таки да, . Но меня поражает то, что у них все получаеться. Я сам автослесарь, но такого я не видел. Это варианты станков с ЧПУ, только там процесморы, человеческий мозг. Это просто поразительно

Браво благодаря таких людей они стали космической и ядерной державой !!!

I am American, the idea of driving on that scares the crap out of me. You gentlemen are very optimistic

@@user-tm7kh2de4v надеюсь сварщики корпусов ракет имеют хорошее образование и соблюдают ТБ.

@@Optical_eye Если до этого два года не варил диски, ракеты варить не допустят

XDDDDDDDDDDDDDDD

I dont know, took buddy a while to realize he didn't clamp down the furthest end of the lathe clamp 1:21

when Pakistan roads aint flat, the rims aint round

Its that new alien technology very rare and expensive

How does he endure “arc-eye?” I’ve had corneal abrasions before, and they were *awful.* Arc-eye is said to feel like those.

штанген циркуль ещё

You should wish that wheels never made like this or atleast not such wheels installed over your car !!! Manufacturing standards are close to nothing and same with safety

👍

Are you serious? This is how you did it 100 years ago. No, sorry. We had higher quality standards 100 years ago.

@@gooblio 100 years ago Ford automobile Model T definitely had rally wheels with steel belted radial tires and 100% not 36inch diameter ash hardwood spoke wheels with a metal band that the tire was beadset to with an innertube.

Слелали бы трафарет для удобства

@@user-ew6ei1zn6r Хорошо хоть под гайки сверлят по трафарету :-))))))))

Все современное искусство отсюда пошло

No worries, they are wearing safety-sandals.

@@JohnDoe-es5xh lol....and always the squatting, the dirt floor and the wide flanels...especially in combination with welding and lathe work😬 ..hard working honest people though, just don't know any better and with a boss trying to spend 0 money on his guys...

hahahahahaha

Их наконец то заставили одевать очки и перчатки.

Haha 😂

LMAO

I imagine these wheels will be used on the subcontinent. They might be used on roads that aren't great or used at high speed. So perfect balancing is possibly not that important.

one hit and it is within one thou

the lord of the hammer

Precision wobble, cancels out at 60 exactly

Have seen enough of these vids to desire a smaller version of this kind of hammer.

Это дочерный завод BMW! скорее на bmw x5

Ciezka praca!

Thanks 😊😊

Just interested to know how you are sure that these wheels are truly accurate?

What rubbish those wheels are shit

For slower speeds, these wheels might well *be* “good enough.”

А ты, дядька, ожидал чудес ;) Но они кудесники ;)

I especially love when he let the metal smash into his lathe bit dulling it completely. Gave me chills 🤣

Да, можно ж сделать элементарный шаблон, а не вырубать на глаз дырки. Представляю дисбаланс диска

Всё верно, это газ, проволока, гарелка и её расходники, а тут просто трансформатор и держак, из расходов только электроды.

yup and this is why manufacturing in the western world has gone to shit, to much about safety this and safety that and not enough about actually getting the job done

​@@busrsq insurance cost a lot ... you loos arm..need money yes?

Safety shoes don't bend and conform to the correct radius when you footclamp the wheels.

@@cobre7717 no? strange ..

Wish comments regarding osha would stop showing up. Jeez Louise

Are you serious?

Нельзя, так скилл центровщика утеряется.

for that they are not afraid of sanctions))

Don’t forget the safety squint

Never run a lathe have ya? What you're suggesting works fine for retention pressures needed on a tire spin balancer, but in order to put enough force on it as you describe to keep it from spinning while being turned with a tool would most likely cause deformation of the hole. Material spinning in/on a chuck is a BAD thing... and expensive... Try running some of the equipment some time, you'll get it....

@@shuntawolf tha cone wood center tha wheel on tha lathe. He's banigin around on it with a hammer like some moron and tryin ta eye it. You cain't center something precisely by eyein it.

@@hillbillybeerdranker6678 Apparently you can't spell correctly without an education either as you've so graciously pointed out. You'd be amazed what someone can do with enough skill and talent. Just because you lack the ability to do something doesn't mean others also lack it. You also show your lack of lathe operating ability and how things work. Anything from the dimensions of the center hole to the center hole of the chuck to the ability so secure the part in the chuck while trying to use your "cone" are all parts of this equation. That's to say nothing of how many of us have hundreds of dollars worth of analog and digital indicators and STILL bang on the parts to center them in the chucks. When you're good enough by eye to pick a point on the lathe to watch and you can rotate the part around you learn how and where to hit it to get it most of the time within thousands of where it needs to be. Then it's a matter of what are the tolerances of the part, does it matter if it's just a few thousandths off to begin with as you'll be machining it correctly to the axial center of the machine anyway... Did I type this too fast or use too many big words for y'all to understand all this or????

Все кольцевики, драг рейсеры и дрифтеры в очередь стоят.

Что такое «електромотор»?

@@ogogo4154 електродвигатель))

@@ogogo4154 електродвигун.

а от как раз и не просто, выстучать. Это надо чувствовать силу удара, и т.д. Как художник рисует картину. Так же, как они без динамометрического ключа тянут гайки. Я в молодости это проходил, чувствовал , когда болт начинал тянуться

@@tab2tab24 я даже не мог до этого додуматься..выстучать на токарке..

Наш инженер для начала схлопотал бы палкой по спине. И пошел работать как есть :)

Да ваще атас просто!!!

Yeah im starting to understand the world better and whats coming for us

Таки да..мировые автогиганты нервно курят в углу..

@@ValIlin И не даром. Скоро и мерседес будет пол цеха на корточках собирать.

Там внутри инструкция

haha awesome ? that's some pitiful welding

They can't afford a mig welder

tbm queria saber que País é esse?

That is really painful to watch. I was an engineer in an alloy wheel plant and no machining process took more than 30 seconds. We manufactured a million rims a year.