I know this is a older video but I after watching this I feel confident about installing a new cam and it's going to save me a descent amount of $. So now I can have a new set of rear tires also. For that I thank you Mr. Cuervo and I'll also be purchasing your fan kit very soon Thanks again and Live Fast & Ride Smooth 🤙🏻👍🏻

Thanks for sharing this. After installing my big 3 this and bored TB is my next step.

Great video, just installed mine using this! Thanks!

Amazing video, greatly detailed.

I appreciate the content.

Great vid brother, rite now I have a big 3. Want more power was thinking going with big bore kit, stage 2 cam, and ported throttle body. Any advice on whether that’s a good combo to go with or any other options to go with?

Great videos man. New subscriber here. Learning a lot. Just curious, what would happen if you remove the decompressor, rotating shaft and pin? Harder start? No start at all?

What is the main difference on installing the 06-08 700s? Step wise, I seen the bearing but wondering what I gotta do that’s different!

Thanks for taking the time to do this video, Are there any noticeable gains in installing an aftermarket cam with the stock 10:1 compression piston on these 2015+ bikes?

Thanks...great vids. Ya need a head mount camera 🖒

I would like to see a video specific to troubleshooting slow cranking and how to test and verify the damper assy is good. There is no known info on the web about this very important part of the starting system.

Do I have to get the hot cam chain? I have the Barkers big 3 kit after I get this stage 3 hot cam what else can I get to gain hp? Do you recommend dual springs?

How will this effect reliability and how is it noticeable power on a raptor that already has the big 3, ive heard its not worth it I've also heard its a huge power gain what yall think?

I have an 07 Raptor. What are the different steps you mention in your video?

do you need to install 50m throttle on a raptor 700 when you do a stage 3 camshaft

Cuando el seguro está afuera es para bajar la válvula de escape y desp con las rpm sube

Would the same be done for the big 50/50 cam?

I have a 07 raptor programmer and full exhaust with intake what stage cam should I buy

Do I need to upgrade my valve spring and retainers?

does it damage the engine and what does it do thanks

What cam do you recommend for a 2014 raptor 700 with open lid, pro design intake kit, power commander V, and full hmf exhaust? I’m stuck between stage 1 and stage 2, I’ve heard good/bad about both. Any help would be appreciated!

How do you “seat” the cam upon first start up after installation?

Is doing all this stuff essential if you’re just using the quad to trail ride ? Like I have 2016 and it’s completely stock. Is the big 3 a must and if so will it hurt the engine in any way if you don’t add hot cams or bigger throttle body ? And if you do add just the big 3. Do you absolutely need to keep adding stuff to engine or just properly maintain it and will work just fine ? Have so many questions

I know this is for a raptor and that is what you specialize in but what about 2016 grizzly is there anything available cam wise that you know of or anyone i can direct my question to any advise is mush appreciated

Hey man, fantastic videos, I wished I discovered then earlier. I have a question I am hoping you can help with a concern. I had my quad out earlier and it started making this noise like sprocket noise or chain roller noise and i smelled this really intense burning smell that was real chemically, any ideas

The instructions say to lather the cam in redline assembly lube before essembly. Is this recommended?

I installed it and put new oil and oil filter in and when I started it it started to rattle/ticking sound

Hola osea gira la leva y el seguro gira el descompresor por el seguro está afuera y desp cuando entra actúa el descompresor quedando arriba

hi bud ....is there any tutorial for a 2006 model

I have big 3 what else do I need before cam?

hey man whats up wanted to ask you a question what mods can i do expect yhe big three without hirting the engine i mean everyday bike

can I use an 08 cam in my 16 if I pull the bearing off the end of the 08 cam?

Can you do one on yfz

Hey man. Quick question. I pulled my 700 out of the garage to get the lawn mower out parked it and went to put it back in and it just cranks than backfires and idea?

If you run across any prairie 650 parts let me know and I’ll check out your eBay store brother

I bought these and on the directions it had so many cautions should I be worried it said if cam shaft is installed wrong it will break the engine

Must you rejet after this upgrade ??

I installed a stage 3 hotcam on my raptor and adjusted my valves but they seem to make a louder ticking noise is that normal after installing a stage 3 cam?

Mr cuervo What are is the torque specs for the cam cover bolts?

Is tuning required after cam Install?

What is the difference between 2 and 3 cams?

So question? So I have to lose then valves for me to take out and install the cam. I knoe I have to adjust it for the new cam. Just wasn't sure if I have to take it lose before taking out

Hi do u have a email I could contact you at ....I have a few questions on my raptor 700

Why don't dirt bikes have the decompression mechanism or atleast the ones I've owned??? It's a bitch to start those if you don't get the engine in the right position before you kick it

I know its an old video i already have full exhaust fuel custom intake with box and a power commander do i need anything else to run this cam or i should have no power using this cam

I'm trying like hell to pop out a cam and it just won't budge 🥲