Reloading 12 ga shotgun shells with black powder for cowboy action shooting using common hardware store items. Some of this I learned from Mike Beliveau's youtube channel: / @duelist1954 I highly reccomend checking him out.
Пікірлер: 496
@sleeperno12153 ай бұрын
I watched this video years ago. I have a lot lot more experience loading blackpowder muzzleloaders and making blackpowder buckshot. So, looking at it again with fresh and experienced eyes, this video is very very good for making blackpowder shotgun shells. Very good job sir.
@jamesgenovese73194 жыл бұрын
Notes: 1. If you drill a small hole across that 5/8-3/4" doweling where you want to cut off the hull, stick a #11 XActo blade in the hole at a slight angle and turn the dowel. The plastic will peel off and trim the hulls smooth and square at the same place every time. 2. 3f Goex is too hot for shot. Go with 1f and you will have the square load set up my DuPont in the 1830s. 3. If you use a hard card ( 1/8"-ish thick) over the powder to act like a piston you do better with your load. In some old guns plastic cups will make a mess of things. For sure use at least 3-4 more hard cards on top of one or a fiber wad. 4. Use of fiber wads alone is not why shot donuts. This is caused by acceleration. (Back to #2.) If you slow down your acceleration, shot tends to not donut. ( why your square load of 3f is too hot.) Other than that, this is a very good how to. Good show.
@jaycousland98354 жыл бұрын
Really nice to see someone else is practicing low-tech methods-very satisfying! I'm loading all brass 12 ga BP plinking slugs currently.
@roderickstrong1364 жыл бұрын
Love those reloaded shells. Cheaper than factory loads and accurate. Reloaded for years without using a scale. One day I put too much powder in the shell. THE results were a destroyed firing pin. Never did that again
@Shaker6262 жыл бұрын
Without a scale would be cutting it too close
@silverhairseeker55394 жыл бұрын
Hahahaha, love the comment about the paper punch and shell being matching pink. In the early 80's when CAS (even before SASS) started it was very common to hear all the rugged Cowboys standing around talking fashion and the Cowgirls talking 'bout their new guns. What a sport.
@koolaidblack76972 жыл бұрын
"Not like you'd wanna use black powder in one of those anyway" Funny Tudenom, I'm actually here for exactly that. I was thinking of getting one of those muzzle-loader barrels for my mossberg 500, and realized that if I really wanted the smoke and flame and smell of BP I should just load up normal shells with BP instead of paying another 100 or more dollars on a special barrel.
@gavingaming1234 жыл бұрын
Excellent information and well explained. I’ll be loading like this for my 16 bore. Thanks for sharing. All the best from Scotland. Garry
@jdhenry63004 жыл бұрын
Great video. I have an old single shot that's around a hundred years old with two and a half inch chamber. Been itchin to shoot it , but can't find shorter shells. Thanks to you IL trim regular shells down , and load them with black powder. I know pressures are lower than smokeless , so maybe the ole cannon will roar again. Great video.
@jrcostilla91054 жыл бұрын
You may have heard about the cut down rounds for shotguns they are around a inch and a half long and come in every type of round to. without the wadding powder and shot doesn't take up much room. You can buy them and make them so many people buy them because you can put twice the amount of shells in your tube. Anyone that owns a shotgun should look them up there is even flashbangs. I hope i didn't waste our time and list a bunch of crap you already know about now. Either way good luck
@AnandRaj-iu9rr4 жыл бұрын
This fucken stupid eating lot of time unwantedly.
@juarezderrick96473 жыл бұрын
@@jrcostilla9105 they are called "mini shells"
@waraichs402 жыл бұрын
। ग
@fredford7642 Жыл бұрын
I have loaded many cartridge rounds through the years, shotgun loading is new to me. Looking forward to loading for my scatterguns. Thank you for a good video.
