MTB Rear Shock Mounting Hardware Explained | What Is It? How To Measure, Remove and Install

Рет қаралды 90,612

Күн бұрын

Mountain bike rear shock mounting hardware is very simple, yet often causes tons of confusion. So we've gone ahead and created a full comprehensive guide telling you everything you need to know about mounting hardware for your mountain bike's rear shock. In this video, we explain what mounting hardware is, how to find what size hardware you need for your bike, and how to remove and install hardware.
Use the timestamps below to navigate to the section applicable to you.:
0:00 - Intro
0:46 - What Is Mounting Hardware?
4:20 - What Size Mounting Hardware Do I Need?
5:10 - Using The Internet To Find The Correct Hardware Size
7:32 - How To Measure Mounting Hardware
9:07 - How To Remove and Install Mounting Hardware
10:32 - Removing Mounting Hardware
13:37 - Installing Mounting Hardware
15:28 - Special Notes
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
The Lost Co.
Bellingham, WA
360-306-8827
www.thelostco.com
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
#ridelost
#mountainbike
#mtb

Пікірлер: 166

@TheLostCo 3 жыл бұрын

Well, we did it! A 17 minute video for tiny little bushings. If you found this helpful, please like, comment and subscribe. And head over to thelostco,com for any parts you need while you're at it 😎

@josephmcelroy1090 3 жыл бұрын

Where was this video last year when I struggled for about a week to find the right hardware for my 2021 Fuel EX with offset bushings. LOL. great video.

@Wabit01 3 жыл бұрын

Really do enjoy your videos, thank you! One unforeseen issue I came across when upgrading my shock for the first time was aligning the eyelets, where the rear eyelet is 90degrees offset from the frame mounted eyelet. I managed to get it… eventually, but it required a reasonable amount of force to twist the stanchion + small tolerances on the mounting bolts meant it took a fair amount of effort to get right.

@markmckenney4534 2 жыл бұрын

Luv all your content, however the Ohlins info is inaccurate at best.

@coryd7762 3 жыл бұрын

This is one of those videos that won't get you 1 million views but is so clutch for people that need it. You're sacrifice will not be in vain.

@TheLostCo 3 жыл бұрын

We get countless questions on the topic daily, so it was one of those videos that will help almost everyone! Thanks for the kind words.

@ichewtoast111 3 жыл бұрын

The depth of these videos is what we all like to see.

@topgundk 2 жыл бұрын

This video answered ALL the questions i had, when upgrading my shock. Thankyou, this was brilliant.

@nicolaspous7740 2 жыл бұрын

This is the most useful video I have ever seen, thanks! Repleaced the shock by my self after this

@matthewlindberg10 2 жыл бұрын

These videos have been absolutely crucial in replacing my old air shock with a new coil. Thank you guys. Ordered my mounting hardware for you and will definitely recommend your channel to any of my riding buddies needing help!

@nufobiketrip Жыл бұрын

Thanks! this is the most complete and informative video about bushings. It really answered all my questions and i learned new stuff. Cant wait to see part 2 about coil shock. Cheers

@mrkeopele Жыл бұрын

thorough and smooth, didn't include the aluminum pressed in type but with everything you included and the open minded approach it can all be surmised, thank you so much!

@hjanuarius 3 жыл бұрын

Hi Mike, many thanks for the Fox m6 x 21.84 and the bushing removal tool. The mounting hardware are awesome!

@blake175 3 жыл бұрын

as someone who is buying a separate shock, this is one of the most helpful videos regarding the subject I've found!! Thank you!!

@funridemtb8224 3 жыл бұрын

Excellent content, thank you guys !!

@laurynasjagelo5075 3 жыл бұрын

offset bushings usually make custom and frame-specific stuff for your bike. Top notch quality too:) (not sponsored)

@flow3207 2 жыл бұрын

Oh man, I wish I would have discovered this video earlier. It answered all the questions I researched painfully all over the internet for the last two weeks. Great video!

