Mintion Lasercam Review | Control Laser Engraver over WiFi | Mobile/PC Control

Mintion Lasercam Review | Control Laser Engraver over WiFi | Mobile/PC Control | Timelapses

Рет қаралды 3,589

11 ай бұрын

This is a review of the Lasercam from Mintion. It's a device that will turn your laser into a camera controlled Wifi device. Unplug your laser from your computer and have the flexibility to put your machine anywhere you want.
Affiliate Link:
shareasale.com/r.cfm?b=238439...
SAVE $30 with Promo Code: LASERCAM
#xtool #ortur #creality #atomstack #sculpfun #ikier #longer #mintion

Пікірлер: 19

@jeffreyrood8755 11 ай бұрын

That's an awesome setup that I didn't know existed! Thank you for sharing this.

@BusterBeagle3D 11 ай бұрын

You bet!

@shawnm4718 11 ай бұрын

Thanks for the video on this. I’ve been looking for one. 2 follow up questions. 1 I’m a little confused can you still use lightburn on your laptop to load jobs and run the laser and use the laser cam? 2 can you still use the cam inside the Xtool enclosed with the lid closed? Thanks again

@BusterBeagle3D 11 ай бұрын

Yes you could run the camera connected to a laptop to directly camera control the laser in Lightburn. However you would not have room to have the camera overhead with the enclosure as well. I had it in my enclosure again as more of a "security camera" view rather then the overhead view. It would just stick out too much to close the enclosure.

@meaganbaumgarn369 2 ай бұрын

How do I set this up with extension kit?

@karlaname9902 26 күн бұрын

My camera won't connect to WIFI- my Xtool P2 camera connects to WIFI in the same room, but the Mintion camera won't connect to my Xtool D1 setup. Where can I go for help? Thanks for your video, it gives me hope :)

@tiffannystipe9626 11 ай бұрын

This is awesome, I wonder if it can work with the Devil1 Lobotomy kit for xtool or if it kind of replaces it?

@BusterBeagle3D 11 ай бұрын

I haven't used of the Devil 1 Lobotomy kits so I can't say for sure. I believe that kit adds a few other things like limit switches and such so it's not a direct replacement but it does add some really cool functionality to it.

@tiffannystipe9626 11 ай бұрын

@@BusterBeagle3D Thank you, yes it adds the ability for the program to run the air assist as well.

@Darryl.M 3 ай бұрын

Interesting. I have been looking at running a Falcon 2 with a Raspberry Pi like I do with my 3D printers but can't find anything.

@BusterBeagle3D 3 ай бұрын

It is nice to be able to run some of this stuff remotely.

@titofashionnn 4 ай бұрын

Can I use the beagle V2 for laser, instead of specificaly the beagle laser cam?

@BusterBeagle3D 4 ай бұрын

No. The firmware is different and the are completely different devices. They can't be used interchangeably.

@Chatz13 11 ай бұрын

Where can I get that board with the measurements.?

@BusterBeagle3D 11 ай бұрын

I have grids for many of my different machines. You can find them on my Etsy page. www.etsy.com/shop/BusterBeagle3D

@cont1origins 8 ай бұрын

Is there a way to use this app from that camera, to another camera? like sculpfun?

@BusterBeagle3D 8 ай бұрын

I don't think you can use this app with a different camera , the app is specific to the companies own hardware.

@TheBlackDove 7 ай бұрын

Does this camera work on Mac? OsX?

@BusterBeagle3D 7 ай бұрын

Honestly I’m not sure. I would consult the website for compatibility. I don’t see why not since you are simply accessing an IP address to access it but I can’t say for sure since I’m not using it with a Mac.