Hey Darren. It looks like V2.06 Lua is for ETHOS SR10+ and TD SR 8-12 receivers. I had both of these receivers exhibit a weird phenomena on a gas plane. Channels 7-10 had a serious jitter in them only when the engine was running. I thought it was ign interference, WRONG. It was the 2 independent Stabilizing Functions thing. It was cured by turning OFF the "Second Independent Stabilizing Functions" using the Lua Script V2.06. Its on page 2 of 2 !!!, which is hard to find to adjust. It is ON by default, not a good idea IMHO. This video showed me how to find page 2, at 13:55, thankfully. I hope this helps others who stumbled on this like me. Thanks

Thank you for holding my hand and helping me learn my new Fr-SKY gear. My last radio was a fm futaba, so this is a pretty big jump! Incredible how far things have come in 20 years.

Couldn’t have done it without your help! Thank you so much for sharing your knowledge!

Thank you always Darren for helping us with these awesome updates. I be lost without them. 👍👏👏👏

good video Darren as usual. Would be good to see a video covering a few of the things I saw in this video-The changes in Ethos suite, how to install new luascripts onto the radio so they show in the touchscreen menu's, perhaps even one showing how to do nifty things like change the name in the centre of the title bar like you did with your one awhile ago and used your own logo-I'm sure it's easy, but it would be cool to have videos showing things like this for people and you are definitely leading the way with Ethos Video's mate. 10/10

Thanks once more Darren. Awesome

I have tried what you explain in the video but with an Archer plus + receiver, not the pro, but it doesn't work for me. The SXR goes back to off all the time. For my receiver would it have to be done differently or does it only work for the pro? Thank you for the video!

It's a little bit clunky to be honest, frsky seem to be releasing product quiker than ethos devs can keep pace with. That said, apart from the missing XT30 connectors which I had really grown to like, and configuration being in the wrong part of the OS, the new archer plus SR10+ is fantastic. Two independent gyros on the same receiver opens up a lot of possibiities. Assuming they release an archer plus 12ch stab rx, i can replace some fairly complicated setups in thrust vectored EDFs with a single rx. Even just having independent yaw stabilised channels means you can effectively use one as a steering gyro, without overcooking rate gain on the rudder. What i'd love to see is independent flight modes for the two stab loops. Frsky are really knocking the hardware out of the park.

ELRS and Crossfire as well I understand. Nice. How about the INAV and YAPPU LUAs?

Hi Darren great video to help us! I have the X20S FCC version and I already used EthosSuite to update my X20s with the latest Firmware ver 1.4.9, FCC already. Do I still need to update my X20s to the latest RF Firmware ISRM -TD Module to ver TD 2.2.4. Are they separate software components. When I go to the info screen, i only see the Firmware Version 1.4.9. But i don't see the Internal Module TD-ISRM version info. Why is that. Thanks.

hello Daren many thanks for your video....I can't find the scripts folder on my X20s radio and so I don't know where to put the LUA files ????

Hi Darren, They released a new LUA tool set for the Archer SR10 plus this week. Can you do a new vid for it please. Many thanks EJ

Hi Darren, will you be doing a vid on how to set up a sensor using an SR8 pro or SR10 pro? To an x20 using ethos? Struggling a little and your videos are so informative. Cheers-Ant

Please redo all your videos with a Radiomaster Tx16 or any modern EdgeTx radio. There is a real need for information related to NON-frsky radios and binding the new AP rxs.

Thank you

slightly off topic but i have a brand new X20S and a TD SR18 and cannot get the SRX working. Updated firmware for both There are no icons on the info page and the SRX under devices somewhat activates but won't accept any settings. The stabilization works but one elevator is backwards and off course I cannot enter any gains. I appreciate your videos, the learning curve with FrSky has been much quicker as a result but i'm stumped on this.

Hi mate, thanks for that vid again….Still have problems with X20S, SR10+ Receivers….Everything is up to date and Lua Scripts also…As soon as I turn stabilisation on, there will be no output on the channels, just on gas…I tried it now with the second SR10+ and both show the same issue…Maybe you can show the combination of SR10+ together with the X20S in one of your next vids…by the way you can turn back to page 1 in Lus by longer pressing the Return button….Best regards and keep up your brilliant work.

Hi, I’m trying to calibrate the TD SR 12 receiver. I can’t seem to get the icons that you get on your radio. The one that appear after the info icon. I downloaded the Lua scripts, but I think I’m putting them in the wrong place???? Please help.

I must congratulate you, on your knowledge of the FRsky system. Were you involved in the development? On the SR8 Stabilized RX, how does the RX recognize the 4 controlling channels? I contacted FRsky, BF finding your channel, and they indicated a different channel for the Gain (Ch13) and the modes (but did not specify a channel for modes) BTW what happened to CH11? Why was it overlooked? Does the RX have to be powered during the TX programming, to recognize the keystrokes as they are entered? It also should not be this hard to program a toy airplane!!! Apparently the word 'Intuitive' does not translate into Chinese???

Pleased these are working.