@MrIronlynnx4 жыл бұрын
I enjoyed the ingenuity and commentary. Outstanding! Thanks for the great video. =D
@xzqzq3 жыл бұрын
Very good video. Shows how easy reloading shotgun hulls, especially 12ga. are. I like BP, and have loaded shotgun, rifle, and pistol center-fire rounds, as well as cap & ball & muzzle loaders.... As you stated, if reloading fired hulls for the shotgun they were fired in, should chamber OK... If buying fired hulls, need to size the brass... Lachmiller Shell Saver works well... I use a handheld primer tool, like a nutcracker, although have had only a few primers go off pounding the brass down over the primer.... mainly .38... My supply of BP is 30 yrs old, and I've had to dry it out several times, with an incandescent bulb . Additionally, I like to do binary loads - fancy term for a dribble of smokeless over the primer, to set the BP off properly....Initially, I measured BP as carefully as smokeless...after a while, simply filled the case to the top, crammed a bullet down to compress the BP, and it worked great.... Can use a brass hull base as a primer holder, to use your 12ga as a muzzle-loader. With BP, prompt cleaning is necessary. Don't even wait to get home...with break-action single shot & double shotguns, the barrels should separate from the stock easily....place the barrel muzzle down in soapy water, run the rod & rag up & down, to get the corrosive salts neutralized. A proper cleaning at home would be great.... I enjoy firing BP in modern revolvers.... however, the action tends to get gummed up. Simply take the grips off, drop in a gallon of diesel, work the action after a day or two, repeat. ENJOY !
@mikegreenawalt47262 жыл бұрын
Hi is this george ulicu.. I just read your reply your very knowledgable I have been gun collector and shooter all my life just now wanting to learn about reloading can't wait plus want to learn black powder guns shooting everything
@xzqzq2 жыл бұрын
Thanks. Happy to help.
@sandymilne224 Жыл бұрын
Well done. I have a Damascus style old shotgun and I’m going to start reloading, so this video is informative for me. Thanks
@nesnetram4 жыл бұрын
Great video! I didn't realize it was so easy. Thanks so much for making this video.
@nordberserker15914 жыл бұрын
I purchased a roll crimping tool and hulls/supplies because of this video. I am trying something similar but with Pyrodex and buckshot. Actual black powder is not the easiest thing to find in my area right now for some reason. I probably should try some #9 shot or something, really cool stuff nonetheless. Either way I can't wait to test them!
@mrlongshanks74467 жыл бұрын
Nice video! One thing to take into consideration is to avoid the use of potentially sparking tools such as the (presumably) steel funnel & steel rule. A plastic funnel would be a better alternative, & either a plastic or preferably wooden rule (or thin piece of wood) as a levelling tool would reduce the chances of getting your fingers burned. Very interesting & informative video though, I very much enjoyed it! 😀
@dmithsmith58807 жыл бұрын
Mr Longshanks Everything he is using is Stainless steel or aluminum, both of those metals will not spark, no worries.
@WaiseHail5 жыл бұрын
Better not to go with plastics. Sometimes they can build up a static charge which can ignite powder
@kirkboswell25753 жыл бұрын
Your primer seating dowel should have a small relief hole in the end to allow for primer clearance. Once in a while the base wad gets compressed and without the hole the dowel is striking the tip of the primer. Otherwise, thumbs up 👍.
@sleeperno12153 ай бұрын
Ahh, I had to reread your comment and yes. I use a small hollow pipe so that nothing is resting on the primer. The pipe rests on the area around the primer.
