Chinese diesel heater fitting new glow plug and testing
Пікірлер: 36
@dorijoe Жыл бұрын
Thanks so much for this video. We were able to fix the diesel heater with the help of your video. Awesome feeling.
@sukamayoutube23232 жыл бұрын
Thanks for getting straight to the point! Doing mine now! Thank uou!
@stevew99573 жыл бұрын
The glow plug does not need to be quite so tight. It's not under much pressure so just needs a gas tight seal and overnight may cause problems when you need to overhaul. Well done by the way 👍
@MrMeltedwellies3 жыл бұрын
Thanks for the info Steve
@chrisneedham58033 жыл бұрын
It looked like defusing a bomb 💣 in reverse. Brilliant that it's back working again 👍 Cheers🍷🍺🇬🇧🩲👍
@MrMeltedwellies3 жыл бұрын
Cheers Chris toasty warm again 🍺👍🍷🔧
@whippetsadventuresandoneman3 жыл бұрын
Thank you for the great video I only just fitted a brand new one did the first prime set ok, 3 minutes in running it it stopped and came up with the glow plug :( so be best to get a new one take it apart and see why the glow plug errors up on a brand new unit :(
@81eagle3 жыл бұрын
Did a new plug fix it? I just set mine up and it gave the E-3 code for faulty ignition. Brand new out of the box.
@ericatkinson9830 Жыл бұрын
Hello Mark, very helpful video. May I ask if when your heater starts up does it make two or three Phut Phut type noise before actually firing up? Mine does and I wonder if that is normal after changing the glow plug and mesh? It works fine but just a bit slow to actually fire up.
@MrMeltedwellies Жыл бұрын
The old one did but not this one Eric
@mazman83432 жыл бұрын
Great job 👍. Where did you get the plug
@mega-hb4re2 жыл бұрын
How often do you replace the plug?
@oldcarnocar3 жыл бұрын
good job
@MrMeltedwellies3 жыл бұрын
Thank you! Cheers!
@chrisprice9121 Жыл бұрын
Hi how can I check my glow plug thanks
@my_carp_life34243 жыл бұрын
Whats the size of the socket you use to take the plug out
@EVS1956 Жыл бұрын
12mm deep 6point slotted on 1 flat
@jimmurphy47032 жыл бұрын
If you have a mains power out as the unit is working the heat will melt the mother board . Always better to have it running off a battery
@tkipta843 жыл бұрын
I just installed my heater the other day. It turned on once with no issues. Then I tried turning it on the 2nd time and I keep getting error 03. I purchased a new glow plug and replaced it and I continue to get the error code. Any recommendations for troubleshooting? I’ve also contacted the seller for assistance. Still waiting on reply.
@MrMeltedwellies3 жыл бұрын
Hi Tomasz make sure the battery is fully charged and you have purged the fuel line and check for any kinks in the fuel line
@rol82y3 жыл бұрын
This is exactly whats happened to me!! Did you resolve your issue! Was it power supply or dodgy glow plug??
@futurebalance61343 жыл бұрын
Hello, can the heater be mounted on either side?
@jimmurphy47032 жыл бұрын
No , only with the glow plug to the top
@bencurry52953 жыл бұрын
What size mm spanner is the glow plug please;)
@MrMeltedwellies3 жыл бұрын
12mm
@Joeilliano Жыл бұрын
How often should be change the glow plug ?
@MrMeltedwellies Жыл бұрын
it will tell you with an error code
@rayranger8249 Жыл бұрын
Hi mate. I've just received a new heater. Straight away im getting E -3 error code. My voltage is set to 12v and im getting 14.2 on the batts charged by solar. I know E-3 Is a glow plug fault. I've not set the controller fully. Am i doing something wrong or is the glow plug fucked? Regards Ray.
@MrMeltedwellies Жыл бұрын
Hi Ray take out the glow plug it might have a small crack in it