Auto show in Erie, PA, looks like he changed a few of those in his lifetime lol.
Пікірлер: 7 000
@meh...4966 Жыл бұрын
This is honestly one of the most Honda-driver things I’ve ever seen 💀 homeboy did NOT hesitate to start fixing that head gasket. Mad respect tbh
@shortcurcuit5779 Жыл бұрын
respect? he doesn't have a clue what taking apart a motor when it's hot does to a motor. furthermore if he is carrying a head gasket with him he knows the heads warped or doesn't know why it keeps over heating or blowing as he put it. warped head or crack in head or block prolly from doing this
@meh...4966 Жыл бұрын
@@shortcurcuit5779 While you may be correct, most people would probably have no idea what to do and less likely have the tools on deck, so kudos for that. That being said, it blew my mind how this dude was not only taking apart this smoking engine, but also touching it with his bare hands. Dude’s got the spirit for sure! 😭😂
@aboveaero Жыл бұрын
@@shortcurcuit5779 enlighten me. What happens when you take apart a motor when it’s hot
@almostnorris623 Жыл бұрын
He looked like he was in a mad rush. The young man decided to break the rules by acting on the hot engine, and he proceeded ahead two steps further after turning off the engine plus opening up the hood. The young man looked rushed and for no apparent reason but crowd control most of them mechanics at the car show. He succeeded at the end, looking at the final ending of this clip with the engine finally cooling. This is a young mind at work folks. "I tell you h'whut" moments.
@gokuthatmadethebeat Жыл бұрын
@@aboveaero it causes a ton of wear on the parts and can crack them
@IAW_OPSEC9 жыл бұрын
You have to respect that he already came with the tools necessary to change, most motherfuckers would open the hood and just stare it
@killswitchxci25629 жыл бұрын
I always carry tools, I have everything but a air thank and air tools in my z33 ( 350z ) not only for me but other people that are broken down on the side of the road. comes in handy and saves a lot of money than paying for a tow truck
@marcunger8059 жыл бұрын
no actually most motherfuckers would do the job properly so this doesn't happen. being that he has probably done this a dozen times he feels like a hot shot being able to rip it apart on the spot. so he can look like mr pro ricer. I can fix my car anywhere because I can fuck it up anywhere lmao....he obviously has done this already cause he knows his work is shit and spur of the moment so he has gaskets with him. hmmmm does he reuse the head bolts lmao.. great job unknowing wannabe show off.....nnnnnnooooootttttttt
@bullet57609 жыл бұрын
No most ppl would pay to get the job done because most ppl don't know what to do. The bolts are fine as long as they don't reach their stretching point which is set a good margin above the torque point, and as far as we kno those aren't factory bolts considering he modified the engine so he may have stronger bolts. I never would have thought ppl who say they are mechanics would knock a guy for fixing his car on the spot because he had what he needed to get the job done honestly what mechanic doesn't have any tools in his car, I have well over 400 tools in my trunk that I'll need to work on my car or to help someone else out. The only thing I wouldn't do is not wait for the engine to cool down.
@MILANOKIS9 жыл бұрын
^^ No, he actually has more issues on his hands now when it could of just been a simple head gasket replace. Definitely will need his valves adjusted for it to run correctly and by seeing how he was just taking off random bolts, I don't think he has the knowledge to adjust his own valves.
@coltenW19 жыл бұрын
bullet5760 no he actually fucked that car up by doing it there on the spot...
@dw_drummer38286 жыл бұрын
I'm mostly amazed at how he is working on the engine barehands while its still hot as fuuuck.
@giselsanchez32773 жыл бұрын
Makes me think its a planned video, hear no breakaway with the gun :/
@stanley20043 жыл бұрын
While hot everything is easier to remove.
@sirseven3 Жыл бұрын
Don't touch it for very long 🤣
@Alexander_l322 Жыл бұрын
@@giselsanchez3277 that was a drill he was using lol it had a chuck
@tear728 Жыл бұрын
The power of sheer embarrassment
@BlackCatRedScarf6 жыл бұрын
The legendary field mechanic. The hero that makes cars finish and win really championships or saves vehicles and crews in the battlefield, but nobody talks about...
@szymon6207 Жыл бұрын
Be careful too much revs anyway
@robertokandal25 күн бұрын
hes more like a moron engine destryer
@robertokandal25 күн бұрын
the legendary engine destryer
@robertokandal25 күн бұрын
@@szymon6207 engine destroyer
@hozerveedubb_twosixx52966 жыл бұрын
Dude takes care of business and pays no attention to the “experts” just talking shit . Respect
@BarneyGumbl33 жыл бұрын
@Budget Boost DIY I pray for things to break on my motorbike just so I can fix them 😂
@jamothegreat60522 жыл бұрын
That's a great way to warp a head.
@itried2hard6332 жыл бұрын
@@BarneyGumbl3 exactly how i am with my civic, i look forward to oil changes because i finally get to work on it lmao.
@Billy-gh9ih2 жыл бұрын
@@jamothegreat6052 how
@jc199159 Жыл бұрын
@@Billy-gh9ih by disregarding engine timing and reusing TTY bolts.
@krocialblack6 жыл бұрын
Call this kid a ricer all you want... But at least he knows how to work on his own damn car, unlike the hotshot in the $200,000 RocketBunny GT-R who doesn't even know how to change a tire...
@chargermaster5866 жыл бұрын
krocialblack You can't fix modern cars once they go bad they are tossed this isn't grandpa's 1st car.