@tedwilliford72183 жыл бұрын
Usually you can find an older Lee Loader kit at a gun show or on the internet for $15 to $20 that has all of the tools needed to reload shotgun shells. A word of caution - if you study a reloading manual you begin to realize that reloading shotgun shells is like baking a cake and you have to use the correct components and the combination (primer, powder, wad, shot and crimp) depends on the type of hull being used based on the manufacturer. Selecting the correct components can be a challenge. Even when loading with black powder the components are important. Also, black powder is different for pistols, rifles, shotguns, and cannons so you need to use the correct granulation (Fg, FFg, FFFg, etc). It will generate high pressures if the wrong granulation is used. If shooting an old twist-steel barrel shotgun it is possible to blow up the barrel because the steel strands making up the barrel may have developed internal rusting that weakens the barrel so it is best to make that one a wall hanger display piece. Additional note, under no circumstances would a load of BB's be wise because without a proper wad and buffering material and shot cup you could banana the end of the barrel. BB's do not compress like lead shot, there is no "give" in the shot column. I am not an expert and provide this input based on my reading of several reloading manuals and study.
@robertfischer3804 жыл бұрын
Instead of a punch I got a 5/8"dowel and put a deck screw into the center, then ground the head off to punch out the caps. It speeds up the process. Don't have to search for the cap with the punch or nail. I put a little tape on the dowel so it just fits. You could use a 3/4" dowel and sand it down to fit as well. Hope this helps someone.
@puddytat542 жыл бұрын
good idea
@jmartin90596 жыл бұрын
*If you splurge for a roll crimp tool and a Ballistic Products shell length cutter... you could make those more consistent and they would appear to be professionally done. Rubbing or isopropyl alcohol will usually remove the ink labels from shotshells.*
@Droodog1273 жыл бұрын
great tip on the alcohol!
@barry94133 жыл бұрын
Excellent period of instruction Sir.
@user-se3sr1kw2a3 ай бұрын
Most funniest part was the pink matching reloading equipment lol 😂😂😂
@stevebrittain3807 Жыл бұрын
"matching pink card cutter" Lol. You have a good sense of humor
@jamescooper26187 жыл бұрын
This is a great video! Thanks for making it for us!
@vijayshankar58674 жыл бұрын
James Cooper to
@krazyinthekootenay7125 ай бұрын
From a Canadian to obviously another Canadian thanks very informative
@paramitadey6606 жыл бұрын
Thank you for your kind reply
@nasiruddinsharif85413 жыл бұрын
folse, vocus, very bad video. time pass, nesty video.
@WildDigger4 жыл бұрын
Awesome video. Getting a old shotgun soon to play with.
@unknowuser18432 жыл бұрын
Thanks, have a 16 gauge Ammo is hard to find in the best of times. Knowing how to reload with simple tools will definitely help mediate that
@francescovito80902 жыл бұрын
Nñnñnnnn
@MrSanteeclaus6 жыл бұрын
You can get roll crimper very inexpensive. it will roll the edge under and hold your top card down. Well worth the coins.
@dougsimpsonmusic3 жыл бұрын
I’m stoked to give this a go immediately!! Great video, pleasant voice!
@MrTudenom3 жыл бұрын
Thanks Doug!
@uarbor70 Жыл бұрын
I was doing this back when I was a teenager although I had the benefit of a loading machine. I used the plastic wods like you and I would cut off a cup but I would also cut off the base and use that part over the powder. It was a lot of fun but I was not getting good groups compare to my regular reloads. You should invest in a roll crimper that way you could eliminate the step with the glue
@blackpowershootercall44507 жыл бұрын
Nice video, i do this the same way, my question is the pink schell you cut off how manny inches is that.
@josephsfields4 жыл бұрын
How about now ?----> 1,112,557 views• You do a really good job on many aspects of the video. You keep it moving with the explanation and demonstration. You follow procedure and add a little bit of technique. I was glad you went into it without a bunch of common sense safety talk about not attempting to do it by candle light, while smoking, or while tending to several small children. New sub here and now i'm going to check out your black powder shotgun video.
@mikebagnallshooting98185 жыл бұрын
Your brilliant dude keep up the awsome work.
@MrTudenom5 жыл бұрын
Thanks an bunch!
@GunsOfTheWest7 жыл бұрын
Nice video! I'm currently working on a video on this very topic. I'm using new shells with unfired primers still in them, but I like your method of repriming the spent shells.