@TheLostCo 2 жыл бұрын

Shoot! Sorry you didn't find it earlier, we will make it more "findable" for people in the future.

@nalder4x4runnerfamilyoverl93 Жыл бұрын

well done Mike. i was actually emailing you about my build and once i hit send i knew i could find a vid on here to solve the question i had about my shock. Mike to the rescue.

@TheArsenalGoonship 3 жыл бұрын

What an amazing video. So good and timely for me as you guys helped me with a rear shock recently!

@TheLostCo 3 жыл бұрын

Glad it helped and we hope you are enjoying the heck out of that new shock!

@jakepaddyfield4767 2 жыл бұрын

As usual, the most complete informative video ! Many thanks !

@chrisfoster3772 2 жыл бұрын

This is the video I needed. Thanks much love

@aidanwhite2333 3 жыл бұрын

Thank you so much for this video, helped so much we need more of these super in depth videos. Keep up the amazing work

@TheLostCo 3 жыл бұрын

Thank you very much! Glad you found all of the info useful!

@bryceb1234 2 жыл бұрын

Thanks, guys! Glad I could buy through you after such an informative video.

@TheLostCo 2 жыл бұрын

Glad we could help and thanks for the support!

@trevorrees1764 2 жыл бұрын

Your videos are absolutely fantastic and informative, and your customer service and technical support are on point. Subscribed and you gained a new customer. Can't wait for my new coil shock to get here.

@TheLostCo 2 жыл бұрын

Thank you so much for the kind words!! Enjoy that shock!

@harryward5618 2 жыл бұрын

THIS WAS IMMENSELY HELPFUL THANK YOU GRAND MASTER

@adrienremillard6206 Жыл бұрын

Thank you for this amazingly helpful video!

@TheCaptainsCog 2 жыл бұрын

Nips out was the info I was looking for!!!

@sportherz 3 жыл бұрын

Great video, I really like watching Mike explain stuff. Now we just have to wait for those shocks to arrive....

@TheLostCo 3 жыл бұрын

We currently have a moderately healthy selection of shocks, but we did just sell through a bunch!

@rightcoastermtb2340 Жыл бұрын

Thanks for the help man! Nips out...got it

@krissv3ctor512 3 жыл бұрын

But you didn’t mention scenario 4: just watching because you’re interested in learning more about bikes.

@nebnollock5198 3 жыл бұрын

Same lol

@TheLostCo 3 жыл бұрын

Perhaps the second most common scenario.

@SudoChuckwalla 3 жыл бұрын

haha same

@Alex-gb4vn 3 жыл бұрын

I was looking for this comment. Same

@leongrund9382 2 жыл бұрын

Amazing Video guys!

@dunin.majewski 3 жыл бұрын

great work, thank you!

@carson54444 2 жыл бұрын

wow it all makes sense now, thank you

@leenpard1480 4 ай бұрын

best video ever seen!! thank you so much!

@tw227 Ай бұрын

thank you for you shock mounting hardware database :)

@thomasoverend4906 2 жыл бұрын

Very helpful, thank you!

@chrisbaldwin5334 2 жыл бұрын

What a brilliant video, so useful and informative

@topspot4834 9 ай бұрын

Phenomenal tutorial!

@phabletfortyfour3457 2 жыл бұрын

This really helped me, just awesome thank you 👍

@Tittiboi_ 2 жыл бұрын

You answered my question perfectly 🤙🏻🤙🏻

@xXwiggieXx 3 ай бұрын

I was desperate to find the right hardware for my shock. With this video it's easy now. Thanks!

@TheLostCo 3 ай бұрын

Heck yeah, that's exactly what we were hoping to help with! -Mike

@americduh 3 жыл бұрын

I got my fox hardware from you guys. Thank you! 😁

@jamesdomenico2953 2 ай бұрын

You guys are life savers.

@johnoliver3106 3 жыл бұрын

Nice viedo. Keep up the good work.

