Most effective Compact and Simple homemade Sandblaster

Рет қаралды 124,795

2 жыл бұрын

All fittings and valves from plumbing supply, size 1/2. Sandblaster works very good easy and fast rust removing tool. Tank size and hose length can be varios. When using must wear special protective equipment for use with sandblasting cabinet.
▌Want to see more?! So Don't forget to SUBSCRIBE - LIKE - SHARE ▌
♫ Music - True_Messiah
Thank you for watching
► GetWork ◄

Пікірлер: 35

@salvaje9382 Жыл бұрын

So far this is the best I seen that actually works effectively

@Work_G Жыл бұрын

It's nice to hear it

@kwokleunghon3821 Жыл бұрын

Looks great and great idea. Question is where the gas come from?

@Work_G Жыл бұрын

Thanks! Please specify your question I'm not quite sure what do you mean

@Kakunoshin_Niitsu 2 жыл бұрын

How much psi are you using? What is the capacity of your compresor? Thanks, and cool video!!

@Work_G 2 жыл бұрын

Compresor work cycle is 70 - 100 psi, 88L, 21cfm. Check my channel I did little review on my compressor

@julioguerra2023 Жыл бұрын

Desde San Juan Argentina, que compresor usas y con que presión lo trabajas ?

@Work_G Жыл бұрын

Compressor work cycle is 70 - 100 psi, 88L tank. For more info check my channel I did little review on that compressor

@eltanocapo5696 Жыл бұрын

Hola amigo. Que compresor usas. De 50 litros podrá funcionar. Aguardo tu respuesta Saludos

@laurentiu.panait2536 11 ай бұрын

Minimum 200liters

@rosemariemartin3554 11 ай бұрын

nice diy😊 how many CFM and psi of a sandblasting air compressor?

@Work_G 10 ай бұрын

Compressor work cycle is 70 - 100 psi, 88L, 21cfm. It probably would work whit smaller compressor too. I have a review video of that compressor on my channel.

@jasonputtock4428 2 жыл бұрын

who ever needs a lawn mower now.?!

@govindsawant6498 Жыл бұрын

काॅम्प्रेसर कीती एच पी लागेल?

@abin3475 Жыл бұрын

what compresor spec did you use

@Work_G Жыл бұрын

70 - 100 psi, 88L, 21cfm. Check my channel I did short review on my compressor

@mohammedmidlaj4623 Жыл бұрын

The TEE joint, The ELBOW and the TUBE that measures is 1/2 OR 3/4?

@Work_G Жыл бұрын

I believe that is 1/2

@laurentiu.panait2536 10 ай бұрын

I used only 1/2 and works good. You don't need any higher because the compressor is most likely a low cfm one

@mohammedmidlaj4623 10 ай бұрын

@@laurentiu.panait2536 My compressor is 250 liters

@lawrencedavis2089 Жыл бұрын

Interesting 🤔...l would sand ⌛ blast where l could retrieve my sand ⌛ for future use 🤔

@Work_G Жыл бұрын

Yes that is good remark, but then you have to use really good body and face protection because that sand gets everywhere. Of course sandblasting cabinet would be the best option here

@demplik3455 4 ай бұрын

how much sand it comsumes per minute?

@Work_G 3 ай бұрын

Its a difficult question to answer because I never measured that. Can say since the nozzle is quite large, it uses quite a lot

@dereksuperstrong1210 11 ай бұрын

In- complete video

@cetinkeleskeles7989 Жыл бұрын

Why is it so hard to tell the

@robertlyle6277 3 ай бұрын

Used refrigeration tanks are not meant to be reused.

@eghychannel 2 жыл бұрын

Kran uk 1/2 in

@dereksuperstrong1210 11 ай бұрын

You didn't show why you cut the patch on the side why'd you cut the insert

@Work_G 10 ай бұрын

It was some kind of a plug in the tank and it seemed to me that there was a weak point, so I just reinforced it

@outtatime4512 2 жыл бұрын

Too much drama

@gypsymike2355 Жыл бұрын

This is painful …I’m out

@The_OD1 2 жыл бұрын

Bruh this is the same as the one by those Russian dudes. Copied?

@Work_G 2 жыл бұрын

I even don't looked up before making. Just did it from what I had, bought few things and built how seemed proper. BTW all sandblasters is pretty much the same thing

@The_OD1 2 жыл бұрын

@@Work_G yeah all good. Your tutorial is a faster version of theres and easier to understand. Look at his nozzle setup, should fix some issues.