@DreamTeam-jx6hq6 жыл бұрын
krocialblack so just because you have money to buy a nice car you have to know how to fix it your self 😂😂😂. You got jokes.
@danielexpertyoyo6 жыл бұрын
Dream Team real car enthusiasts know how to work on there own cars ..wanna be car fools don’t know jack shit
@DreamTeam-jx6hq6 жыл бұрын
seethat M yes your right but just because he drives a nice car it doesn’t mean he should know how to fix it maybe they like the look of it or the speed or it. When you buy a home they don’t expect you to know how to build it. That’s like saying I’m a fool because I own a big home but don’t know how to do basic reapers on it or build it. You catch my drift. Yeah I hate wanna be car people too but I don’t hate on people who drive nice cars and don’t know anything about them.
@danielexpertyoyo6 жыл бұрын
Dream Team I understand your point of view I’m just talking about the people that have nice cars and act like a know it all and hate on every other car because it’s slower ...but others that don’t know it but just wanna have a clean car that’s alright because you can always learn about it ...that is alright if your only trying to learn more but when it’s in a situation you don’t know shit and you act like you know it all and you try to be a know it all but you aren’t that’s what triggers me lol
@bibleboy57225 жыл бұрын
I got nothing but respect for this man.Most people buy "customized" rides already customized.I told myself along time ago if I ever hit switches on a lowrider it will be built by me from scratch.I'm still watching Scotty Kilmer videos and learning,GOD Bless you all
@mariaechandi62575 жыл бұрын
Lol Scotty fan! cool He makes it seem like its no biggie x)
@desertrat1357 Жыл бұрын
First step! quit watching Scotty. He has absolutely no idea what he's talking about.
@MCFresh13 Жыл бұрын
Between Scotty and ChrisFix, I’m confident in my repairs more because of them
@CMONBUDDYSMH Жыл бұрын
I like buying quality custom cars at a fraction of what it costs to build. Only broke people rant about what your spewing lol….. Still give this kid props though but I’m not buying anything he’s building 🤷
@KumoGoesFast Жыл бұрын
@@CMONBUDDYSMH "i like taking a cheaper option that requires less work. only broke people take the more expensive option." what does that even mean my dude.
@kenny82956 жыл бұрын
When you watch Chris Fix it VIdeos
@stickerz79486 жыл бұрын
So true
@plainOldFool5 жыл бұрын
Hey Guy!.....
@aarontapatio22575 жыл бұрын
Lol
@ItsMotoMatt3 жыл бұрын
Who is "Chris Fix it?" I'm guessing you meant ChrisFix 🙄
@CarsandtheirParts8 жыл бұрын
At least he actually works on his own car unlike 75% of "tuners" who pay other people to do it
@TheLightningwrath8 жыл бұрын
man I wish I could work on my car. But I'm borrowing a car. When I get my own, I don't even know where to start learning v.v
@SuperSpetterpoep8 жыл бұрын
So any tuner should have all spare parts back in the trunk and able to fix head gasket on the spot? lol. Nothing wrong with maintaince on a proper garage. Pay a little more but get more.
@CarsandtheirParts8 жыл бұрын
+KronosSlots never said that. Apart from the fact that they totally rip you off for easy work, and the fact that most tuners will then try and brag about it even though they've never laid a finger on it.
@SuperSpetterpoep8 жыл бұрын
I drive a RS4 B5 with 440HP. It's for 2 years already under maintaince at my garage. If he would have ripped me off, i would know.
@AngelRmz13DjFino8 жыл бұрын
Do you know that person to say that he cant afford it?
@erikidoyaga8 жыл бұрын
I was ready to sit here for an hour or two and watch the man go at it. :(
@allanblazek62148 жыл бұрын
i know right this video is short
@Haderg338 жыл бұрын
I bet it only took him an hour shit he is fast
@karlx-18 жыл бұрын
Me too. More fun than watching him do his math homework.
@markmartinez90517 жыл бұрын
Hayden Gudmundson fast but torque specs dnt match nor the sequence of the bolts
@outwiththem7 жыл бұрын
Math speed is BS for a good mechanic..we have calculators....Some can do fast math..and cant change a lighbulb, or wash dishes without breaking something..
@gecko14065 жыл бұрын
Subie owner blows head gasket pulls engine jack out of trunk lol
@MikeComedies3 жыл бұрын
I'll have you know. Subaru's never blow head gaskets. In parking lots.
@123rez Жыл бұрын
Most kids his age would be crying and calling mommy and daddy. This kid is the man. Rolled up his sleeves and gotr done. Impressive. Wish more kids learn hands on skills.
@JasonTylerRicci6 жыл бұрын
It's amazing how much you can actually do on a Honda with only a 10mm, 14mm, and a screwdriver
@GR1MR34PER336 жыл бұрын
Jason Ricci and a torque wrench? I doubt he can just torque those bolts to just whatever
@LoveHandles694205 жыл бұрын
Jason Ricci the accuracy of this statement though lol
@jacobwebb88184 жыл бұрын
And gasket maker
@monkeynuttzgarage91114 жыл бұрын
Add 17 and 19mm and you can take the whole car apart 😂
@kellymc2394 жыл бұрын
Yeah, those Honda lawn-mowers are pretty easy to work on, and cheap. Thin metal, cheap parts, and lousy engineering make them a dream for repair shops....since they're in the shop all the time; nothing but profit when they see a Honda roll in (usually on a tow truck).
@billybobkeith91479 жыл бұрын
I have high respect for someone who knows their car. A lot of people have their work done for them. This guy is a true car enthusiast.