@creativesummitstudios Жыл бұрын

Super helpful video. Turned a semi-daunting task into a quick 15 minute job WITHOUT “official” tools. Thanks guys🤙🏼🤙🏼

@TheLostCo Жыл бұрын

Our pleasure! That's exactly what we aimed to do with this video 🙂 -Mike

@gekkardboy Жыл бұрын

Very helpful as I perform my first shock swap.

@e.aenterprises105 Жыл бұрын

Superb. Thank you very much.

@davidmain8696 2 жыл бұрын

This would have saved me hours if I'd watched this a last week. Thanks for your good work.

@TheLostCo 2 жыл бұрын

You're very welcome!

@12kman75 2 жыл бұрын

great stuff!

@phonymontana4254 Жыл бұрын

Such an informative video thank you so much

@TheLostCo Жыл бұрын

Heck yea Phony! Glad we could help! -Tor

@flyingnorseman 5 ай бұрын

Yall save my a$$ by having correct mounting stuff in stock and item description that made finding it much easier. Shipped it fast too.

@TheLostCo 4 ай бұрын

Woohoo! Thanks for your order and the kind words! Happy trails 🤘 -Mike

@kennanroewer5142 2 жыл бұрын

So helpful thanks

@gingerb36 3 жыл бұрын

Great video

@yumcaxion9993 3 жыл бұрын

All the information here is great but thank you for including the section at the end about 22mm width hardware often being sold as 21.84mm or 22.2mm and which should be used for a bike that specifies 22mm exactly. I found this video while looking for precisely that information!

@TheLostCo 3 жыл бұрын

Brilliant! Glad we could help.

@funky-phantom 3 ай бұрын

Super useful! Thank you. Had to replace my float dps today.

@TheLostCo 3 ай бұрын

Glad we could help! Mounting hardware is quite confusing at first glance, but in the end it's very simple. Happy trails! -Mike

@funky-phantom 3 ай бұрын

@@TheLostCoIt was honestly stupidly easy. I just had to remove the bushings on the bottom eyelet that came in the shock which popped right out, I thought I'd need to order some hardware to remove them at first. Good luck out on the trails!

@allenjanes5976 3 жыл бұрын

Nice job. You have gotten way better. Welcome to the pro's

@TheLostCo 3 жыл бұрын

That is awfully kind of you to say - thanks!!

@AI-Driven-Entrepreneur 3 жыл бұрын

Haha, thanks for this video... china was able to send me a new TR rocker for my Bomber CR I had customized by you guys.

@jeffdana9402 Жыл бұрын

Amazing. My brain has now been enlarged thanks to Lost Co !!!

@jordan_ochoa 3 жыл бұрын

Brilliant, literally 2 weeks late though. This would have made my life easier.

@snarp408 Жыл бұрын

Great video! I just wish y'all had a link to the List Co database you mentioned... Having a hard time finding it actually, thank you so much though this is very helpful!

@leonparadiz3866 2 жыл бұрын

You are the best 🤟

@drwolcott Жыл бұрын

fantastic

@bterper1142 2 ай бұрын

Thank you

@jailbreakoverlander 3 жыл бұрын

perefect F&^%ing timing just order a fox dhx2 coilover for my trek rail 9.9

@talesfromthetrailz 10 ай бұрын

Just open a new tab hahahahaha bro this guy is so funny man. Good info tho thanks Mike!

@evo5349 3 жыл бұрын

I stopped using normal bush and now use needle roller bearings, so much better all stainless and work so much better I have to increase the low speed compression as the shock is free to move better.

@themountainfern Жыл бұрын

This is why I Love KZfaq

@drunken_moose 3 жыл бұрын

Thanks for the explainer. If M8x22 is such a common side how come no one makes it? My Bronson uses that size.

@grundegrimstad4703 2 жыл бұрын

Geat video. Couple of questions tho... 1: Where can I buy the apprpropriate extraction tools (hopefully for less than 120 bucks). 2: How do I know which extraction tool wil fitt my hardware, and 3: Don´t you want to put some kind of lubrication in there? Surely, a bit of grease won´t hurt hem o-rings. - But great video. Keep´em coming.

