No video
MINNKOTA ULTREX SEAL REPAIR AND BEARING REPLACEMENT - STEP BY STEP INSTRUCTIONS
Рет қаралды 4,924
Күн бұрынIn this video I go through he steps to replace the seals and bearing on a Minnkota Ultrex 24V 80lb Mega Di Trolling motor. Each step is detailed and described to help you if you are attempting this on your own or want to know what's involved.
#Minnkota #DIY #Ultrex
@Jack-qv8mh Ай бұрын
Just ripped an ultera open, following your video. In a tournament a dealer tried selling us a brand new shaft and motor. Tired of our no accountability society. Anyways thank you for this video, truly appreciate it.
@BamaBassCatcher99 2 ай бұрын
What bearing puller? Have a link?
@jrob7538 Ай бұрын
Wire wheel on the armature windings, that's kinda brave, isn't it?
@JPDeRoseOutdoors Ай бұрын
Soft wire
@Corkstercam 3 ай бұрын
Can you ask Alex if when removing the seals and paper tube (Step 17), how close was the inner most seal to the copper bearing flange that is pressed into the brush end housing? When He was removing those seals he punched them out. I was able to get the outside one but the one close to that copper bearing flange I was unable to get the punch on the seal without nicking and misshaping the copper bearing flange. Will have to remove it and press in another one. Does the inner most flange seat right up next to the copper bearing flange?
@JPDeRoseOutdoors 3 ай бұрын
Yes, according to Alex the inner seal was right up against it. Sorry for the delayed response!
@Lear356045 4 ай бұрын
Great video!! On step 18 what would be the orientation of the aft and fwd seal?
@JPDeRoseOutdoors 4 ай бұрын
The seals are uni directional. They are perfectly round
@av8r1999 6 ай бұрын
Question: Do you have to change any seals or gaskets on the sonar puck? It would seem like that would also have a gasket of some sort. ?? Bout to do my ultrex. Great video!
@JPDeRoseOutdoors 6 ай бұрын
The kit only came with the front and rear seals plus the threaded bolt gaskets. The bearing was separate and I got it since I was already in there. Didn’t notice anything for the transducer although I’m sure there is one as the wire runs right through the nose
@av8r1999 6 ай бұрын
@@JPDeRoseOutdoorsI think they might come as a sealed unit the more I look at it. God Bless!
@dustinwright4601 6 ай бұрын
Good stuff
@JPDeRoseOutdoors 6 ай бұрын
Appreciate it
@BamaBassCatcher99 Ай бұрын
What size socket did you use to install new bearing?
@JPDeRoseOutdoors Ай бұрын
Just marched it up to the diameter of the bearing. Sorry, don’t recall what size it was
@BillSr. 4 ай бұрын
What is the best grease to use on lower trolling motors inside of them? Seals and bearings?
@JPDeRoseOutdoors 4 ай бұрын
Alex used a White Grease.
@herbcornelius6188 12 күн бұрын
How long did it actually take, start to finish?
@JPDeRoseOutdoors 12 күн бұрын
About an hour and a half
@jimxiong364 5 ай бұрын
My bearing seems to be stuck. Anyway to unstick it?
@JPDeRoseOutdoors 5 ай бұрын
That’s a tough one. Did you try a bearing puller?
Mr. Figure it out
Рет қаралды 20 М.
Кушать Хочу
Рет қаралды 7 МЛН
Minn Kota Tutorials
Рет қаралды 31 М.
Pure Living For Outdoors
Рет қаралды 8 М.
Jay Summet
Рет қаралды 6 М.
Josh Manuel
Рет қаралды 3,3 М.
Codyakfishing
Рет қаралды 150 М.
Minn Kota Tutorials
Рет қаралды 8 М.