@GoatyHerps6 жыл бұрын
He is a car enthusiast because he can take shit off? If the video was longer, maybe, but so far all that's been proven is that he can remove bolts with a drill.
@GoatyHerps6 жыл бұрын
Mike - ...and if I asked my three year old where to go to change my brakes, he would know where to go. That doesn't mean shit. ANYBODY can take a car apart. Doesn't prove that he knows anything.
@GoatyHerps6 жыл бұрын
Mike - Did I comment on the title of the video, or did I comment on this thread? Yep... you sure showed me.
@RaineG5796 жыл бұрын
Mike ignore him. His argument is that a three year old could change brakes, but let me tell you something. Anyone can take shit off but diagnosis is a talent.
@queecakes54535 жыл бұрын
SPEED_ TRAP very true
@alejandrogerardo57254 жыл бұрын
Kudos to this kid for being able to work on his car,the rest of those “mechanics” would have just called mommy and daddy or a tow truck
@dfelixrx76 жыл бұрын
Think he even painted the car in the parking lot.
@Operator-fq2fn6 жыл бұрын
dfelixrx7 probly sold it there too
@Operator-fq2fn6 жыл бұрын
Thrishen Pillay yes and i build party busses and limos
@farerse5 жыл бұрын
i think he rebuilt the transmission on the spot too
@saadjahangir15164 жыл бұрын
Lmao
@kaybevang5363 жыл бұрын
@@Operator-fq2fn guys he’s building a mansion in the parking lot lol
@arxfortis74818 жыл бұрын
I love how all the "experts" are talking in the background and he mostly ignores them and keeps working.
@hassantalib34267 жыл бұрын
Arx Fortis agreed
@dm70976 жыл бұрын
Arx Fortis yes I love the guy who tells him that he's going to need some water now! Thank you captain obvious! Hahaha
@MrTravisAl6 жыл бұрын
"You might want to put some water in it." AND CRACK THE BLOCK, IDIOT??
@dm70976 жыл бұрын
Travis A ok two points 1) some people call anti-freeze/coolant water 2) the only way he would crack the block is if he leaves the plain water in there through the freezing weather. Seeing as how it looks like it's summer time in this video, the risk of cracking the block is slim to none.
@Joopsmann6 жыл бұрын
Yes! Give this young man an award for initiative and motivation. Focus too! Way to go, dude!
@GeneCarrasca7 жыл бұрын
This guy has dedication. How many of those guys watching him could fix the gasket on the spot?
@Deekilledyou7 жыл бұрын
None of them cause it's a stupid idea to change a head gasket on the spot. The motor is still hot so you can guarantee his head is warped when he removes it, He has a crowd around him so it's pressure on him and easy to break concentration, he didnt mark his Cams so when he puts it back together the timing is off, and why is he even going to a car show with a new head gasket (Let's hope he also brought new internal bolts cause they must be replaced too because they're tty bolts) know his shit is fucked in the first place??. I give him an A for effort but you don't do jobs like that on the street. I know it sucks to be that guy that has to have his car towed out the lot at a meet but he should have taken that L and just have it towed back home
@AlexGreenwoodUkulele7 жыл бұрын
I hope, at least, it got him home. Them torque-yields are a pain in the butt sometimes, but honestly, I'd rather bodge together something that'll work for a while and maybe cause damage to get home rather than have to spend a lot of money for a towwy.
@jonbertocchi1737 жыл бұрын
GeneCARRASCA only the dumb ones will
@holton3457 жыл бұрын
Even if he does all the work himself except for milling the block and head, the price of the milling work plus a replacement head will run him about a grand, conservatively. The tow home would cost about $75 if he is less than an hour away. And judging by the crowd and apparent location I am guessing he is less than ten miles from home. Personally, I would not "bodge" the job in order to look more manly, risking a warped or cracked head or block and minimum of a grand in parts and highly specialized labor (possibly thousands more, or just a replacement vehicle, seeing how that car probably would not merit thousands on a new head) when the car can be safely trailered home for under a hundred bucks. Having big balls is not quite the same as being a complete and utter fool to impress your friends.
@timmason25567 жыл бұрын
Holton 345 u guys for grt when ur young u dont care. U make it work and trade parts. U can get a jdm motor for 2k so y not fix it. This car will b run into the ground im sure
@foxisretrofitting45562 жыл бұрын
I remember watching this back around 2012 and was blown away by this. Nowdays I'm still impressed because now I have Hondas and I may be quick with a d series or f series sohc while its cold but this dude is amazing for being able to do all that while its piping hot.
@tortron Жыл бұрын
I'm amazed if he can get the head bolts out. Twice I have had 2 just immediately round off even with a new 6pt socket at the junk yards. Now I carry a set of nut grabber ones as well
@narutofanz4 Жыл бұрын
I love the feeling he has when he knows how everything works and comes apart. Great experience
@nugenki7 жыл бұрын
What a legend. My car has been in the garage for 3 weeks because I'm mentally preparing myself
@FREESMOKEUNLIMITED5 жыл бұрын
Nugenrules mine was for five years. 94 accord. Total dope. The head is right there like his I didn’t know tho.
@garryoak4 жыл бұрын
😂
@turbowank16v3 жыл бұрын
Hes a legend cuz he knows how to unbolt a cam cover?are you for real.he then proceeds to unscrew cam carriers whilst his cam belt is still on.this guy is no where near doing a head gasket on spot.not saying it cant be done but first he would run out of day light and second he would have to take head away for pressure testing and possible skimming.find it hard to believe that people who are car nuts actually know fuck all about car that this impressed you.
