MODEL CAR PAINTING TIPS - Making Water-Slide Decals with an Inkjet

Рет қаралды 72,483

2 жыл бұрын

My Amazon Tools List - www.amazon.com/shop/diecastre...
MODEL CAR PAINTING TIPS - Making Water-Slide Decals with an Inkjet. In this video I go over the basics of Printing Waterslide Decals at home with an Inkjet Printer. I show how to measure original and print, and lacquer coat and finally apply the decals onto this vintage Matchbox Van.
(⌐■_■) COOL STUFF FROM AMAZON (⌐■_■)
Yellow Soldering Stand - amzn.to/3vGo0Pp
Automatic Centerpunch Tool - amzn.to/3pnZv5r
Createx Candy Paint Set - amzn.to/3vqIhrP
Createx Candy Primary Set (mix ur own colors) - amzn.to/3HnpgZO
Starbond Glue w/precision tips (Use JIMMY10 for discount) - amzn.to/3sqQkDd
Dynarex Polyethylene Mixing Cups - amzn.to/3vqITxD
FOSHIO Retractable Blade Hobby Knife - amzn.to/3BY2XbU
Fancy Tape for Pinstripes - amzn.to/3C1q8Cr
Amazon Complete Tools List - www.amazon.com/shop/diecastre...
🔔 Subscribe to my Channel & Click The Bell so you Don't Miss an Episode!
Check out XMC Racing - / xmcracing
(⌐■_■) MY SOCIAL MEDIA (⌐■_■)
Patreon............ / diecastresurrection
Facebook......... / diecast-resurrection-1...
Instagram........ diecastresu...
(⌐■_■) SUPPLIES (⌐■_■)
Createx Paints........... spraygunner.com?aff=21
Amazon Tools List.... www.amazon.com/shop/diecastre...
Starbond Glue........... starbond.com/??rfsn=5814075.1...
Discount Code JIMMY10 - Gets you 10% off
⚠️DISCLAIMER: In this video description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.
Music Licencing by Artlist
Song:On-the-way
Artist: ian-post
#DiecastResurrection #Restoration #Hotwheels #Matchbox

Пікірлер: 125

@DiecastResurrection 2 жыл бұрын

Hey its me again, we gotta stop meeting like this. I'm going to try get a car video done for tomorrow.. Have a great day! Later Gator Baiter. 👍🍺🍺

@gman2721 2 жыл бұрын

You should do a whole series of short How to videos like this, basics of setting up an air brush and cleaning, thining/mixing and spraying paints, zinc plating, ect. Would be very informative to the community and could draw in new viewers looking for how to's.

@HansWeberHimself 2 жыл бұрын

“we gotta stop meeting like this” 😜

@bobshotrodgtx3835 2 жыл бұрын

Great vid , you are truly a master of die cast and more! Been following you for a little while now. So glad i found this chnn, thanks for all you do for the hobbie!! Till the next time. Keep em rolling!

@jona2688 2 жыл бұрын

That's exactly how my French sounds!

@vasili1207 2 жыл бұрын

exactly

@stevewilson6390 2 жыл бұрын

Ha !

@kevincaywood3830 Жыл бұрын

😂

@needfoolthings Ай бұрын

He did gibberish, but it was a perfect french accent. Laughed out loud at that.

@nefifarms4715 Жыл бұрын

I had such a poor day until I heard the mirth in his voice at the French impression. Bravo.

@needfoolthings Ай бұрын

This is agreat tutorial, and that's not something that comes off my typey-typey fingers easily. Your sense of humor is brilliantly applied in multiple thin coats.

@philliprhodes2299 2 жыл бұрын

A few tips: Don’t use cheap generic inks. They easily fade. Go for the branded inks that last for decades, and not weeks. In document set up, don’t forget to set the page to 300dpi. 👍

@johni4591 Жыл бұрын

No need for expensive inks. Use a cheap one and use transparent aerosol

@YarDarkwood Жыл бұрын

And CMYK mode.

