narrow flat screwdriver (jewellers driver) to pry the c-clip out. Replacing it is trickier without a special tool from the manufacturer, but not too impossible. Replacing a ball spring takes less than a minute with practice and the special tool.

@AceSolomon94 3 жыл бұрын

I would've tried using a small vice grip & pull up simultaneously with one hand as I use the other arm to secure the tool down while using the other hand to lift the collet up.

@BigHoss-dk4qj 3 жыл бұрын

Why not take the collet apart, snap ring, spring, and detent ball. Then push it out with a pick. Or was it not possible with the broken bit?

@BuildsStuff 3 жыл бұрын

@BigHoss-dk4qj 3 жыл бұрын

@@BuildsStuff my eyes aren’t what they used to be.

@ceeweedsl Жыл бұрын

@@BuildsStuff Turns out your concern was unfounded. Not hard. Putting the split ring back in was a matter of holding down one side where it's split with thumb then pushing down around the ring with a jeweler's screwdriver to snap into place. Easier that I thought it would be as well. Just be prepared for it to fly off once or twice and have a clean floor space around you.

@loneswandon651 2 жыл бұрын

This video looks like a deleted scene from Iron Man

@loneswandon651 2 жыл бұрын

I was talking to the screen and everything.

@damodaraomalley3974 Жыл бұрын

🤣🤣

@joshualatham3778 2 жыл бұрын

Take the bit release off and you can pry the old bit off

@ceeweedsl Жыл бұрын

This is exactly how I would have approached it. Luckily I watched a video where they show to remove the split ring that holds the collar on. Use two picks or a pin and a small screwdriver. Out comes the retaining ring, then a waster then the collet. Be careful at this point there will be two ball bearings that the collet was holding in. These retain the driver. Remove the balls with a magnet before they fall out and then shove a wire inside the holes where they went to push up the bit from it's base. Much easier than all this. But, again, left to my own devices, I would have done the same. "HOW TO Remove Broken Impact Driver Bits - Don't Get Mad! "

@tearodman 3 жыл бұрын

did U see that vcg construction where they repair the ball bearing of this chuck? watch?v=Oo7urn6TYYc

@tearodman 3 жыл бұрын

for the record, I tried to repair a NOS Makita Bdf444z I bought that had a jammed chuck and I did something you did. But I couldn't reassemble well the tool and in the end I sent it to the repair service. Result is I broke some internal parts in the process and it had cost me 1/3 of the tool in a new casing and another small part that broke, lol. In the end I saw a video for replacing the chuck and I din't even needed to open the drill.

@BuildsStuff 3 жыл бұрын

I don't watch that channel.

@smartalex995 Жыл бұрын

Oh shit ahhaha i actually tried some two magnets i have while pulling the black collar on it and it actually worked . Thanks man good idea there 👍 👌 😀 💡.