@JeffMcDuffie72MeridianGate Жыл бұрын
5 years later your car is still in the garage.
@nugenki Жыл бұрын
@@JeffMcDuffie72MeridianGate did not expect to be attacked this morning 😭
@funshootin19 жыл бұрын
good for him..most kids his age would be on the cellphone to mommy to borrow a credit card for a tow truck..self sufficient and has the ability to do a quick temp repair to get himself home..of course its not the right way but if it works for a while till he can setup the time and resources to do it right than I call it a win..Hes obviously been watching Roadkill on youtube and its madness is rubbing off
@bigwhitechevy25578 жыл бұрын
Roadkill is the shit!
@Kaasen98 жыл бұрын
+funshootin1 Yes, the guy in a video from 2010 was able to do a repair job thanks to a show that began in 2012.
@funshootin18 жыл бұрын
+Buddy I never looked at the date of post..guess ya got me but you and at least someone else know what roadkill is and got the dumb lead ballon of a joke anyway. thats comforting
@epfdnunjamunkey02588 жыл бұрын
+funshootin1 roadkill is the best show ever motor trende
@PS2Damon Жыл бұрын
Yeah people who admit they don't know how to work on something and leave it to a professional instead of ruining it more by trying to fix it are stupid huh? You sound like a fucking retard
@lonewolf35646 жыл бұрын
I dont understand these comments. Doing head job a b series integra is cake walk. Not hard at all... But why would you do it in parking lot/ track meet, without checking to see if the block or head warped. With the amount of smoke I saw coming from under the hood, it definitely warped something. That's a half ass job and it'll only happen again. Plus, you've got to replace the head bolts and do a valve job. Again... why would you do that in a parking lot, unless it was your only way home. Granted, I ended up doing the master ase tech grind for several years... But even before that, back in my younger (now ancient) high-school & early college days when i was into the whole tuning/import scene; i remember how my buddies and i used to rebuild heads, do motor swaps, b20 vtec/K series/h series swaps, and full builds in the driveway or by the side of the street near our house parked on jack stands... Ah memories. I feel like back then, because the import scene was still new and developing into what its become today, that a lot more people who were into the scene back then were more accustomed to wrenching on their cars and finding the best new way to make a little extra power. Call it Nostalgia, but back then there was a certain pride that went along w/ learning how to do it yourself and getting in there with your hands and seeing the results of what you built... As opposed to bragging about what you bought like how its become today. Its awesome to see that old school ideal still being kept alive. Regardless, how this kid did the head job, its fantastic to see him wiling to get down and dirty and fix it himself. I always believed that if you wanna have fun with that gas pedal, learn how everything on the end of it works and how to fix it.
@briansantos46376 жыл бұрын
I don’t get your comment are you mad about him doing it right there or not? Lmao
@ReMz101845 жыл бұрын
Lol this is like MGK's "Rap Devil"... was it a compliment or a diss? 😂
@kelo0ne5 жыл бұрын
"thats a half ass job it'll only happen again" why did you think he had the tools on deck ready to go again??? hahahaha
@FREESMOKEUNLIMITED5 жыл бұрын
Lone Wolf how long did the flintstone mobiles take to tune back then?
@4oh8cal Жыл бұрын
I like how everyone is amazed at the most simplest thing on earth, he knows what he's doing big deal lmao
@bloroxcleach7 жыл бұрын
We cant call this guy a ricer. He actually knows how to work on a engine
@peterveresan35916 жыл бұрын
Blorox Cleach hmmm common sense would tell me that you would never work on a hot engine, cause it increases your risk of stripping out bolt threads. But at least he knows how to take it apart, and I don’t actually know how hot the engine is, and judging by how he isn’t screaming at grabbing the bolts, yeah it’s not that hot, but it could be hot enough to strip out some threads maybe?
@sieve56 жыл бұрын
Clorox bleach is the best user on youtube, salute. Great taste in videos.
@scdevon6 жыл бұрын
How much could he know if he's loosening the head bolts on a hot engine and he drives around with cam cap bolts stripped and missing and he is reassembling an engine with unknown warpage on the head and block?
@AcuraLvR826 жыл бұрын
Removing an aluminum head on a motor that hot will result in severe warpage and thus another hg failure soon down the road.
@timowens5026 жыл бұрын
*an
@ZEDNANREHIGH8 жыл бұрын
What a Tease, I was ready to see the whole video.
@angelcobian59187 жыл бұрын
lowkey lol
@roycehellion7 жыл бұрын
Especially in the 3 minutes it was recorded. I was anxious to to something really cool or epic fail.
@arifftupar29386 жыл бұрын
He got that skill but not that money. So for those of you who called him ricer. Get a life
@airta896 жыл бұрын
It's awesome that he knows how to do it and that he had the tools to do it on the spot. All that aside, I wouldn't recommend changing a head gasket on a hot engine. Especially if it's an aluminum block and aluminum heads.
@danielkowalski1432 Жыл бұрын
I mean it would probably works better when he changes it on hot engine. When engine is hot, the metal gets bigger, so when he put head gasket right now and screw it back together it will be tighter when it'll get cold so it should last longer.
@deedle6073 Жыл бұрын
@@danielkowalski1432 It's supposed to be torqued to spec, not tighter the better. In fact, he probably blown the gasket due to improper assembly.
@RothBeyondTheGrave Жыл бұрын
@@deedle6073 my thoughts exactly.
@scurling29938 жыл бұрын
Those smart guys commenting probably can't even turn a wrench.