@stephaniewright4336 2 жыл бұрын

Thank you for all the great info!

@vasili1207 2 жыл бұрын

Thanks mate ... i am going to try this been printing resin models but sometimes decals would be awesome too. loads of uses not just cars , but eye decals etc it certainly help skip the hardest part of them paint jobs

@juanquirarte6061 2 жыл бұрын

Thanks for this tutorial video. You are the best...

@junkjockey 2 жыл бұрын

Thanks for sharing the video.... Great info

@tt-rs1457 2 жыл бұрын

You are speaking that funny......always smiling when looking your videos. Latest and greatest.....never stop doing this.

@bjimbosld 2 жыл бұрын

You do good work. Great information.

@timstoys1 2 жыл бұрын

Great video... very helpful

@tonybecker8491 2 жыл бұрын

Awesome video, thanks

@wildleeunlimited783 Жыл бұрын

the french part had me rollin!!! great video👌

@everettmonroe3416 2 жыл бұрын

Thanks for the video.

@billysmidway7032 2 жыл бұрын

Amazing that nobody mentioned the decal printer of choice from the mid 90’s, the Alps MD system.. but specifically the MD-1000 that used dry ink (thermal) cartridges including white and several metallics. I made hundreds of decal sets for model trains, cars, space ships, toys. I always used the clear decal paper and did most of my design work with Corel Draw! and Photoshop 3.0.5 running on Windows 3.1 on top of DOS. I’d scan photos of real prototypes and then vectorize (trace) the graphics by hand. The rulers, guidelines and ability to lay out the decal sheet precisely made Corel Draw! the most efficient way to do it but it also let me adjust the sizes to fine tune, the duplication could be set so the next one is pasted at a specific interval in any direction, making short work of a large decal sheet. The vector images also scale easily for larger or smaller models too. I could have printed that Gulf set with white underlay and full color on top.. but you could also get tricky and print a metallic silver or gold under the colors too. I’d sometimes swap cartridge ID labels to trick the printer into doing other stuff too. It was fun to experiment and create decals that I couldn’t get anywhere else.

@hotwheelsbrothers687 Жыл бұрын

Can u make me a custom metal maniacs decal sheet for my Side kick model??

@rccrawler70 Жыл бұрын

Excellent work and very well explained.💯👍

@dddiecast1377 2 жыл бұрын

Great information sir

@DiecastMediaNetwork 2 жыл бұрын

I bought a Ghost white toner printer setup to print CMYK+white. It's complicated and often takes two or three tries to work, but the system is about $600 instead of thousands and clear laser decal paper is less than $1/sheet if you buy 50 or more at a pop. Very cool to see your process. Thanks for sharing!

@diecastRR 4 ай бұрын

Inspiring. You achieved a great effect👍. Regards 🙂

@neilcummings9939 2 жыл бұрын

very informative vid

@YenCrew 4 ай бұрын

That French accent was so accurate tho!! 😂 Greay video, thanks for sharing brother!

@idiotluggage 2 жыл бұрын

Thanks for sharing this. I use GIMP for my editing, but I'm sure your techniques will be easily translated to it.

@silenttraveler2710 2 жыл бұрын

Total Awesomeness… How about a Clear Coat Video 😳?

@TheOldPCTech 2 жыл бұрын

Thank you for this video ! I’ve been wondering how you kept the ink from running when you wet the decals before application. Oh, I just wanted to say that your paint jobs are amazing. I’ve never seen anyone take such meticulous effort with their die cast paint.

@peacemeal3196 Жыл бұрын

Cool video

@garyjust.johnson1436 Жыл бұрын

Happy New Year 2023!

@kevinb9327 2 жыл бұрын

👍 I use Modge Podge Gloss to seal decals with good results.

@frankduncan6399 2 жыл бұрын

Great video! I just started looking for this kind of info! You also must be a hockey player. Hence the last comment you made in the video. LOL

@anokesunboxing-figurenundm2113 6 ай бұрын

Thanks for this Video! Realy helply. hey at 3:50 a German trabant ..coool!! Greetings from Germany!