@MrTudenom7 жыл бұрын
Thanks! I can't take credit for the de-priming and priming method though, I learned that from Mike Beliveau's channel (Duelist1954).
@GunsOfTheWest7 жыл бұрын
MrTudenom, that guy's great!
@imtopher614 жыл бұрын
Awesome video. Thank You. I'll be making these for a 12 ga. cannon. ( NO Shot )
@paramitadey6606 жыл бұрын
In your country every thing is available, especially primer If I place an order for primer,will it be possible for me to obtain them by parcel
@MrTudenom6 жыл бұрын
That's true. Most reloading components can be purchased and shipped in Canada as long as you use a courier and not Canada Post for explosive materials. You have to do your homework though and make arrangements ahead of time with the seller and the courier. Some couriers require MSDS sheets to be placed on the package (you'll have to arrange this with the seller), some require someone to sign off on delivery, and most charge extra fees for dangerous materials. Canpar seems to be a favorite for shipping these sorts of things, but you have to make sure they have a depot in your town (most small towns don't). If they can't catch you at home them they will return the shipment to the seller.
@Shootemfulloholes4 жыл бұрын
awesome vid really made things simple!!! now i can reload for my sweet "ELSIE" with damascus barrels but with the correct load ofcourse!!
@hichemakram754 жыл бұрын
احلف وسوطي
@GearTiger0074 жыл бұрын
nice video, very detail and clear,hope see more your video about hunting and gun
@josephnorcalusa17105 жыл бұрын
Helpful information thank you for sharing..
@bunkstagner2987 жыл бұрын
4 c/c volume of FFg. a 1/8" card over powder wad, a 1/2" fiber wad, 4 c/c volume of shot, and over shot wad then give the whole shebang a roll crimp and done. Rifenhauser hulls work better because they are thinner and easier to cut and cheap. you usually only shoot them once because black powder cooks the shell body. How did you turn the roll?
@And-sn7nt4 жыл бұрын
My dad does the exact same thing, great video
@toddcarpenter7143 жыл бұрын
You might want to ditch that plastic dipper for the powder and use something brass. Static electricity and black powder do not mix well! It tends to go BOOM! I’ve loaded tons of black powder, and everything I’ve ever read says stay away from plastic measures! Safety is always your first concern.
@weitzfc16 жыл бұрын
I would advise using an antique shot/powder measure . they measure in dram/ounce .
@bkipad3 жыл бұрын
Very nice, cheap and easy, thanks
@HuntinginLebanon946 жыл бұрын
What are the best types of soft or rough powder fast or slow for cartridge calibre 12 mm for shotgun ?
@MrTudenom6 жыл бұрын
Hi Ibrahim. Shotshells like really fast powders.
@harpdunn15643 жыл бұрын
Can you use a normal shotshell for this like one that used to have smokeless powder
@johnrenken19813 жыл бұрын
Will this work with buck shot or foster slugs as well?
@claytonbartels1306 жыл бұрын
This makes Mr want to reload. That was so simple
@Semyon_Semyonych4 жыл бұрын
Reloading the BP shotgun shells is very simple. As you can see from this video, no special equipment is needed.
@MrTudenom8 жыл бұрын
After that all you need is a second SA revolver and you'll be set for Cowboy Action Shooting 😊
@Mascotal6 жыл бұрын
You want to be careful when tapping in your new primer like that. If the primer goes off, your wooden dowel might become a projectile. Great video though, lots of good stuff here.
@nchummurry72235 жыл бұрын
Is there anyway we can arrange the pellets for better accuracy?? I made one and tried the the pellets spreads too far before reaching the target.