@GoatyHerps6 жыл бұрын
My Videos - Is that that star shaped thing that takes nails out?
@sethc7586 жыл бұрын
My Videos lol "it probably needs water". yeah pull that cap off while it's boilin bud
@poppabloodvessel70726 жыл бұрын
Wrench=spoon?
@cchagan086 жыл бұрын
I'm left handed and my friend said I bought the wrong wrenches. Do you know where to buy a lefthanded set??
@MidWesti9 жыл бұрын
no need to hate really.. i drive an STi and have had hondas before.. sure it sucks that his shit blew out, but at least he has the confidence and know how to fix it to get him home. Most the ppl on here woulda had to have mommy call a tow truck to get their car to the mechanic. plus thats one of the nice things about hondas.. everything is right there, easy to get to. it's his car in the end, so dunno why anyone needs to bash the dude.
@clipsedrag139 жыл бұрын
U wouldn't be tearing an sti apart like that... Huge cluster fuck in those engine bays
@MidWesti9 жыл бұрын
Nick Brown hahaha you got that right! If I did, it would sure as hell take A LOT longer than a Honda engine bay that's for sure! Honda is simplicity at its finest. I've got a 2000 si that I gave my wife, and I would MUCH rather wrench on that!
@migy6709 жыл бұрын
MidWestBrick I would of call a tow truck . He does have balls but he is really stupid . He just started ripping things apart not knowing what the actual problem is or putting them in the correct order like the spark plug. but yeah it his car though. just gotta make that point
@DumbassPlumber9 жыл бұрын
This kid should have called mommy because he doesn't know what he is doing. Atleast let the engine cool down before you take it apart and fuck it up.
@migy6709 жыл бұрын
Aye he had to take that blown head gasket that he apparently known lol . Time is money haha
@Jt_1z Жыл бұрын
No one is built like this anymore. He defines the “Built not bought” slogan. Legend!
@gordonmcmillan55566 жыл бұрын
Real man would have done it with the engine running.....
@ScubieFlow6 жыл бұрын
Gordon McMillan yes well can’t run with no spark plugs now can ya? Well shit.......
@gordonmcmillan55566 жыл бұрын
TheWhiteBuster whoa sarcasm alert.....
@ScubieFlow6 жыл бұрын
You would be surprised on how some people think. Wouldn't surprise me anymore.
@ScubieFlow6 жыл бұрын
Oregano lol you mad
@zeelong15896 жыл бұрын
Lol
@terrybarronjr.83678 жыл бұрын
Legend is, he's still there fixing it till this day
@Sam_S2k8 жыл бұрын
Lmao!!!!
@BoostedPastime7 жыл бұрын
LOL
@shawno17507 жыл бұрын
1 year later, he still at it. this time during a high pursuit.
@arielzawadzki62877 жыл бұрын
Lol
@spaceghost36966 жыл бұрын
LMFAOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO CMON MAN! I'm in the library.
@ranchhandrandy32136 жыл бұрын
This actually makes me happy to see. Young man knows his car. Good on you.
@berrex5152 Жыл бұрын
love how he just pays no one any mind and just does his shitt.. i respect that so much
@InitialEngineers4 жыл бұрын
I love how all his cam cap bolts are all hand tight 😂 same probably goes for the head bolts , no wonder the headgasket blew lol
@josemares1439 Жыл бұрын
Motor is hot
@HelterSkelter117 Жыл бұрын
I was thinking the same thing. He was able to remove the head bolts with a cordless drill instead of an impact driver. Bolts probably weren't torqued at all.
@QisKarma_ Жыл бұрын
@@HelterSkelter117 you can see he crack them loose with a ratchet before using the drill/impact
@QisKarma_ Жыл бұрын
@@HelterSkelter117 to be fair though they weren't nearly as tight as they should be but the ease of getting all that off could be be due to heat
@mitchellthibeault67598 жыл бұрын
looks like he's done this a couple times
@tteuvky7 жыл бұрын
Was thinking same thing or maybe he is mechanic
@uncleweirdbeard867 жыл бұрын
Its not hard to know how to take apart a motor and put it back together, and as far as I'm concerned, Doing it on the spot is a good idea as it is cheaper than a tow and doesn't risk doing more damage
@Jay-gs5xg7 жыл бұрын
uncleweirdbeard plus you get to leave the mess for someone else.
@Straight_White_Fatherly_Figure6 жыл бұрын
Am i the only one surprised seeing him take the smoking hot engine apart with his bear hands?
@mr.mckinnon56806 жыл бұрын
Something tells me he's done that several times. And from the looks of it he's probably the only Honda technician that could actually make money doing head gaskets on those pieces of shit
@maniacalmango9 жыл бұрын
Not a Honda fan really. But have to give this guy some credit for just saying "fuck it, I'll do this shit right NOW" lol. And for you haters, keep on just putting gas in your car and not knowing how the combustion engine even works.
@maniacalmango9 жыл бұрын
***** Yeah, weird! I've only had 1 Honda, 1990 prelude si all wheel steering...now that's weird! Bought it off my neighbor for $300 after she threw the timing belt. Drove it for over a year with 3 bent valves, decent little car and fun to drive.
@TedMan559 жыл бұрын
Sean Phillips FWD is inferior to RWD. I don't like Japanese cars, but if you're going to drive them, at least drive a Supra or Skyline. Not shitty civics. And despite your VTEC, you still can't make any power without blowing up your engine.
