I am from Sudan and i learning MRI from your videos Thank you Brother 💐💐💐
@davidbrown7932 Жыл бұрын
I wrap the body coil , never would I use 2 coils as my MRI is old , burn , but your new system amazing I would go for it 🙏 tremendous job Bac
@klompmer Жыл бұрын
I use superman positioning, with body 18 and table coils. This mainly beacause we only have avanto with 60 cm gantry opening ( it can be a problem for most pasient to get the forarm close to the isosenter and you will end up with bad images and unnecessarily problems). With short scantimes, this is 9/10 not an issue for the pasient. Ofc if the pasient suffer from shoulder pain, we always try other posistions like head first supine). And as alway, good video! 👍👍
@Nguyen_MRI Жыл бұрын
Thanks. Many ways to the same goal. 👍
@maryann9715 Жыл бұрын
Supine with hands down. Although this isn’t scan performed often in my Trust. But I found it really interesting I could use two ultra flex coils for coverage. But of course challenging when dealing with a bigger BMI. But this was very educational. Thanks Bac!
@MrAbdul20878 Жыл бұрын
Thank you !!!! Very greatly appreciated all your tutorial. Would you mind to go over how to set up a new protocol. Thank you
@abrabr6720 Жыл бұрын
nice video, thank you
@bism_allah Жыл бұрын
بارك الله فيك ان شاء الله 🤍
@RATED_R Жыл бұрын
First to like and comment
@ahmedabdelmoniem812 Жыл бұрын
great
@yosef8101 Жыл бұрын
i would do it like a superman position and i always feel bad for the patient knowing its very uncomfortable. other positions not possible for me since the scanning bore size is to small.
@Nguyen_MRI Жыл бұрын
It’s not a patient friendly exam. :(
@collinsm.2168 Жыл бұрын
I use the neutral position, forearm, elbow, arm by the side in the true anatomical position. I move the patient towards the unaffected side to ensure the part being scanned is close enough to the isocentre. If it's the forearm or elbow that I'm scanning, I use foam pads, immobilisation pads to raise it up a little _ this aids in getting the FOV within Isocentre. In scanning the arm, I don't need this maneuver.
@collinsm.2168 Жыл бұрын
As for the coil, I use the Body coil and I wrap it around the patient's limb for investigation.
@Nguyen_MRI Жыл бұрын
@@collinsm.2168 awesome thanks for sharing your approach. 👍
@collinsm.2168 Жыл бұрын
@@Nguyen_MRI thank you
@franciscomorales15 Жыл бұрын
I do it like as the 1st option but in prone
@claudiotorres913810 ай бұрын
hey man, i had this mri, i need some arm mri to compare, if you could look at it would be so great
@Sudor82 Жыл бұрын
i‘m a bit surprised that a prone positioning is not shown as an option. it’s basically the same positioning as hand/wrist exams
@Nguyen_MRI Жыл бұрын
Yes almost like the first example I had. Could also do that.
@badrlinux6786 Жыл бұрын
super man position or in a side with body coil long side
@mirelamihaila188411 күн бұрын
Ps did you use one or two flex coils as you did for the 3 position?
@fayyazkhan7488 Жыл бұрын
Please sir please send me parameters guide Siemens 1.5 magnetom avanto
@mirelamihaila188411 күн бұрын
For the superman position what did you use the flex coil?
@Nguyen_MRI11 күн бұрын
@@mirelamihaila1884 yes
@mirelamihaila188411 күн бұрын
Did you used 2 flex coils like you did for the 3 position ?
@Nguyen_MRI11 күн бұрын
@@mirelamihaila1884 yes
@Nguyen_MRI11 күн бұрын
Ultraflex 18 ch.
@mirelamihaila188411 күн бұрын
Thank you so much 😊
@paulnoyal Жыл бұрын
👏👏👏
@Aj_For6 Жыл бұрын
How did you label patient orientation for this specific Superman position?
@Nguyen_MRI Жыл бұрын
Prone head first.
@Aj_For6 Жыл бұрын
Thank you 🫡
@Nguyen_MRI Жыл бұрын
How do you perform MRI forearm?
@9cobil299 Жыл бұрын
Like an elbow, superman-pos. with table coils and large flex along the arm.
@selimakko9811 Жыл бұрын
👍🏻
@jidhu2008 Жыл бұрын
Hai bro which siemens software is shown in your video can you just do a video on the software you using in this video which will help for tech who see that for first time Plz replay thankyou
@Nguyen_MRI Жыл бұрын
Xa50 software.
@jidhu2008 Жыл бұрын
@@Nguyen_MRI thanks bro and can you do an outline video the this software if possible
@ehimwenmaj3438 Жыл бұрын
Sir I have a question about mri. A T1 SE scan is made with the following settings: TR 500ms, TE 20ms, matrix 192, FOV 256, NSA(NEX) 5, scan time 8 minutes. The lab technician is dissatisfied with the scan because the time is much too long. He wants to improve this, and negatively affect the other image quality and properties as little as possible. Reason which parameter (FOV, matrix, TR, TE, NSA, slice thickness, flip angle) you would adjust for this and which value you would choose for this. Only one parameter may be modified. Should I change the NSA(NEX)?
@Nguyen_MRI Жыл бұрын
Changing the nex will affect the scantime and snr. There is no such as only changing one parameter to obtain good images. Have you tried to use the sequence from the vendor?
@ehimwenmaj3438 Жыл бұрын
@@Nguyen_MRI It’s just an assignment from school. I know that practically you can't change just one parameter but i don’t understand this
@Nguyen_MRI Жыл бұрын
@@ehimwenmaj3438 ok. In this assignment nex seems a bit high. Maybe lower this but again depends on what coil you have if there is enough snr to lower. I guess it because you have a matrix of only 192 out of fov 256. Which is not a proper resolution. 256/192= 1.3mm voxels size. So many other factors as well which affect each other.
@ehimwenmaj3438 Жыл бұрын
@@Nguyen_MRI thankyou sir🙏🙏🙂
@sirajahmedsaifi8694 Жыл бұрын
Good evening sir i am from India at up in Rampur .i am big fan of you .will u please share your number to me for any query if needed to me the way of learning is effective . Keep going.