@MrTudenom5 жыл бұрын
Hello Nchum, thanks for the question. I’m not sure pellet stacking is going to help with accuracy with this method of re-loading shot shells. The method I demonstrate is really crude and likely extremely inaccurate. You could try stacking the pellets, but since there’s no cushioning wad the pellets are going from 0 to very fast in an instant, the G forces they go through are likely to deform the pellets and wreck your carefully placed stack. The seal is pretty weak too, so even though the shot is in a cup there’s a chance some of the pellets at the base are being heated and possibly melted together. I’ve never shot the demonstrated load through a crono, but I’m guessing the velocity is inconsistent due to the “by feel” method I use to compress the powder, plus the shell is not crimped. Not only that but there isn’t much variability in burn rate for black powder, at least compared to smokeless, so it’s difficult to fine tune for your particular shotgun. However, you might have better luck if you use a shotgun with more choke, you could also use a more traditional fibre wad and double card wad to seal the load from your powder better. You could also experiment with compression and crimps if you have a re-loading press. The best option would be to abandon black powder all together and seek out information on smokeless loads for your particular shotgun. Message boards are the perfect place to find old gray haired pro’s who have reloaded and shot millions of rounds. They tend to be very eager to help a guy out and can give you all kinds of tips on powder, wad, and shot combinations.
@khalidmahmood60574 жыл бұрын
Very good refilling
@robertrandin95684 жыл бұрын
I have an old double barrel side-by-side Henry 12 gauge shotgun and it for black powder this was very helpful but my question is if you have this shotgun at home for protection and you hardly go to the range and shoot it how long with these shells last in your home or how long can you keep them without shooting and to be dependable.
@MrTudenom4 жыл бұрын
I have some shells that have fired no problems up to 12 months or more after loading, but I live in a relatively dry environment. I suppose moisture would be the biggest threat to reliability since the shells are not well sealed. If you live in a coastal or tropical environment with high humidity then it might be something to worry about. But if they're stored in a dry space then you should be good for years.
@MrUbiquitousTech7 жыл бұрын
Good info; thanks for sharing!
@TheWalkWithAl2 жыл бұрын
Nice video enjoyed it and learn something
@dontcallmetravis2 жыл бұрын
Is the primer different to accommodate burn speed of the powder?
@themischeifguide7 жыл бұрын
The stamp is the best part
@rabahmoha68503 жыл бұрын
Mp M
@nomadsurvival49525 жыл бұрын
could you not use paper and make a tube instead of the plastic wad?
@SilntObsvr Жыл бұрын
A large *pin punch* would be better than your *drift punch.* It's cylindrical, so it won't expand the primer pocket if you hit it a little too hard on the last bump; also, it's got a little bump in the center that will hold the punch aligned with the primer's flash hole. Most likely a 3/16 punch would do the job. Also, after you trim the crimp, your shells are 2 1/2, since the measurement is of the uncrimped hull. Cut off 1/4 inch, and you've converted a 2 3/4 into a 2 1/2 (but that's correct size to feed in a 2 3/4 action when not crimped as your reloads are). For old fashioned non-plastic wads, you'd load an overpowder nitro card, usually 0.125" thick and a snug fit in the shell (or barrel, for a muzzleloader), push that down flat on the powder, then a thickness of fiber cushion wad sufficient to give the column height you want (more critical if you're star crimping than for uncrimped glued-in or roll crimped shells with over shot cards), then shot and either a fold crimp (like most modern factory shells), over shot card plus roll crimp, or a glued-in over shot card like those you make here (which, as you note, don't require any shotgun-specific tools).
@fullstrutn7 жыл бұрын
I load around 70 grains in my plastic shells with a fiber waxed wad for my old NR. Davis and sons double they pattern really well and I hunt with it. Difference being I use a loader and crimp them ,I like the trimmed case look so I went to paper hulls can THESE be reloaded again does the shot itself ''clean'' out the glue
@MrTudenom7 жыл бұрын
I've never reloaded paper shotgun shells myself, but from what I understand they were standard at one time and people reloaded them. I expect the loading procedure is the same, but it would be best to go to a shotgun reloading message board and see if you can get some tips from an old pro. He might save you some grief! The glue is almost always ejected out with the shot but every once and a while I'll have a small amount left on the inside of the shotshell after firing. I soak the fired shells in soapy water after a shoot to stop black powder corrosion, the glue peels off easily after soaking for a few hours. This won't work well with paper hulls obviously, but you should be able to scrape any remaining glue off.