@EpicSwedishFika 2 жыл бұрын

Very nice video! Thank you for posting! But I have had enough of Fox. Cannot understand why you should pay that much for something more complicated when you can have the same performance from Rockshox.

@seanmcghee4530 2 жыл бұрын

Which way do you orient the metal bushing seam inside the eyelet? I have an older fox float RP23 rear shock

@fredEVOIX 2 жыл бұрын

thank you very much FOX doesn't provide guides or pictures for the crush-washer, upgrading from an older Rockshox system I didn't know where I was supposed to place it and in which direction

@TheLostCo 2 жыл бұрын

Wooooo! Stoked we could help out!

@darylslaughter 8 ай бұрын

Question: Should the frame bolt that goes into the shock eyelet be greased? In other words should the area between the frame bolt and sleeve (aka pin) have grease on it?

@adrian_veidt 2 жыл бұрын

I use an oldschool astrix stryke. I'm trying to put a budget dnm coil fork. I don't know which hardware to use.

@lewisatkinson7277 3 жыл бұрын

Whoop! Welcome back guys! It's been way too long 🤘

@TheLostCo 3 жыл бұрын

It's been a busy busy spring, but we are glad to be back and hope to keep 'em rolling.

@lamonsato6932 2 жыл бұрын

how do you remove/install the bearing for the bearing mount shock?

@MarcWdives 3 жыл бұрын

Option 4, just something to watch

@mrgodzio1750 8 ай бұрын

Hi I measured my frame and there is 66mm of space but I can only buy 54mm or 68mm spacer, so should I buy bigger or should I buy smaller and then use somekind of screw washer to fit it in place?

@jnygaarddk 2 жыл бұрын

The IGIS is self-lubrication, but are the bronze (you called them steel) ones that too? In other words, this none of this be greased on install????

@__marshie 3 жыл бұрын

Should you grease before installation or is dry ok? Awesome vid.

@TheLostCo 3 жыл бұрын

Dry is in fact encouraged!

@jakecampbell8054 2 жыл бұрын

hello, my rear shocks bushings are worn out so do i have to buy all the mounting hardware or just the new bushing??? also how do i know my bikes bushing size??? (marin alpine trail 7 2022). thanks

@vasiliyignatyev6555 2 жыл бұрын

i got a 2010 specialized Demo 8 been having problems finding mounting hardware for my fox dps the frame bolt is 15mm and the eyelet is 15.08, the inside of the frame is 36mm and that bearing the holds the bolt is 15mm , so how do i find a mounting kit to fit if they only come in m6/m8-m10 guess my question is does those plastic bushings have a 15mm diameter

@timlampron2792 Жыл бұрын

Thank you for the video. Is the bushing removal tool specific to shock brands? I have a dpx2. Is there a specific one I should purchase or would any work? Thanks.

@TheLostCo Жыл бұрын

Hey Tim! Taking the bushings out of any shocks should be exactly the same! Your DPX2 should be smooth sailing 😎 -Tor

@tuwaakotv 5 ай бұрын

Great, very helpful... is the shock of specialized enduro which is 205x60 trunnion can be fitted also with nukeproof giga which is the same size 205x60 trunnion. Many thanks

@TheLostCo 4 ай бұрын

Yes, as long as the eye-to-eye and stroke length is the same, then you can install it the other bike. Since you said one bike uses 205x60 and the other also uses 205x60, then that is the same size and you can therefore swap shocks. You will need to swap mounting hardware as those sizes are likely differenet, and you will likely need to run totally different settings on the same shock between the two bikes as the internal tunes are likely a little different. -Mike

@tuwaakotv 4 ай бұрын

Many thanks 😊

@velocity4349 11 ай бұрын

I went to my local bike shop to install my new fox float x rear shock on my Vitus Sommet 2018. They said they can’t install it and told me I need to reach out to the manufacturer (which they also don’t know) to ask what size is my frame mount hardware. I told the bike shop if they can measure it using caliper, but they said they can’t do it like that since my bike is very specific and that I need to ask straight to the manufacturer.

