Motion Detection Lights - Easily Install - Cheap DIY Security For Your House

Motion Detection Lights - Easily Install - Cheap DIY Security For Your House - HZ 4132 BK

Рет қаралды 47,380

2 жыл бұрын

If you have a house, you have some exterior lighting AND you have something to protect. To add cheap but highly effective DYI security to your home, change your house lights to motion detection lights. We show you how to easily remove your old light fixture and replace it with a new Heath Zenith motion detection light HZ 4132 BK in just minutes. Quickly change you old outdoor lights for lights that turn on automatically with motion.
Health Zenith motion light are a cheap way to increase your home security and saving electricity. DIY security system for home.
We also explain the basic wiring and how to change any light fixture, inside or outside your home.
We bought this Heath Zenith light fixture on Amazon for just $30 including the motion detection.

Пікірлер: 45

@daywalker407 9 күн бұрын

Thank you Sir for pointing out reaiming the motion sensor

@sammyday3341 Жыл бұрын

Excellent instruction. Thank you very much.

@ryanrogers8211 6 ай бұрын

Thanks for the helpful tips and clear instructions.

@mypointofblue5260 2 ай бұрын

Thanks for sharing. This was very helpful!

@Kimi.labels Жыл бұрын

I just installed mine, thank you so much man

@banjoddwilt Жыл бұрын

Perfect instructions!

@Kiefy6886 Жыл бұрын

Thanks so much! Liked

@PeterSodhi 8 ай бұрын

Thank you

@needles19 Жыл бұрын

Where did you get that square mounting plate so the light stays flush

@allenmarcus6671 Ай бұрын

Is there a way you cannset it to stay on all the time?

@Canongang 2 жыл бұрын

How do I make t stay on. It was blinking then stayed on for a few min then wouldn’t detect me when I walked outside to turn it on

@sheriingrassiaphotos 6 ай бұрын

Our lights are way too sensitive on street traffic is there anyway to lower the sensitivity maybe by placing tape over the sensor

@warrendottin8807 2 жыл бұрын

When the lamp has been installed and placed in test, the lights rapidly flash on and off once motion is detected. Any idea what might cause this, The lights never remain on.

@a2zcarpetcleaningllcwestpa596 Жыл бұрын

Help I have this light but it stay on I’m thinking the sensor is not working

@garywhitesock6239 2 жыл бұрын

I watched your video after installing the same brand/ different model light. I thought I did something wrong, but found out it was the bulb. A sylvania LED TruWave technology wouldn’t work. An older style bulb worked. By the way, we had the same brass lamps. Good video instructions, thanks.

@brianhankins9992 Жыл бұрын

I also had trouble with the bulb...For some reason the manual says to use an incandescent specifically, instead of for example LED or Incandescent. I did get an LED to work, but not the first LED I tried for unknown reasons. So I would say if one LED bulb doesn't work, just try another brand name.

@ReggieC21 4 ай бұрын

Be careful some fixtures work better with the rated bulb for the fixture and proper switch for fixture. For example if you get non LED recess cans and try to put led bulbs in the fixtures and a dimmer switch for them guess what’s not going to work properly?????? The lights.

@yosselisorto3785 2 жыл бұрын

So my landlord installed this but I rather have them on all day because of my light bulb surveillance camera. How do I do that. In the night it works fine but once it’s 8am it sense it’s day light because of the motion detector and has no power lighting the bulb.

@isabelsfoodandtravel4769 3 ай бұрын

Is there anyway to have the light on?

@jingleflagtv8599 Жыл бұрын

My model 4030 doesn't have a manual mode. I'm stuck with flickering over sensitive sensor.

@Thincrust128 3 ай бұрын

What do you do if the switches to change it to test and 5 seconds will not move?

@viswakrmacommunityfoundati9038 Жыл бұрын

How to replace 360 motion sensor?

@garygullikson6349 Жыл бұрын

Can I use the "test" mode to operate lights off and on from interior wall switch and leave motion sensing off?

@brianhankins9992 Жыл бұрын

I would say yes.

@ReggieC21 4 ай бұрын

4:06 don’t worry syrnochrcized light fixtures I’m coming to save you from your comfy junction box 😭😭😕😂😂

@bluediamondlover Жыл бұрын

Love the enthusiasm! I have my lights set to come on dusk to dawn but I’m noticing they’re flickering. I’ve adjusted the sensor, changed the bulbs but still they flicker. They don’t flicker all the time but usually once they come on the flickering starts then slows down.

@URTechDotCa Жыл бұрын

That is odd. Mine are binary - on or off - no flicker. Do you have any old school incadecent bulbs you can try?

@SH-jv5uf Жыл бұрын

Hi Nancy. So are you saying these lights can be set to automatically come on every night and go off at dawn without the motion defection function? Please let me know. That is what I’m looking for.

@bluediamondlover Жыл бұрын

@@URTechDotCa I’ve tried dimmable, not dimmable, incandescent and LED and it still happens. I even took the lamps off the wall to make sure they’re wired correctly but clearly I need a professional because it’s driving me crazy

@bluediamondlover Жыл бұрын

@@SH-jv5uf yes. I purchased them from Lowe’s. They can be set for motion detection and dusk to dawn.

@brianhankins9992 Жыл бұрын

@@bluediamondlover According to the manual (download at Heath-Zenith) a high sensitivity combined with large temperature differences of objects can cause the flickering. If you have an air vent, heater vent or highly reflective surface in the area in front of the light that is probably the issue. Best thing you can do it turn the sensitivity to minimum and possibly turn (to re-aim) the sensor. The manual goes on to day the flickering could be normal operation if heat from other objects is affecting it.

@jeremiahpowell3028 Ай бұрын

I really hate how Amazon doesn’t match prices after the purchase rather then returning and buying again to get the items for cheaper

@TheAstrogrl 2 жыл бұрын

Hi! What is the red wire for??

@URTechDotCa 2 жыл бұрын

The extra wire is connect multiple units together so if the motion is detected from one of the sensors, they all turn on. I do not want that to happen so I did not connect them... but you could.

@DavidGarcia-re9qh 2 жыл бұрын

Good video. You saved some money. I think I can do it myself