@fullstrutn7 жыл бұрын
I just loaded up a box of paper shells yesterday and trimmed the hulls with an old trimmer worked out great and look good too
@MrTudenom7 жыл бұрын
Nice!
@MrSanteeclaus6 жыл бұрын
Never had a issue with fiber wads shooting a hole thru load
@binandaofficial89093 жыл бұрын
Very nice works
@SUSHILKUMAR-tz3vg3 жыл бұрын
Nicely done
@huxmetalworks73714 жыл бұрын
Great job loved it
@nicerperson17 жыл бұрын
Does this work if you have a lavender-blue shot shell and punch? *_Seriously though, thanks for the video,_* you make it look very easy. Most clay shoots around me are over farmland, they only allow fibre wads to prevent littering. Would a home made cardboard wad / cup work? and have you tried making any?
@MrTudenom7 жыл бұрын
I've never tried myself, but I've seen a video where a guy punches out cardboard wads from a banana box using a 3/4" gasket punch. The box is a bit waxy and is made of heavier than standard material, so I expect it works pretty well. It's probably better to go with a traditional fiber wad, but if your shoot is next week then it might be an option.
@MrTudenom7 жыл бұрын
Oh yeah....lavender blue is perfectly acceptable, as long as it isn't mint green. Mint green is for scallywags, delinquents, and reprobates.
@sunardi94755 жыл бұрын
Gunung kawi
@gopalgopu62804 жыл бұрын
Yoo matching colors of tools is imp to me too .
@buzzclark6 жыл бұрын
Hi. Just subed & liked. I plan on reloading 12 guage shells for my side by side pretty new break barrel. Coach shotgun. My question is this: Could I use BB's? -- Either using the copper or the silver in color BB's?? Also, I'm shooting at an indoor range & could there be any OTHER powder than BLACK powder as this would cause my neighbors on either side to be choked out by all the smoke & air deterioration. I'm hoping this will not harm the barrels of my shotgun or anything else for that matter. GREAT & INSTRUCTIONAL VIDEO. Thank You for your help. Sincerely, JAMES.
@MrTudenom6 жыл бұрын
Hi James (Buzz), thanks for the sub! Most BB pellets I know of are lead with plating on them, so it should be safe to use them. I don't think the plating will do any harm, the shot in enclosed in the wad cup as it travels down the barrel, so it shouldn't come in contact, and even if it did I doubt any modern shotgun barrel would see damage. I'm thinking the plating would be too soft compared to the barrel steel. You could use the methods shown to replace the primer and seal the top of the shot shell, but you would have to look up a suitable smokeless powder/wad/shot recipe from a reloading manual. The volume of powder shown in the video is specific to black powder and would be hugely excessive in a smokeless powder load
@yolo-qr2fq5 жыл бұрын
I would say don't use homemade black powder in a new couch gun as sulfur will mess with your barrel unless you want to clean it after every time you shoot it. Yes you could use BBs as used in BB guns but the range might not like it because you could do more damage then there range can take because they're steel projectiles.
@TheDave5707 жыл бұрын
You might concider using a copper or plastic funnel, due to static electricty!! If that 67 gns flashes you will get burnt !!!!
@MrTudenom7 жыл бұрын
you might have a point! Thanks for the tip Dave.
@dmithsmith58807 жыл бұрын
TheDave570 stainless steel does not spark
@hazoorbux21094 жыл бұрын
Number do
@RabbitusMaximus4 жыл бұрын
plastic is not recommended per the LEE manual for their scoops, measures, or funnels due to static of the plastic and black powder incompatibility. OK for nitrocellulose based though.
