Hahaha!!! Ang galing, best scene yung 12:47 saglit lang pero row na row! Thanks pre!

Nice...plan ko rin bumili

Tnx Sa review sir tama tama balak ko bumili nyan Sa shoppe

Galing pinapadali ang cutting iwas ngalay pa ..

Ayus!. . .plan ko bumili nyan sir gene. May nakita ako sa lazada, combo siya with drill stand (which I recall from one of your vlogs as "basura"), less than 1k ang price. As of now, small diy projects pa lang naman ginagawa ko and wala pa ding budget para sa actual cut-off machine and drill press, so kuntento na muna ako with these. Anyway, thanks for the review, keep it up, stay safe & God bless. . .

Hahaahaaa may commercial..pero tnx a lot grabe dahil sau na assemble ko mag isa yung grinder stand na inorder ko sa lazada syrmpre...🤗🤗🤗ganyan na gayan sau yung nabili 508 lng ksma shipping..tnx tnx tnx🤗🤗🤗

Yung nabili kong stand medyo malaki ang play sa mismong pivot nya. Ginawa ko, disassemble and pivot assembly, made some measurements and 3D printed the 2 plastic bushings as replacements. Hopefully tumagal kasi PLA lang ang material na ginamit ko. And I agree, epic yung 12:47, hahaha!!!

With regards to cut using angle grinder with stand....I strongly advised to refrain from over-extending the "down-press" just to have a fast metal-cut...and why? you might asked.....Based on experience, madali kaseng masira yung spiral-bevel gear sa loob ng gearbox ng angle-grinder due to excessive "down-pressed"....iba rin kase kpag hand-held, you can estimate the amount of force-cut needed...also , i strongly recommend to open the gearbox of the angle-grinder and check the level of lubricant inside.....kahit bago pa yan sir, you will be amazed on the amount of lubricant put inside...Thumbs up and a New Subscriber here

sir kaya 1x2 na tubular? puro 90° cut lang

Idol dapat hindi mo binibilisan ang pg assemble paano nmin makikita ng maayos yan. Slowly lng dspat at bago mo ikabit close up ng kaunti. Suggestion lng nmn. Thanks.

Before fixing or detaching any parts specially near blade, ALWAYS plug off first sir..thats very unsafe.

Yung black and decker cordless drill nyo po ba 110.volts po ba nag order po kasi ako sa amazon ldx120c model may mabibilan kaya ako ng spare battery kung sakali dito sa pinas

Meron akong ganyan sir kaso di makaputol ng 90degrees at kelangan ng 5" diameter na disc para maputol ng derecho ang square tube..tumatama kasi ang ulo ng grinder..mas prefer q tlga cut-off saw para mas mabilis gamitin sir.

Sir, kaya po ba nya icut ung tubular na 1*1 ng diretso? May nakapag sabi kc na hnd daw nakacut ng tuloy tuloy ung tubular. Tnx po

Anong size po ng cutting disc gamit mo?

May mag sponsor dyan sir gene miter

Hello poh pwd puh bayan gamitin sa kahoy

Sir d nia kaya mag 45* n cut

kuya dun lang ako natingin sa mga kamay mo 😁 grabe prang kamay ng yeyemenin, hndi xa kamay ng DIYer😁 heheh

Gud day, sir anong brand ang mainam na disk cutter sa grinder..tnx po..God Bless..

mas safe ba mag cut kung may stand? at safe ba mag cut nang angle bar pag may ganyan?

Boss medyo matagal lng maputol

Hm

nice idol pa promote naman channel ko.haha.

Palitan mo malaki disc yun milwaukee 180mm na disc

musta to ngayon?

Gene anu nangyare sa 12:47 mark ng video? Haha salbaheng kanang kamay yan Lol

kaya ba ang 45 degrees cut dyan boss?

Tingin ko mas ok parin bumili nalang ng cut off machine talaga.. Medyo mahal nga lang.

tried this pero hindi maka 45° cut kinakapos adjustment.. walang kwenta

walang kwenta hindi maisagad ang putol. kagaya ng nbiki ko lotus. hehehe

Ang intention mo kaya mo pinakita ang lomvum na grinder kasi nanghihinge nanaman ng sponsor ahaahaha