@maniacalmango9 жыл бұрын
Teddy Shinozuka I personally drive German Engineering. I don't hate on any car really,i just give the respect they deserve. Vtec is actually pretty cool in the way it works and can make some good power and be durable if done correctly. I'm a true enthusiast and won't knock anyone's project or preference,although if they start getting tacky with autozone peel and stick stuff I might give them some advice.
@RetroAdzz9 жыл бұрын
Sean Phillips and of course the Mini is British
@jeff74619 жыл бұрын
RetroAdzz Mini is owned by BMW
@shazrinsalahuddin22255 жыл бұрын
Respect to u bro..u know ur beast...not like others outside just talking like the r king of tuners...salute...
@JohnnyCage4Real6 жыл бұрын
He's got my respect. Any carguy who truly loves his car and what it brings knows what I mean
@LanceCampeau8 жыл бұрын
Now that's a hot swap...
@NRGpony9 жыл бұрын
Most of the people bitching about it being a honda more than likely don't even own a car in general, or have a drivers license either.
@sacr39 жыл бұрын
***** Dodge Challenger owner here, I bitch about ricers. Not all Hondas I bitch about but specifically the Civic I do - simply because so many boys run around with their civics with their cherry bombs, annoying everyone. I get it, the muffler makes it sound "cool", "better", might "free up some horsepower" even though most engines are designed with the backpressure in mind. But christ, who wants to hear a tiny engine rev? Like listening to a lawnmower.
@NRGpony9 жыл бұрын
Tiny engines, thats the price you usually have to pay for lightweight import, I never justify exhaust systems unless there is ATLEAST a bigger intake manifold. You can get some decent mufflers that don't have that ear shattering rattle, but thats not what this is about. It's about these stupid kids who don't know that all cars have potential, if someone out there made a hyundai with 1000+HP there is DEFINITELY no reason you can't do it with a honda engine which has one of the largest aftermarket options available.
@123crackerjacks9 жыл бұрын
***** Did you seriously just say that the Celica was great? xD 2003 Acura RSX owner here and I bitch about ricers because they give real car enthusiasts bad names. It's not about what car you drive or what style you prefer. It's how you act and how much you care for your car. If you care for your car then you wont put on a $100 body kit. A car can't be a ricer, it's the driver. I've seen plenty of Domestic ricers.
@123crackerjacks9 жыл бұрын
Obviously you don't know much about them. I can get a nice turbo kit for $1600. An ecu management for $600, and misc parts around $300. D series honda engines are shit. B series is when they started getting serious. K series is in my opinion their best motor. The k24's are beefy and can handle plenty of boost. K20's are good for high RPMs and can also handle a lot of boost, but have .4 less displacement. I'm not bashing on you either, i love the Focus ST's and I can't wait for the RS to come to America.
@sacr39 жыл бұрын
But guys....guys cmon.. its still a civic.. You can squeeze out over a thousand horsepower in these little 4 bangers, sure, but.. no matter how much you polish a turd, its still a turd.. What was it, Fast and furious that made boys go mad over the little 4 bangers? If you grab a nice base car, with good looks, a solid build, a good name and then spiff it out with turbos etc, hey, nice. But a civic?
@am74343 Жыл бұрын
I think it's funny that this came up on my KZfaq suggestions... In 2023. 😂😂
@o-cedar6993 Жыл бұрын
10 years later this is still impressive
@ArcadeGames10 жыл бұрын
I changed my own tire one time, beat that.
@MOSESOHD10 жыл бұрын
MkBopMw don't mean to show off but I refilled the wipers fluid
@mab0r0shi5710 жыл бұрын
Moises Herrera bitch please, i turned the key
@astonmartinridin10 жыл бұрын
***** I put gas in my car :)
@ArcadeGames10 жыл бұрын
Moises Herrera Somebody always has to one-up me. *sigh*
@Dr0idtehboss10 жыл бұрын
ArcadeGames I changed my oil once.... well I watched some one change my oil once...
@chrisanderson16359 жыл бұрын
I love all these 14 year old forza motorsport playing fanboys running their mouths when they've never taken a wrench to a car and probably never will lol
@americanpatriot36679 жыл бұрын
Most probably never even took a lug nut off of a tire either
@mrmetal1980s9 жыл бұрын
gotta start somewhere. maybe a parking lot isnt the best place though..
@chrisfitch34649 жыл бұрын
He looks like he knows what he is doing, kinda. He should have a torque wrench instead of the crappy impact and should actually let the engine cool down first or his head will warp when he try's to take it off
@TheHardcore4299 жыл бұрын
chris fitch that's not an impact.
@xCrossxGravex9 жыл бұрын
chris fitch and you don't use a torque wrench to break a nut.
@TheRealBootyWarrior3 жыл бұрын
Ive seen this video many times and always wondered what type of person would do this, 11 years later, i got the answer, my brother is this crazy lmaoo
@DG-EditsYT Жыл бұрын
This is motivation you get when this is your only ride home
@stevea59857 жыл бұрын
These guts laughing at him for fixing his own car . But hey atleast he can
@massimomax32157 жыл бұрын
that is not fixing it, it holds some 100 miles and it blows again if done like this guy.. to do that work properly u cant just pull head off and put a new gasket on it.. lol
@dr.mohammed15027 жыл бұрын
ummmm yeah u can?? as long as u didnt crack or warp the head especially on a honda b18b1 those motors run forever
@TheSqeeek7 жыл бұрын
Depends on why it blew. If your forced induction blew out the gasket because you didn't torque it down hard enough, that's one thing, but if you have a stock motor and blew it doing a burnout you probably warped the head at least a little bit.