@pierreghazarian60873 жыл бұрын
No plastic only very conductive metals.
@HuntinginLebanon946 жыл бұрын
And which best wrap or astrology for cartridge calibre 12 mm ? I prefer astrology
@dlux9233 жыл бұрын
Awesome vid! 👍
@deipweedecuchiekrucher73842 жыл бұрын
Good high quality video, but if you are open to it I have a couple of suggestions. The first suggestion would be to add more safety warnings like reiterating every now and again to make sure the primers are detonated before you try to remove them and reminding people how important it is for weights to be exact and for you to do the proper calculations on powder equivalencies , you know just small things that could have big impacts on people's safety other than that you're doing a great job buddy keep up the good work very interesting stuff here. My grade for this video (which is opinion and for all intent and purpose is 100% meaningless, unless you consider me... some guy you've never met before that you came across on KZfaq to have some merit, well then that's a different story LOL) a solid (B+)
@leodapat913911 ай бұрын
Watching and listening from pinas garita San Enrique iloilo.
@taylorharbin394825 күн бұрын
Good grief. This is so simple even I can do it…and will! Pyrodex is much cheaper than smokeless powder and I’m doing a lot of shotgun hunting these days. Thanks for the video!
@johnwalters74154 жыл бұрын
Can you roll crimp those as well?
@munnazachaudhry53404 жыл бұрын
But from where I'll get the primers
@Columbariusify3 жыл бұрын
Excellent! It's good to be American!
@wajidbmwajidbm13462 жыл бұрын
I want to buy primer, where you get plis help me,
@davidgardner8633 ай бұрын
Using a hammer to seat the primer would make me a bit nervous. If you have a drill press you can use that to press in the primer and compact the powder.
@jamesranger62832 жыл бұрын
Nice. I am debating a purchase of an older double 12 proofed for smokeless. A British hammer gun is my goal but I can settle for a nice Belgian.
@brucepietri84333 жыл бұрын
Where'd the 3/4 punch come from?
@nra17546 ай бұрын
How build the powder black?
@legendhammonds40079 ай бұрын
Have u ever used wax to substitute the glues
@agustingallo4857 жыл бұрын
how much black powder i need for 1oz of lead shot in a 16 gauge (2 1/2 )
@weitzfc17 жыл бұрын
2.5 drams . take 2.5 x 27.3 = 68.25 grains of powder . I would suggest getting a dram/ounce dipper . it makes loading a shotgun shell or even a muzzleloading shotgun easier.
@agustingallo4857 жыл бұрын
thanks dude
@donboehner60057 жыл бұрын
could you do a follow up video with a shot on paper pattern? I think your load would throw an even pattern. I've seen some black powder loads on youtube that would throw donut shaped patterns, at best. Thanks for the vid, nice job.
@MrTudenom7 жыл бұрын
Can do. I should be able to hit the range this weekend and I'll post the results.
@ibrahiminventor64004 жыл бұрын
Like this is a good invention
@AliRaza-oy6pz4 жыл бұрын
What is the black powder is there any another name of this powder ..?
@osok54924 жыл бұрын
Great 👍 You should have a pink scale
@zukoking52916 жыл бұрын
thanks for telling us
@geripin75164 жыл бұрын
Thanks for good infomation
@basantimishra8956 Жыл бұрын
Pleas post a video regarding reloading of rifle & revolvers.
@RACHIDRACHID-mq6kk4 жыл бұрын
Thank you
@v_Shami2 жыл бұрын
wonderful video. something I definitely wanna try, I was planning to also try *producing* my own powder but that seems kinda sketchy as I'm not a chemist so I'll probably just find some
@MrTudenom2 жыл бұрын
That would be an interesting project, though I have seen quite a few videos where they say things like "make in small batches so you don't blow your face off if things go wrong". That scares me a bit, I'd like to keep my face the way it is, I'm rather fond of it seeing that I've had it my whole life. Also, it's illegal to make your own black powder in Canada, so there's that getting in the way as well.