@Axr24have 2 жыл бұрын

Hi guys. Great vid. I am looking to swap out a rock shox monarch (debonair) rear shock for a fox float factory x2 - I’m having issues with the rock shox unit. So your vid is timely. Question; the eyelets on the fox shock are oriented 90deg from the rock shox unit, can the fox unit be changed to fit my bike frame (2017 kona process)?

@TheLostCo 2 жыл бұрын

Hi John! If I understand your question correctly, you just need to make your eyelets perpendicular to one another - this is quite easy! If you take a screwdriver (or something similar) to gain some mechanical advantage and place that into the rear eyelet. Then holding the shock body in your other hand, simply rotate the eyelets are perpendicular. Hope that helps! If you are confused or unsure of anything, give us a call, shoot us an email, or you can live chat us on our website. (360) 306-8827 // sales@thelostco.com

@Axr24have 2 жыл бұрын

@@TheLostCo thanks!

@jubalvw3302 3 жыл бұрын

Do YOU have a Trek Fuel, Remedy, or Slash? Are you swapping shocks and need the correct offset fox hardware? Then you will need; 1. Trek Part number 540755 x2 (the bolts) [warning, do NOT get the trek "lower" bolt 540756 as it will be too short, as others have found out]. 2. 60mm wide upper bolt with 10mm bolt diameter, Fox Part number 803-03-321. 3. 50mm wide lower bolt with 10mm bolt shaft diameter and the correct offset spacers, Fox Part number 803-03-338. 👍

@TheLostCo 3 жыл бұрын

Nice.

@corindimtber1385 3 жыл бұрын

this may be a silly question but is it possible to change from trunion to eyelet??? I have a awesome Cane Creek shock as a spare and want to use it on my 2020 Scott Genius that has a TR shock.

@TheLostCo 3 жыл бұрын

Technically, yes... But it would involve a lot of parts and labor to do so. In the end, it would be more time and money efficient to simply sell it and purchase a new one.

@545future6 3 жыл бұрын

4:20 = funny :)

@omarsolima826 Жыл бұрын

where do i get the metal bushing removal pin and kit? and what is it called and it's diameter?

@TheLostCo Жыл бұрын

Hey Omar! We sell 2 types on our website: thelostco.com/products/underwood-design-shock-bushing-install-removal-tool thelostco.com/products/wheels-manufacturing-shock-pivot-bushing-removal-tool

@jailbreakoverlander 3 жыл бұрын

Lost Co. helped me with harware next day FED X losing my order. Stand up Company to deal with. JMO

@Pieterpittigeportiepeperpathe 2 ай бұрын

So you can use any brand of mounting hardware for any brand of shock, besides the exceptions. The video is about the size of the hardware, but what would like to know: Are the spacers the same size? Or, is the width of eyelets the same across brands? I need a 30x8 bushing for a Super Deluxe, but can't find any from RockShox.

@TheLostCo 2 ай бұрын

Hey there! Please check through the video again as we cover this exact topic at 2:28 -Mike

@TheLostCo 2 ай бұрын

We also have RockShox mounting hardware in stock in m8x30 in stock and ready to ship! thelostco.com/products/rockshox-rear-mounting-hardware?variant=42732113232070 -Mike

@Pieterpittigeportiepeperpathe 2 ай бұрын

Thanks for your reaction. I interpreted it as just the diameter. You mean the width of the eyelet is standard as well? I live in Europe and I only look for bikeparts in Europe. Importing stuff makes stuff expensive. 🙂

@Kactusdog Жыл бұрын

Installed this set on a 2019 Deluxe RT, it was all the correct spec but a super snug fit. I could not slide my tube in the way you did in the video. I had to use a mallet. How critical is it to center everything? I am >mm off.

@TheLostCo Жыл бұрын

Hey there! Sorry, but I'm having a tough time understanding your situation 100%. Please email us at sales@thelostco.com and we'll be happy to help! -Mike

@Kactusdog Жыл бұрын

@@TheLostCo The long black aluminum tube. The one that fits inside all of the bushing pieces! Mine had to be beat in with a mallet.