@dr.mohammed15027 жыл бұрын
Lol just torque it down 10lbs harder it will seal..
@fakiirification7 жыл бұрын
they are probably laughing because a head gasket is serious business. you dont just swap it out like a radiator hose. its a machine shop trip at the bare minimum. or if your REALLY hard up for cash, you can do it ghetto style with a big sanding block to clean up the mating surfaces, assuming they didnt warp when you blew the gasket in the first place.
@johnkilo310 жыл бұрын
Based on how shitty that Integra looks I'm going to go out on a limb and say it wasn't put together properly in the first place.
@ryanwalker938210 жыл бұрын
Lol I agree
@jhonkafirk9 жыл бұрын
At least those camshafts looked clean... Shitty car but the kid takes care of it.
@mikeg35299 жыл бұрын
Jhon KafirB Did they look clean???? Dose he take care of it?? No one who takes care of their motor leave shit like CAM BEARING CAP BOLTS missing... I see atleast two of them non-existent as soon as he pulls the valve cover...
@jhonkafirk9 жыл бұрын
Michael G LOL I just notice the missing bolts...haha
@WhyDidYouTurn9 жыл бұрын
guy probably never even heard of a torque wrench!
@nigelcarren6 жыл бұрын
I once changed a sump gasket and water pump on a Mk1 Cortina GT engine in the hold of a ferry from Spain to Morocco in total darkness, with only a borrowed AAA keyring-torch to illuminate the proceedings. I admire this guy... sometimes there is NO other option. BRAVO... hope he made it home... He must have a hot date... There is no other reason for working this fast.
@tinman3784 Жыл бұрын
I love how he used a fishing tackle box as a tool box, you know this dude is resourceful.
@abeeftec10 жыл бұрын
We don't know if this kid actually finished or towed the car away. Fucker could have had a great video for how to change a head gasket out on the road but instead I wasted my time watching a guy remove some screws.
@Guzzetify10 жыл бұрын
It's the easiest shit ever, him changing it isn't even a big deal.
@evilcowboy10 жыл бұрын
to be honest he probably blew the head gasket by not doing it correctly to begin with. I see no torque wrench and unless he remembered the tightening sequence thats another issue. And those things are critical to doing a head gasket properly. He gets as far as removing some bolts for the two cam shafts. Which would concern me that he may not know to even time the engine which is another issue. Doing that kind of stuff on the fly is never a good idea because there are just too many things that can go wrong. You wouldn't have wanted to see the rest of the video unless you wanted to know how to do it wrong. And yes there is even a sequence to removing the bolts in which he totally ignored. Also obviously he has replaced the head gasket before. The problem is if it blew again then there is a reason it blew again. Most common not doing it right to begin with. I can guarantee if you asked him how to measure the 9 points to check for flatness on the head he would look at you like you had a 3rd head. You almost always have to machine or lap an aluminum head when changing a head gasket. Lapping is the more precise method so long as it is done on granite or glass that has absolute flatness. I got a pontiac head to 0.0015 flatness all the way across including between the cylinder walls. As a result the gasket out lasted the car. The frame rotted before the gasket did (Northern car).
@GreatValueJohnnySins10 жыл бұрын
evilcowboy Dude stop you are making these guys heads pop. All they know is if they see bolts then you loosen them then fuck shit up then tighten them and then say they fully built the motor... lol
@evilcowboy10 жыл бұрын
Brian Langdon lol very true. Seen a many cracked heads from over tightening. Also just saw a cracked bolt hole from a starter being held on with 1 bolt (95 sentra) after it snapped the starter fell away from the top of the tranny and would not engage the flywheel. You could hear it when the kid tried to start it just grinding away against the teeth on the flywheel. Too bad it was a new flywheel and clutch. Yeah children shouldn't touch big boy toys lmfao.
@Rhidongo10 жыл бұрын
evilcowboy If it makes you feel better, my neighbour managed to flood her fuel-injected car. She was that stupid. Also, I hope the guy with that shitty Integra has no friends. That shit is gonna be the death of him.
@bgtheo78917 жыл бұрын
now me and the mad scientist have to go in there and replace the piston rings u blew.
@pullurslip7 жыл бұрын
This isn't fast and the furious
@bgtheo78917 жыл бұрын
PullUrSlip yeah it is
@DutchBane6 жыл бұрын
Fato putso fried*
@sargeghost1516 жыл бұрын
Fato putso now me and the mad scientists have to pick apart the block and replace the piston rings you fried*
@blackstardragon_6 жыл бұрын
Epic
@gavinhogberg Жыл бұрын
Why are the "experts" around him even talking shit? He's doing it and clearly knows what he's doing
@chriswhoop Жыл бұрын
I got mad respect for a guy is willing to warp his head as soon as he pulls those head bolts
@GameTieTV9 жыл бұрын
overnight parts from japan couldnt even fix this lol.
@Tro10869 жыл бұрын
HAHAHA this made me laugh so hard!