@kevinokane3702 Жыл бұрын

An alternative to the pixel replacement in Photoshop (seen around 8.00) being used to create smooth visual components is to convert to a vector image (drawn shape and fill, not individual pixels at all). That however requires a program such as Adobe Illustrator or Corel Draw. CD is my (relatively) cheap go-to for creating decals for shield designs on wargames miniatures... (yes, weird but effective).

@SewTexas Жыл бұрын

Thank you.

@jimdiesel7249 Жыл бұрын

The French impression made me spit my coffee on my brand new laptop!! I’ll subscribe

@DiecastResurrection Жыл бұрын

Sorry! 🍻

@jimdiesel7249 Жыл бұрын

@@DiecastResurrection dude no apology required!! That made my morning, I’m researching to make waterslide decals for guitar headstock and such, your video was helpful, I’m shopping right now for a printer, there’s so many!!!!! Any recommendations?

@cottydry 4 ай бұрын

Best start to finish tutorial for making decals. Do you have any links or suggestions on learning just the Photoshop Element basics for things like this? (vs. full blown in depth training)

@BlueGillage 2 жыл бұрын

Thats the first time ive ever seen lacquer top coat not make the ink run. T.y. for the air drying tip. ALSO, acrylic top doesnt make the ink run at all. Works perfect. Goes great with a final acrylic top coat or future finish over entire car/model as well.

@KevBotes 2 жыл бұрын

To save time preping the image, you can always download a png of the original logo if you can find one.

@billbowman8747 18 күн бұрын

Hairspray will also work as a fixative so the colours won't beed or run.

@unknown21M Ай бұрын

love the tutorial I learned a lot man, I m having trouble editing as small as 5.5 mm x 2.8 mm for a license plates, i m new to photoshop when I resize image I dont know how to get the pixels right and clear, any tips in how to get a clear image when printing and the actual image,, thanks

@gusser2121 2 жыл бұрын

Und now we have zee professor Austin zpeaking on zee decals... LOL... you should have a series of vids called "Jimmy's Tech Talk" with all your instructional tips and tricks!

@MichaelBennettEFAddict 2 жыл бұрын

well hell yeah

@r.tistry6631 2 жыл бұрын

All typical home printers use transparent ink or toner. If you have an inkjet printer sealing the decals is mandatory because it's a liquid when it prints and will re-liquify when soaked. I use Testor's Decal Bonder from Hobby Lobby in light coats to seal those. It's ultra thin and works with lacquer and enamel clear coats. If you use a Laser printer sealing the decals isn't necessary because toner is a powder that is heat applied and fused to the paper. But once laser decals are applied you should start with light coats of clear as gooping the topcoat on can damage the decals (cracking the toner or even causing the toner to "halo" - usually the yellow).

@jonytube 2 жыл бұрын

Heyo. What if you used the Burn tool to get true blacks? It blasts the exposure to negative amounts and you dont have to be as careful as you are with a brush

@srsdiecast4598 2 жыл бұрын

Awesome tutorial thank you. Do you have a spot you would suggest for purchasing Decals.

@DiecastResurrection 2 жыл бұрын

Have you checked out Slixx?

@forgotn42 2 жыл бұрын

There are a couple of companies that are making white toner for consumer level laser printers. You basically have to trick the printer into doing it by replacing the black toner with white, but it does work. The best part of this method is it takes a couple hundred dollars (depending on if you have a compatible printer already) to do instead of a few thousand.

@vasili1207 2 жыл бұрын

go on bro let me know how i do it ... have two printers yeah ? one with black and one modded?

@Joey06_ Ай бұрын

The french impression 😂

@jannacino5495 Жыл бұрын

Do you put clear coat on the decals after printing or after you stick it to the car?

