how do i set it? wont work for me

Make sure you set the throttle values from - 1 to 1.

You can also hold the (ALT) key to manually set trim on any aircraft :)

Got mine to stop looping by lowering numbers P=.001 I=.000001 D=5 but now it flies upside down :-)

Matt beaudoin haha, i got mine working its probably because of the center of mass and lift that are different on each plane so i just kept changing numbers in the pid untill it worked well, i had it go upside down at some point aswell, so keep changing the numbers in the pid and youll get it working aswell

Tried this and the plane just nosedives - how do I know which one to adjust?

invert it

​@@jacksonpilarski8710 invert it, if it nosedives then make P lower, the higher the P value, the more aggresive it is, the D value helps to smooth it out and stops rocking up and down. Here is a general tip: when changing your altitude dont change it by more than 100, if you do it will likely break. To prevent that i have another system for when it is going at over a 12 degree angle up or down that will use another pid to go to the inverse of what it is doing already and that makes it stay between 12 and -12 degrees. That is using a tilt sensor btw. Also you can have another tilt sensor facing to the side and use a pid for roll, that way it stays perfectly level, really good for when you are yawing because yawing makes you roll slightly. for roll i used P: 5 I: 0 D: 1

My plane Is doing BOING BOING with the elevators and it's really annoying

Try inverting the roll

@@PizzaPowerXYZ you should increase the damping coefficient of your pid, it helps!

@@waggel120 ooh thanks

My plane is doing backflips

Have you tried inverting the output? It worked for me.

same

Same issue, inverting output doesn't help.

Glad I'm not the only one having this issue.

i know it is the same fore me

same

Same. We need a Gyro Scope tutorial from you.

Are your inputs reversed?

invert it, if it nosedives or backflips then make P lower, the higher the P value, the more aggresive it is, the D value helps to smooth it out and stops rocking up and down. Here is a general tip: when changing your altitude dont change it by more than 100, if you do it will likely break. To prevent that i have another system for when it is going at over a 12 degree angle up or down that will use another pid to go to the inverse of what it is doing already and that makes it stay between 12 and -12 degrees. That is using a tilt sensor btw. Also you can have another tilt sensor facing to the side and use a pid for roll, that way it stays perfectly level, really good for when you are yawing because yawing makes you roll slightly. for roll i used P: 5 I: 0 D: 1

@@larsimann3032 dont need a gyro, make your own, its worth it, trust me. You need two tilt sensors and a little bit of logic, or just look in the stormworks workshop for premade ones

a add might not work so well on its own; let's say PID gives -1 and you give +1 ... it gives 0. I'd put a threshold on your stick input; if it's non zero; you can disable the switchbox temporarily; when you release the stick the Autopilot reverts to controlling the plane

its called add some trim to it xD use a function block with x+0.01 or whatever to change it, when flying do alt+w or alt+s to add trim, it tells you the trim value so you put that in.

Try inverting the signal maybe

@@MrNJersey here's a timely reply, the read out says the pid keeps going into the negative no matter what input i give it so idk, guess i'll have to play around more and see what happens.

now it does random things , not even up then down then up then down ... just pure randomness , and it never does the same im fricking lost

fuck it, it dosn't work im out

did you figure out why?`mine does the same

because you have to invert the pitch but only for the pid switchbox connection

@@sgtnseven3415 How would I invert it?

@@en_erik6429 numerical invert logic thing or a function block with x*-1

same, you ever find a fix?

@@ApatheticBeaver I haven’t

Initialy i had 2 medium ( aircraft one's ) and i added 4 more to have speed.

@@secretgaming5739 gearbox? dont make the ratio too extreme or the engines will stall, if you have temperature control on it then make the rps higher

you can raise the rps of the engine in config (this will make the engine run hotter though)

Fail, this has now official not worked on any airplane

@@LukeRen-rl4yv Yea you shouldn't try it cause he doesn't even tell you what to do he just makes you watch him move logic around without telling you

Edit your PID with better values

MrNJersey i did but in what numbers? From 0.1 to 1 or 0.6 or what they must look like on a bomber