Thank you very much for your comprehensive video!!! I received my sakura today and I'm going to attempt to assemble it.

I love when you upload a vid about a micro rc planes ;)

That's super cool

Good one. Love your channel.

Good job,Ilike 3d airplane.

I have this model partially build in the basement for about 8 years, its badsically the same as your one. I might pick it up again.

Cool video joy. I love micro 3d aircraft!

Damn that music at at 1:15 is 🔥 I was totally staying to freestyle in my head 😂

First From Indonesia!

I love this video

Thanks for posting...

Çok iyi bir proje eline saglık

its cool how it looks like an f3p slow flyer but it flies fast

First, cool! 😃

初めまして、素晴らしい❗公園で楽しめる飛行機ですね。私も注文しました。

Have you tried those indoor slowfly planes?

You can get foam safe CA glue.

What is the AUW? And also what receiver did you use? Can you send me the instructions manual photo, i want to build one by myself.

Plz make a slope souring wing

Is the Akku in the der too

Hello, I couldn't find the UHU brand POR type of foam glue to reinforce the parts of this airplane, therefore is it okay to use Hot Melt Glue in medium temperature to reinforce the parts of this airplane?

Hello, I received this kit version(without any electronic) of E010 Sakura airplane from AEORC factory so I weight the overall body parts of the package included all items but excluding the instruction manual, the weight was 38g(grammes).I searched every where to buy likes this UHU por type of glue but unfortunately, the oversees air transportation doesn't support to ship the glue items through the air. Hence I measured the weight of just only one stick of glue gun stick, it was 10g(grammes) so I asked from the factory that will it fine to use the Hot melt glue for reinforce the parts of this airplane so they said that if I used the hot melt glue the aircraft overall flying weight will be increased so as the result, it would be hard to fly, hence use a specified glue for foam. I am using very light weight electronic components like 2g servos, a 1106 brushless motor with prop saver and a 5030 propellers and a 8g of weight ESC, with a ELRS micro receiver and this Byme A flight controller ,I just prefer to build this model to fly on 1s(3.7v) and so far the motor unit can trust 165g in weight when supply 2s power, therefore if I prefer to build this airplane in 1s(3.7v) power and with using the hot melt glue for reinforce the parts , will it fly fine without any issue?

if i have flysky i6 remote control and his receiver this plane work???

I wonder if anyone's used lighter weight 1s electronics. A 1203 6200kv has about 70g of thrust on a 5030 prop @3.8v

Hello Joy vas a subir el mismo video al otro canal no

Does it have any type of stabilization in the receiver to get it out of trouble when needed ?

for beginners?

Your troubles with motor loks me like bad timing setup. You can reed manual which was suplied with ESC how to setup higher timing. Very simple procedure just listen beeps and moveng throtle up and down based on count of beeps. I bouth it as well and it works well. I am just little bit disapointed that servos are quite slow. Whole system works on low voltage 4.7v. definetly it will be improvizace to run it on 6v but it means diferent esc may be receiver as well. Or buy better servos. Both ways are dificuilt and expensive for me so i set it up to use just part of servo stroke(70%). I lost resolution and force but gain speed i hope it will be ok. Enjoy flying bye R.

where are you from

It's tailheavy

Where can you buy it ?

where I can buy tht sir

got one in and motor wires were ripped out of motor with no way to solder back on and the carbon was wrong size ..!!!!BUY AT OWN RISK

WAIT? There are 2d rc planes?

Plane is way to small if you have a biger plane around 80cm span you van fly way better and you van hover better

Too bad radios don't come with the plane

i have a real flight rc sim

Nicekzfaq.info/get/bejne/gK54l7Z8srulaWQ.html