@markmckenney4534 2 жыл бұрын

Great video, however the Ohlins information is simply not true, need to rectify that. Love your content and you Bruuh!

@ZippyMedia 5 ай бұрын

Hello, my Santa Cruz v3 specifies m8x22 but the only fox mounting hardware I can see is 21.84 or 22.2 Any ideas?

@TheLostCo 5 ай бұрын

Howdy! As mentioned towards the end of the video, bikes that call for 22mm width mounting hardware will always use a 21.8mm hardware when that is the only option since the frame tolerances are enough to slightly squeeze down to the 21.8mm size. The frame will have a much hardware time expanding outward to the larger 22.2mm size, and most of the time just won't even work.

@ZippyMedia 5 ай бұрын

@@TheLostCo Thanks for getting back to me, that makes sense. I can build bikes from the ground up but the shocks were always fitted so I never had to deal with it before. I’ll subscribe to this channel. Thanks again!

@fergushamilton9642 Жыл бұрын

Socket works mint for removal 😅

@augustoutside5130 2 жыл бұрын

Holy shit balls! You just saved me wasting 320$ on a shock upgrade!

@nickjacobson1032 3 жыл бұрын

If only the m8x25 hardware I need was in stock

@TheLostCo 3 жыл бұрын

I wish we had that too! If you sign up for the stock notification for that m8x25 hardware then you'll get an email as soon as we have more 😀👍

@Hudlbuar 3 жыл бұрын

What does „upgrading“ from air to coil even mean? I just did it the other way round ;-)

@TheLostCo 3 жыл бұрын

We mean to convey a list in that section: "Doing an upgrade, going from air to coil, or because your shock is damaged.." as opposed to "Upgrading from air to coil." Hope that clears it up!

@Hudlbuar 3 жыл бұрын

@@TheLostCo No worries, wasn‘t meant that seriously ;-)

@TheLostCo 3 жыл бұрын

@@Hudlbuar All good! That was definitely something I was thinking about when rewatching that section, so I am glad you brought it up. Cheers!

@trentvlak 5 ай бұрын

Required tools: a socket set and a hammer. :)

@tom._.2318 2 жыл бұрын

I have a question. I have a 2021 Status and i want to switch to a coil shock. But one shock eyelid is 90 degrees different than the upper one so one is vertical and the other is horizontal. The shock is 230x60 but i cant find rockshox or any coil shocks with this design. Does anybody know what this shock eyelid design is called?

@TheLostCo 2 жыл бұрын

The Status has mounting hardware on the front (m8x30) and an open eyelet on the rear. As far as the rear shock mount being 90 degrees relative to the front mount, you can simply put something (a screw driver for example) in the rear shock mount and turn it until it fits in the frame. If that doesn't make sense, give us a call and we can describe it better over the phone. In short, a 230x60 shock with the right mounting hardware on the front, will fit your bike but you just have to turn the rear mount. (360) 306-8827

@tom._.2318 2 жыл бұрын

@@TheLostCo thanks 🙏 that realy helped me

@FedBiker 3 ай бұрын

No grease needed?

@neodporucam6347 2 жыл бұрын

guys, I need help, I ordered bushings from offsetbushings and theres no o rings, they’re weird and idk how to install

@TheLostCo 2 жыл бұрын

Please contact us and we can try and help! (360) 306-8827 // sales@thelostco.com

@offsetbushings5182 2 жыл бұрын

You do not need o-rings with our kits, everything you need to install is included. Hope that helps!

@yan-yansmtbjourney2759 Жыл бұрын

can I rotate the bottom eyelet 360 degrees ?

@TheLostCo Жыл бұрын

It depends on the shock, but generally speaking, yes you can. However, I'm not sure why you'd need to as rotating it by 90 degrees is generally the most you'll turn it. Check with manufacturer first or just give us a call or email at the shop and we can let you know! sales@thelostco.com // (360) 306-8827 -Mike