As a retired stage rigger, I think it should be emphasized that these ideas are for decorative use and should NEVER be used in a "life safety critical" situation or where something might fall on someone. Drilling a bolt seriously weakens it and welding on it would further weaken its temper and strength. Welds on equipment that must be safe should be xrayed or magna-fluxed to check the bond of the weld, or load tested to at least 5 times the expected loadFor side ways loads, only forged eyebolts should be used with flange bases.

not sure what the cool idea's were but this guy is sure good at drilling a straight hole through a bolt.

I really enjoyed the technique of jamming the rough cut frayed end through the small hole with camera cuts.

Great technique

Absolutely you are right.before this video we don't know about your extraordinary knowledge.keep all in your mind.

Good 👍👍👍👍👍

And absolutely never want to see them again.

I think I know why no one’s seen these ideas before

Thank!

Buenos trucos

Thanks

I'm at 4:19 and I just realised I've probably seen at least 1 idea fully realised, and I couldn't tell you what it was supposed to be

Muy buenisimas ideas,gracias mil.

Super.... Good job 💐👏😂

i need steel cable for something. let me secure it to drywall.

Great ideas . . Thank you very much Sir

Nice idea i like it too much,,i can make with my home,thanks for your idea bro

Когда в мире коронавирус и нечем заняться дома 😁

These strike me as a good solution only if you have $45,000 worth of machining equipment, but not a $0.45 steel cable eyelet.

I came for the bolts... i stayed for the beats.

Excellent congratulations Muito obrigado Thanks

Show us wire rope ideas without the power tool please. Thanks.

This should be labeled, "What me drill holes through bolts."

Harika ...

You're right, I hadn't seen these until now, but I'm certainly keeping them in-mind now! I'll use real crimpers, though...

Loved them. Especially #3 Keep them coming!

Good nice mr suny

Good

THIS IS A BOLT ?? MAKE A SPIN ?? 🤣👍🏻

First two. Pointless. Why not loop through an eyelet if you have crimps then just tight eyelet down. Going away it will tighten and going down the wall it will wrap and tighten. Just drill a hole then put wire through the bolt, tighten bolt. Can even drill it through close to the head and tighten down with a nut. Doesn't even need a hole drilled Pull tight, tighten nut then really tighten by screwing in the bolt. I would place a washer next to the bolt head. Loads of quicker better, easier ways, with none of the tools. nut crimp; it's ok but why not just splice the small easy stuff. If you saw this video you can watch one on splicing. Not sure what the last one even served a purpose for besides looks. This video shows you how to achieve something using more material, more tools, more time, and more effort to achieve one common goal. Good ideas in general just not good ways of doing them

Go to all that effort using mild steel parts that will rust out near in the salt air instead of using 316 stainless steel.

Top!

What brands of drill bits are you using ?

Looks great. Hope it hold high tension. :) thanks

Awasome Brother

Wow so amazing videos

Only if making those length wise holes this easy

Доктор Дью оценил

GENIAL

Amazing creativity. Superb 👍

Good 👍👍👌👌

Nice video! Direct like 👍

Cable specialist are charging us a fortune 👍👍👌

💋❤ Zürich Albisrieden dä rosche 😉🤠

El cable no está bien sujeto ...dé nngun modo confiaria colgar algo

Great video

Mega work

Да не мучайте вы тросик! Заплетите, сделайте красивую, прочную и главное быстро, петлю и цепляйте куда хочется. Нет, если хочется посверлить .... Чужое хочу, я уважаю. Спасибо.

You're wrong. IKEA had a product like this about 8-10 years ago. I have a couple of them in my house.

All of this is easier using ferrules and turnbuckles.

круть!!!

Nice

hey i need a simpler way to connect a cut wire than this on 4:08

Здраааасьте)

Perfect 👍😍👌❤️💯🌹

Last one: just drill the hole smaller in that metal?!?

Некоторые идеи далеко сомнительны...

Zaberdust

Very good 👍

Самоделки ни чем так как это 1трудоемкость,в магазине все эти крепления и растяжки есть

Очень сильно круто 👍

crimping the end of the wire was the weakest part of the process. but as ideas go that was good

dude, you're drilling into a ciment wall with an ordinairy spiral drill (that will be blunt after) in stead of a stone drill, poor example

Nice😀😀😀

👍👍👍👍👍👍👍👍👍👍👍👍

Why so much work? Easier to buy a talrem and a pair of cable clamps. Cheaper and faster.

SUNIFICATION YOUR LIFE MY FRIENDS !! 😆👍🏻

Hi

These are really bad ways to terminate wire rope. None of them would pass any form of industrial inspection, and - as JP says - none of them should be trusted to hold any kind of load. It went wrong when he started to weld threaded rod to a nut, and just became nastier from there.

Ого, сколько дерьмовых идей! Процветания Вашему каналу! 👍

Я так и не понял нах это надо

Käse 🧀

Зачем ты это снимаешь?🤦‍♂️🤣

I had a feeling this was gonna be dumb and sketchy

Poor

these can be useful for clothes lines arthur linden

About the third one...just buy a gripple.

Bikin alat buat bending U aluminium

👍

عينخبش ز

what a bodger.

No

Boludez

The

time waist

👍👍👍👍👍👏👏👏👏❤❤

This is not good idea man

You titel is wrong i have seen them before

😂 Please, don’t waste your time with any of this nonsense!!

😂😂😂👎👎

Bad ideas

01:09 06:25 03:19

Good

Nice