Hi Mr D Can you please help? I have been attempting to set up Stabilisation. All firmware and scripts are up to date. The receiver is bound and stabilisation channels 13, 14, 16 haves been set. SR10+ Calibration is complete OK Self check carried out, all stick gimbals calibrated Gyrogain adjustment on Channel 13 working OK Flight modes on channel 14 working OK, although I can not see any point with the switch in central position as all it seems to do hold all control surfaces in the central position, the same as when the gimbal sticks are central.(excluding throttle). Here is my problem: I cannot get channel 16 emergency mode to work. I can see the switch is active in the Mixer and also in Outputs, but the control surfaces do not change when tilting the aircraft? Completely dead. I have two SR10+ receivers and neither of them work in emergency mode. I have successfully set up SR8 stabilisation receivers in other aircraft OK. Does anyone out there have a solution to this issue? Thanks a lot Rosco

Hi Darren, thanks for the video. I am a bit confused you about the receiver you are adding the Lua Script to FW up date. You are saying you are updating a Archer 10 plus but you showing a SR10 pro. Do you use the same Lua script for Eather one of those receivers? would the same download be for both of them. I look the download for the SR10 pro Lua Script it said it is for open TX. I have a SR10 pro receiver. Thank you.

Hi dude! Why can I see the lua scripts icons in GENERAL??? I have a X20S, Regards!

I’m curious if this is possible for open TX running edge tx. The receiver is a archer s8

THANKS I see you plug in the USB in the transmiter and you get a 3 choice pop-up window. I don't get that. Did I miss something? I am up to date on everything.

if you wanna setup a camera gimble on CH 7,8 you have to turn off "stabilizing" on page 2 otherwise putting it in autolevel mode will make CH7 do funny things for some reason.

LUA scripts are not showing up on the touch screen. I have no means to execute the script. The file manager does not allow me to run the script...only move or delete the file. My zip file had three folders, and three scripts...hope this is right. X20: fully up to date. RX: SR8 Plus v1.05 (cannot find 1.08). What am I missing?

i am really struggling with LUA's and where they should go and how to activate them, when i download SD card contents there are only 2 folders , where do all the others come from and why aren't they there to begin with? it would suit me if the X20s came with an SD card that had every folder the radio could use preinstalled on it , i've given up trying to get the stabilisation in my SR10pro to work , i followed your other video re calibration etc and when i get to the move the receiever part near the end my servo's just don't react even with the gain turned all the way in either direction. radio gear should be easier to use than the experience i'm having. i have updated the radio using the ethos suite and it's all up to date so that isn't my issue.

Using the new lua scripts dose the gain channel change from channel 9 to the script to channel 13?

And now i can't flash the new 1.0.9 firmware which came out on oct. 20th; just a few days ago. i flashed 1.0.8 just fine but now having problems flashing the new update; keeps saying binding, binding; binding!!! I never had any of these problems with spectrum; i just didn't want to spend 900 - 1300 dollars to gain more channels, this seemed like an alternate choice but i'm not so sure right now; kind of a pain in my back side. What a learning curve it has been, i feel like i've gone to college on electronics!!

When will the video of the maiden flight of the Sonicmodell Baby AR Wing be released?

do you know why in ethos suite FRSK Flasher -> TD Module (X20/ X20S/ X20HD/ X20HD Upkit) -> latest shown version is v2.2.2 2022-08-06 225KB and not v2.2.4

With this new rcvr's is it still possible to enter self check with a switch, ore you must use this lua script?????

Can I download the lua script intended for the sr10 pro receiver with my sr8 pro receiver ?

Hi Darren. Following on from my last comment if i exit the SRX stable menu, when i go back in the options are greyed out. Click open and they light up. Is it supposed to do this?

Hello Sir! hope you are having a super day. I just installed Sr10Plus receiver and I'm not having good time with it. This how I've got mix page setup. AETR-A2-E2-F1-F2 and 13 is for gain and 14 for mode. When I activate the self leveling mode the flap 8 reacts with the elevator and flap 7 reacts with aileron. I've try couple different thing but didn't change anything, any help would be awesome.

Ok Darrin i'm at a loss here, i have done everything that u did i think but my x18 still will not read the temporary Lua scripts; there are no icon buttons to click on beside the info button, it won't read the scripts. I have the archer sr 10plus just like this one and although the sxr is calibrated and it works on mode select on channel 14, master gains on 13, oh crap on 16. all that works, but on level only i cannot change the orientation of the receiver, nor will sxr enable; self check won't work none of that. Lua scripts are on my sd card just like yours. about ready to abandon this frsky nightmare and go back to my NX-8; at least i know what i'm doing there. Love the videos i wouldn't be as far as i am right now without them; plz help.

Hi Darren. Ive downloaded the latest Lua script, so now i have SRX stable, SRX calibration and SRX basic windows when i go into the system settings. With the receiver switched on, i have module listed at the top of the SRX stable menu. I select open and the options on the lost light up. I can select stabilizing on, quick mode on, select wing type, mounting type and inverse ailerons and elevators. I can operate servos by sticks but no stabilisation. Im on transmitter firmware 1.49, internal module firmware 2.2.4 and receiver firmware 1.05. Ive downloaded the LUA script 2.05. Am i missing a setting somewhere?