@swerves4948 Жыл бұрын

You want to use Vectors for the crispiest decals. Download in .SVG format of logos or recreate the logo in a vector program like Illustrator and export as a .SVG. .SVG format can be shrunk to as small or large as you like without compromising quality and detail 👍

@edition_sixscalediecastmod6084 2 жыл бұрын

I use vehicle clear/top coat rattle can to seal the decals. Im not posh enough to own an air brush so I always use car rattle cans.

@vasili1207 2 жыл бұрын

Bro a airbrush costs about £70 About 10 big cans will cost that. Get a airbrush bro and compressor on amazon u love it

@stxc3119 Жыл бұрын

What website did you use to photoshop?

@rromano158 Жыл бұрын

What inkjet printer would you recommend for printing decals?

@jonesing4life126 2 жыл бұрын

What tool are you using in photoshop to pull the writing from the image

@pjamesqm 2 жыл бұрын

Do you have the 442 Police car decals you did ages ago?

@davidpark905 2 жыл бұрын

Your French is impeccable. Haha

@kmcrvtec 8 ай бұрын

What program are you using to do the decals on?

@FeralPatrick 2 жыл бұрын

I use Testors clear matte for my decals and no running so far.

@jacobmckenna8282 Жыл бұрын

You need a special app or program and what kind of printer do you use

@Gappasaurus 2 жыл бұрын

14:25 Ohhh yesh, very toight… toight like a toiger 😄

@muhammedocal8618 Жыл бұрын

Hi What kind of paper should I use to print eyes from inkjet printer for Figures and can you share the link?

@stltrekmodels.4157 Жыл бұрын

so are the expensive machines just laser printers? Along with the more expensive decal sheeting to match? I am making 1/200 scale Romulan Warbird models, and i want really good decals for them.

@safuanaznanchannel4265 2 жыл бұрын

Hi , can normal inkjet printer print decals paper ?

@ivancsneto 2 жыл бұрын

There is a Tool on illustrator called image trace, that's the one to convert images in vector

@felonebike9859 Жыл бұрын

What computer program are you using?

@lesnunley6885 Жыл бұрын

What photo shop did you use

@TheOldPCTech 2 жыл бұрын

Other than buying the more expensive decals or committing to white paint only, there is one way around part of the problem, and that would be to mask off the car and add an area of white paint to the part of the decal that should be white. In the case of the Gulf decals, you’d have to paint a white circle where the center of the logo is. A lot of extra, painstaking work for something so small. I know you could pull it off Austin, but you’re the exception to the KZfaq die cast community from what I’ve seen. An amateur like myself might be able to do it, but would probably have a lot of trial and error involved in the process.

@jerrydwyer9057 2 жыл бұрын

👍

@Shinjuku_24 4 ай бұрын

Which editing software is that??

@i_eat_bus Жыл бұрын

What app u use to design it

@MrTkoryciak 2 жыл бұрын

I gave it a like because of the French.

@Tyboon100 10 ай бұрын

Can you tell me what that function is called your magic wand. I am new mwt photoshop

@reh3ddoes 2 жыл бұрын

"So much French on here you can barely find the English: Papier De Le Que Blubblubblub" LOLOL :D Even the French love #Blubs!

@immortal_cactus4706 2 жыл бұрын

i want to make decals for a lego can this video help?

@MIKI93TheBoss Жыл бұрын

Where i find the file for print decals? Thank you. From Italy.

@ionstriker3721 2 жыл бұрын

Do you need a specific printer to print out the decals or can I use a regular one?

@DiecastResurrection 2 жыл бұрын

I use a inkjet that can print photos Epson xp 15000, you could print on a cheap one too. Higher the resolution the better I would say.

@fortytwo244 Жыл бұрын

You should really be doing this on Adobe illustrator using vector drawings

@adamsukiman1700 Жыл бұрын

Are u using Photoshop to make decals?

@djundaworld 8 ай бұрын

How to make white ink decals?????

