Glad that this video was able to help you. Thanks for the lovely comment 🙏🏻

Bhai it'll work in every case or on any bike.

Ask your mechanic to take out and clean the slave cylinder carefully and clean the slider pins and make sure they are lubricated well with grease. There's a video on my channel on how to service your brake system you can check that out for further information.

@@ARKARIDER he had done all the above things you mentioned twice . It gets ok but after sometime the problem again arise

Nahi bhai acha yahi rahega ki hamesha new brake oil use kia jaye kuki brake oil Hygroscopic hote hai matlab ye ki wo hava mai se moisture keech lete hai apne andar jisse ki unka boiling temperature kam hojata hai. Isse braking performance kam hosakti hai hard braking mai.

Bhai give me some time I'll make a detailed video.

Bhai ABS mai normal brake se lamba Hose hota hai islye ya to zyada pressure lagana padta hai ya fir ap upar brake lever ko press karke fir push karne ki try karo or agar usse bhi kam na chale to ek bar bike ko start karke band karke fir try karo. Kuki ABS brake system mai pump hota hai

Bhai as per your comment I'm giving you some suggestions try these next time. -Remove the bleeder valve properly take it out and check it for the rust from the inside bleeder valves are highly prone to rust if not taken care of. - Sometimes air get trapped in the hose and it became nasty to take it out so do one thing open your bleeder valve and let it open and fill your brake oil reservoir to the brim and tie the brake lever with cord or zip tie and let it stay like that for over night. The oil will start dripping out from the bleeder valve overnight and check it in the morning and check out if you have pressure or not. If yes then all of the air is removed now and now you can try reverse bleeding. ( Put a cloth on the floor if you're doing this otherwise oil will spill everywhere) - As now you're saying that you have done it by conventional and you think that there's still air inside you can do this too - press your brake lever as hard as you can and tie it with the cord or zip tie as tight as possible and leave it overnight or a day (longer the better). And try to feel your brake response if it's more crispier then be assured that air is removed from your system now. - While reverse bleeding check if your brake lever is fully depressed or disengaged sometimes what happens if your brake lever remains engaged even a little bit the hole which allow the oil to come up will be blocked and you'll not be able to push the oil from bleeder valve These are the remedies which worked for me always try to do this bro and let me know if you get success or not . If not then let me know I'll ask my Guru's too.

@@ARKARIDER Yes bro I will try these. Actually I was doing for rear brakes so. Only one way to keep brakes engaged is to put some heavy weight which I m reluctant to do as of now. But I m thinking the issue might have been this. While filling my syringe with fluid I had lot of air gap above the fluid which might be the reason I was unable to push anything into valve. As this was the 1st time I m doing brake bleeding I didnt realize the issue. I was thinking may be valve has some issue. I realized this after doing conventional way and coming back to room. 1st I will try reverse bleeding this time with syringe filled properly and then if still it doesnt works then will try out the remedies you mentioned.

For rear brake what i used to do is put the bike on center stand then tie a strong rope to lever and press it with hands (or you can ask someone to press it with feet as hard as they can) and while keeping the tension on the lever tie the rope with your center stand tightly. In my Apache there's a small metal part coming out of the center stand which works perfectly.

kzfaq.info/get/bejne/jt6Wh9xpsbPToX0.html Bro watch this video after 1:40 for rear brake i made it long back for the same

@@ARKARIDER Thanks for the tips bro. I tried reverse bleeding again today and it worked like charm. At start today also I wasnt able to force fluid back. So I used Trick that I learnt from another youtuber, I pressed the lever slightly 2 3 times and then it started working. I was then able to force fluid through brake line upto reservoir 😀. Hopefully my brakes will now work better. Or else next mod would be to change brake pads to Sintered ones 😁

Full assembly of bike islye side mai rakha hua hai

Medical shop

Great, I couldn't find a syringe more than 5ml