MITSUBISHI 4M40 - DIESAL PUMP TIMING MARKS

Рет қаралды 66,342

Bush Mechanic - How To Fix Your Car

4 жыл бұрын

HOW TO SET DIESAL PUMP TIMING MARKS ON MITSUBISHI 4M40 ENGINE

Пікірлер: 29

@UncannySense 4 жыл бұрын

Good to know, my S1 L400 pump is still going well, but it helps to have this sort of information. Hope to see more on the 4m40

@manealaughlin8230 3 жыл бұрын

Thank you, my vehicul is a 2.8Turbo diesel , so i have to put the Notch at the (T) mark 🙏thanks.

@cobra646 2 жыл бұрын

Here is a link to a directory from the Delica Canada forum that includes engine manuals for the 4M40 and 4M41, including procedures for removing and installing fuel pump www.delica.ca/manuals/L-400%20Manuals%20&%20Plans/

@bushmechanic-howtofixyourcar 2 жыл бұрын

Thanks so much 🙏🏽I lost my manuals years ago could never find them again no matter how much I searched on google 🙏🏽

@sameuljones5496 3 жыл бұрын

I want to turbocharge my non turbo 4m40 so should I adjust my pump to T mark once I slap this big turbo on and wind it up to 30psi of boost?

@Allancoderias072 4 жыл бұрын

Timing mark gear and enjection pump 4m40 canter

@jasper232 3 жыл бұрын

What is the brand and model of this injection pump? Thanks

@roshsookraj790 Жыл бұрын

How many degrees before top dead centre must it be set.

@usmaanbhai 3 жыл бұрын

hi , whats the firing order of 4M40 ?

@odenwaldcruise4794 3 жыл бұрын

What is happening when you install the Pump with non Turbo timing mark in a Turbo vehicle ?

@bushmechanic-howtofixyourcar 3 жыл бұрын

It will cause your vehicle to run badly , because it will not be getting correct amounts of fuel for engine with turbo.

@bhenchannel11 2 жыл бұрын

great bro stop by on the channel

@robwhite240z 3 жыл бұрын

So do you set it at that point. then slide it on, or slide it on to that point . As sliding on will move it 1 whole tooth over.

@bushmechanic-howtofixyourcar 3 жыл бұрын

you slide it on to that mark so you offset it and slide on to point

@712Menzies 2 жыл бұрын

That’s a critical piece of info you left out

@jeffn1384 2 жыл бұрын

So is it reinstalled when number 1 piston is at top dead centre?

@bushmechanic-howtofixyourcar 2 жыл бұрын

Yes

@Armageddon-qo4wy Жыл бұрын

Are those factory notches on the gear or did you put those in yourself

@bushmechanic-howtofixyourcar Жыл бұрын

They are factory notches

@samstripy1187 4 жыл бұрын

I was told that when you put it back into the car it moves one notch when you slide it in, is this actually correct?

@siyabongamakhathini 4 жыл бұрын

yes it is correct , this is because when you slide it in and it touches the gears it moves slightly. I prefer to move it half a notch rather than a full notch

@samstripy1187 4 жыл бұрын

@@siyabongamakhathini so does it need to be set one notch back from the T so it is on the T when it goes in? or on the T before it goes in so it moves forward when fitted?

@siyabongamakhathini 4 жыл бұрын

@@samstripy1187 it needs to set half a notch ( move it slightly above T so notch is slighly above T arrow ) before installalation so when fitted it will push the marks to align