You’re welcome.Thank you.

Thank you...

Great.this is not very often leads of motor i did rewind couple motor since i started working here,just want to share if anybody new winder will be seeing those leads something to have an idea how to do it.I was surprised tag was attached on the pulley sounds like funny lol but that was unsafe.Yah i should put that in my safety meeting slip it’s unsafe.be careful bud we don’t wanna lose our finger can’t rewind without it.Take care always.

You’re welcome bro,thank you very much.

Thank You bro😊

Thank You very much my friend,you’re awesome guy.Appreciate it.😊

Thank You Jackly 😊

Thank you.

Cge gawan ko ng content pre para syo.

Thank you 🙏

Thank you 😊

Thanks 😊

@@windertrucker6230 Sir can i get a chance to work with you please sir

@@windertrucker6230 wollcome

Yes i am my friend spare time still put at wirk👍

You're always Welcome Bro.Thank you Keep safe and to Your Family..

@@windertrucker6230 thank you bro👍👍👍😍😍😍

Lots if videos bro but need time to work.

4 poles mate

Parehas lng ang layout ng full slot na coil tapos 2 layer yong iba hinati lng yong wire kasi para ma compact yong winding para kumasya sa slots.ok lng basta antay lng kunti ng sagot kasi baliktad ang oras natin umaga nyo jan gabi namin dito at pag busy sa trabaho 2 weeks na yong huling upload ko d ako mka upload aobrang busy sa work pasensya na

@@windertrucker6230 ok sir salamat sir basta gawin ko na lng sir yung sa concentric na motor yung sabi nyo sir na unahin ko ilagay yung lahat ng phase A then B then C para ndi ako malito sir sa paglalagay ng coil group sa loob ng ng motor stator salamat ng madami sir hangang ngayun pinapanood kopa videos mu sir salamat tlaga ng madami

@@nelsonpantaleon7751 ok lng yan walang problema basta kung may tanong ka comment mo lng.

Thanks,it’s single speed dual voltage 1720 rpm

@@windertrucker6230 9 Leads connection plat stater to motor Digram.

Great..Thank you..Have a nice Day.

@@windertrucker6230 welcome

how many years have you been working in canada.

@@SuhailAnsari0007 almost 7 years

Great bro.

Hi Bro.From Philippines working here in Canada..

Lovely works bro

Hi bro,haven’t seen yet copeland compressor sorry but if have one for rewind it will be uploaded to my channel for sure.thanks

It’s for machine shop motor like lathe machine

@@windertrucker6230 terimakasih banyak master

@@windertrucker6230 super power and speed master,

Single layer lap pasok ng wire phase A sunod phase B then phase C then phase A ulit phase B then phase C sunod sunod yan pag lap sa concentric pwede phase A muna lahat ipasok na coil then sunod Phase B lahat then Phase C.kung bago ka sa rewinding pag napasok muna lahat yong phase A at kung series connection lang i connection mo na bago mo umpisahan yong phase B para dkna malito pagkatapos mo ma rewind ang motor.

@@windertrucker6230 salamat sir 🙏

@@nelsonpantaleon7751 you’re welcome

Both ways pwede kung yong nakaharap sa labas kung gusto mo start lahat pwede at end naman yong lahat nakaharap sa loob.Pero sa akin mostly yong labas ang lagi kung start mas madali para sa akin mag trace ng connection karamihan kasi na original factory connection nakaharap sa labas ang start.

Pag nag trace ka lalo na kung walang numbering or label yong lead wire kung 4 poles gumawa ka ng drawing na 4 na set ng coil tapos i trace mo yong bawat connection ng coil sa drawing para dka malito pag mag connection kana pagkatapos mo mag rewind kasi pag nabaklas mo na yong dating rewind dmo na mababalik yan kaya advice ko lage sa kasama ko gumawa ng diagram ng original connection bago baklasin yong old rewind para d maagka problema pag mag connection na pagkatapos ma rewind.

@@windertrucker6230 ah ganun pala yun. Salamat at napansin mo na naman ang tanong ko sir. At salamat dahil hindi kayo nagtitipid ng isasagot,. 👍

@@prodigy8248 you’re welcome 🙏👍

Sorry noise is always around the shop couldn’t stop them from working.

Salamat Jackly,basic connection lahat magaling jan pati ikaw kayang kaya mo yan👍

@@windertrucker6230 🙂🙏ok sir ingat lage jan.