@kazama6245 2 жыл бұрын

Are you related to "TheCrafsMan"?? I have a sneaky suspicion you is!😉

@hotwheelsbrothers687 Жыл бұрын

So how do I create Decals for my custom models??? I really wanna do a custom set of meta maniacs decal for a Side kick

@nfsspartanprim 6 ай бұрын

Hes using a scanner to scan each face of the vehicle and using Photoshop to fix the decals on the car. Unless there is a car model, you could use blender and load a texture template.

@cdca1973 2 жыл бұрын

I usually cut my decal paper down to 89mmx127mm, I get 4 pieces from 1 A4 sheet.

@Nookerz 2 жыл бұрын

The OKI Pro8432WT is a white toner printer,, but its hideously expensive new. There are likely others as well.

@clippercrafters5067 2 жыл бұрын

How do you make images more clean and sharp for higher resolution prints ? I printed out vegita and it came out perfect. But then I went to print out other images of him and they all came out blurry. Is it my printer settings? Or is it the lack of clarity or resolution in the original image I selected from google?

@DiecastResurrection 2 жыл бұрын

Alot of times you need to bring the files into Adobe illustrator and then you can scale them down as a vector image. I dont do that often cause it's a pain but works.

@clippercrafters5067 2 жыл бұрын

@@DiecastResurrection is there any other way to do this without doing that ? Or is that the best way to get the best resolution

@SNACKS1414 2 жыл бұрын

Do you have .Ai if you would like I can show you a bit better way to get a little better decals... also I would be happy to send you any thing you need... Love the videos...

@photondebuger45 Жыл бұрын

Maaate I'd love this but i understand nothing of like photo shop or nothin because i is dumb on that, dont you have to buy it first??? Ah doesn't matter but if you use white paper instead of the transparent one is it like a stark white or like less transparent i want to find some to use on a transformer on red paint or color right and the red on red well that make it impossible to see really so a real white background is fantastic

@joseescobedo7899 Жыл бұрын

But then how can you use decals on color not white?

@TakashiAmanoOriginal 2 жыл бұрын

I know that FNSKU anywhere

@garyslentzii2796 2 жыл бұрын

I just google a logo, drag it into photoshop and resize it, then your could typeset the racing in helvdtica italic, I've never had problems finding common logos, graphic artist for over 30+ yrs til they closed.

@fatboyshadetree5139 2 жыл бұрын

Can i use this process to make any decal? I want to make a speed shop logo using my nickname and put it on a few shop vehicles and the side of a building.

@tumama001 2 жыл бұрын

So If you want decals for colored backgrounds you need to buy them?

@DiecastResurrection 2 жыл бұрын

Or get a printer that prints white, they made some older models back in the day that you can still find on ebay. Or you could stencil out the exact size and mask off some white for behind your decal. But it would be tough.

@tumama001 2 жыл бұрын

@@DiecastResurrection Thanks for the reply. Also, If I wanted to print a Gulf decal without white background, would it be better just to buy it If dont own one of those expensive printers?

@Kitzkrieg Ай бұрын

Vern-Yay not vern'errr 😂

@XMCRacing 2 жыл бұрын

Third

@vasili1207 2 жыл бұрын

Reich :P

@greanhare5270 10 ай бұрын

That's a lot of work that could have been done in Inkscape.

@louisvictor3473 2 жыл бұрын

Me, being a sassy bitch, when I have similar projects I literally recreate it in with vector graphics (so the text will be a text field, for as long as I can, either I find the same font, a very similar font that I can easily rater and tweak specific parts, or if it is really bad I just redraw it as a drawing). Assuming I don't find a cleaned up version of them (logos in particular) online, ofc.

@UKGtrotter2k 2 жыл бұрын

Little tip, Look for logos that save as .SVG on Google.

@vasili1207 2 жыл бұрын

little tip svg makes no difference only dpi makes a difference as the printer is the limiting factor 300dpi ... jpg png svg you wouldn't be able to tell if printed between format carriers