@v_Shami2 жыл бұрын
thankfully I live in the US, and will soon be on a larger property than I am now so i won't draw concern by lighting random powders on fire in the yard. should probably make small batches like you said until I can get something consistent before I even think of loading shells with it
@tobymorgan44317 жыл бұрын
hi. I am new to reloading and don't have any of the kit, is it possible just to buy shells with the same weight of shot you want to put in, take out the shot and replace it with your own shot and then crimp it again
@MrTudenom7 жыл бұрын
Hi Toby. I wouldn't recommend it, but I have heard of people doing this with slugs, and you probably could do it with shot as well as long as the shot weight was the same, but it would be a bit risky. You might also find that the crimp might not work out well depending on the size of the shot you're using. The problem with factory ammo is that you don't know what type of powder they are using, so you can never reference a reloading manual to check your load to make sure it's safe. Black powder is easy since it's so bulky (it's hard to overload) but smokeless is a different story and the chance of a face relocating kaboom is much higher.
@tobymorgan44317 жыл бұрын
MrTudenom if I were to make sure the powder in the cartridges was black powder would that work or is it still dangerous?
@waqarghanisial25043 жыл бұрын
*Does This Time Consuming Exercise Have An Impact On Cartridges Cost ?*
@johndowe70033 жыл бұрын
At 10¢ a shot it's not too bad, plus you can reload shells a lot faster/efficient than he's showing.
@peacefulwarrior40784 жыл бұрын
Have you tried reloading them using rifled slugs yet ? If so what slugs did you use ?
@miamislice32802 жыл бұрын
I use 5/8" steel bearing-balls, usually wrapped in thin cardboard, soaked, and swaged around the ball to smooth it over. Very much less recoil by the lesser weight.
@zenjiethakali58574 жыл бұрын
Can a reused tablet be reused?
@lombaxjcd2 жыл бұрын
Do you need the plastic wad?
@mdjakirhossain8014 жыл бұрын
Hello , have any differences between the real bullet black powder and matchsticks black powder ( use only matchsticks as bullet black powder) ??? Does people may lost his life for the bullet strikes the bullet is made on matchsticks powder ? Please I want to be clear that . reply please.
@MrTudenom4 жыл бұрын
Match heads are not black powder or an alternative to black powder. What you are suggesting is quite dangerous and could give you unpredictable results including damage to your shotgun or yourself or bystanders.
@christopherkharkongor87933 жыл бұрын
Thank you.
@peacefulwarrior40784 жыл бұрын
100 grains of pyrodex and the same EQUIVALENT amount of (I use 6 shot) shot ! Just wondering if the pyrodex 50 grain pellets would work as well ??
@MrTudenom4 жыл бұрын
100 grains? Now that's a load! The pellets are rare up here where I live and I've never used them, so unfortunately I can't give you any good advice. How close are the pellets diameter compared to the bore diameter they are made for? Do they make pellets large enough to fit a bore as big in diameter as a 12 gauge? I'm thinking that would be in the .700 to .750 caliber range minus the thickness of the shell walls.
@oof44334 жыл бұрын
@@MrTudenom now thats what i called a expert ..
@matthewhamrick10994 жыл бұрын
DONT TREAD ON ME !!! Absolutely not. The pellets are usually for 50 caliber. The empty space between the pellet and the case would cause a explosion.
@jacobadair43547 жыл бұрын
Have you ever tried reloading a shell that previously been reloaded in this method? In other terms have you ever reloaded a shell that's has been already reloaded
@MrTudenom7 жыл бұрын
Yup, some of my shells have been reloaded and fired a few times. I have a really hard look at them before reloading them a third time and throw out any that look suspect. I don't bother re using them after the third reloading.