@GameTieTV9 жыл бұрын
haha glad i got some laughs out of it :)
@aracecar46279 жыл бұрын
GameTie i dont get it... lol
@Cris55989 жыл бұрын
Hahaha good one dude
@Sebastianrogersmusic9 жыл бұрын
hahahah
@sanj50269 жыл бұрын
Ricer this ricer that... Who gives a shitt. If that kid puts on a fart can or a GT wing spoiler on his civic.... His loss not yours lol. Weird guys on here
@1tokeover9 жыл бұрын
Bouge laal You are a weird guy
@sanj50269 жыл бұрын
1tokeover lol I still get more bitches then u
@tvrfly576899 жыл бұрын
Bouge laal lol
@SEADiablo9 жыл бұрын
***** What do you drive or aspire to?
@MuricanMiata9 жыл бұрын
***** Lol lets run em. My cars just an old rice burner.
@robf7537 Жыл бұрын
It s a weird flex like being able to change all your house light bulbs every week, the real question is why and why not solve the problem instead 😂
@Hotdog_pimpin6 жыл бұрын
I ate a whole pack of English muffins while I was on my way to meet my parents for breakfast
@thatsyrianguy4875 жыл бұрын
Respect
@Reply_if_you_gay5 жыл бұрын
Does the breakfast know you cheated on it with the muffins?
@ursusarctoshu36387 жыл бұрын
Dudes probably got like 900lbs of spare parts and tools lol
@mauidude36 жыл бұрын
Ursus Arctos Hu full lifetime warranty on everything plus Jack stands
@jjcardinale13676 жыл бұрын
and still won!!!!
@kellymc2394 жыл бұрын
Especially if it's Honda, or any import.
@JohnathanFx9 жыл бұрын
Anyone who actually knows what the fuck there doing knows that he's doing it correctly....well the fast way anyways. And about starting with the belt.....you can reach the timing belt tensioner from the side through the cover with out removing anything. 1) Set TDC or mark belt and cam gears. 2) Valve cover 3) Remove cams 4) Disconnect everything from intake manifold. 5) Remove head and intake together. 6) Clean block replace gasket ....2 hours later RIDE.
@WTGRacing9 жыл бұрын
then after you put it together you have to check valve clearances.
@JohnathanFx9 жыл бұрын
You can but clearances are not change when you remove the rocker arm assembly.
@WTGRacing9 жыл бұрын
Johnathan B Really? usually i always have to change the clearances. I must be doing something wrong....
@JohnathanFx9 жыл бұрын
The rocker arm assembly comes off in one piece no need to touch the valve adjustment screws. However now would be the perfect time to check the clearances.
@winstonwolfe39259 жыл бұрын
Johnathan B I wouldn't give him credit for what i saw. It was ballz but definitely not professional grade work. A blown head gasket can quickly lead to other problems, so slapping another gasket there isn't make it all better..
@darrentylor5473 Жыл бұрын
"Now me and the mad scientist have to rebuild the piston rings you fried!" This guy, "Hell no, I'ma do it myself!"
@githinji123 Жыл бұрын
Legend. Mad respect.
@mattwolf76987 жыл бұрын
He replaces one after every time he drives the car.
@Scooter_built4 жыл бұрын
Matt Wolf it ain’t a Subaru 😂
@tonyknightsecreto83384 жыл бұрын
Hey you all ! great video I was just wondering it would of been nice to how gets cam sprockets off with out taken off the timing belt and timing cover can somebody else show us or is just time consuming thanks tk.com
@Kurzawaa9 жыл бұрын
At least he works on his own car...Unlike most of the people there.
@ghostrider62676 жыл бұрын
Eryk Kurzawa totally agree!
@ShaneCarles6 жыл бұрын
He was probably running Nitrous. This is the newer 96 body style Integra. I've owned Hondas my whole life, including the 1990 Integra. With this engine. It was a great engine in my opinion. It produced tons of power if tweaked right. If you treat them right, they treat you right & I tore that thing up. I went through transmissions more than the engine. Never had to do much to the internals of the engine, other than change the timing belt. Do tuneups and oil changes. The only problem with the 5 speed manual trans in these were the differential. It had a spider gear with pin type. That pin would wear out the gear and throw itself out, ripping the trans housing in half while locking up the front wheels. lol. This was later resolved with the Helical Differential. Solid, no space in between gears or open case. No pin to shear and rip the trans appart. After that, I really didn't race it, I used it to work on cars on the road. I pulled a trailer behind the car, loaded with my tools. I had air, a ground lift. Everything I needed to pull the entire drivetrain out if needed. And this Integra pulled that stuff with NO problem. Even on long distances for filling in at a Acura dealer in another city. Not just Hondas. Everything. Now, I work in computers & drones. A lot of electronics. It's a much cleaner environment and not as hard on the body. Working on cars is not an easy job.
@aleccooks6 жыл бұрын
Phone > tripod > best repair video that could have existed on yt
@TechnicolorWrench7 жыл бұрын
To all those saying that this kid deserves to be respected because hes fixing his car while everyone else stand around and watches you should pay attention. First off look at the camshaft caps, half of them are only held on by one bolt, while the other is completely missing and there is no need to pull the cams in the first place. When he pulls the valve cover his oil is smoking indicating that it overheated big time, pulling the head while its hot is without a doubt going to cause it to warp and his new gasket is not going to do anything at all.
@freakymrq5 жыл бұрын
to pull the head on my mr2 you have to remove the cams to access two of the head bolts
@onefastegcoupe5 жыл бұрын
@@freakymrq yeah n it gon be steamin either way a little from blowby from headgasket failure
@freakymrq5 жыл бұрын
@@onefastegcoupe not saying that the dude was right to start ripping his head off immediately, cause he's not, should let it cool down and do this at home or in a shop not a parking lot. Easy way to get hurt imo
@boostedsc4040 Жыл бұрын
@@freakymrqyeah my 2jz is like that and so is my s54, you have to remove the cams for proper access to the head bolts. The m3 was pretty easy to get the head off and back on but the sc300 you have to have a thin wall 1/2 deep well socket for those head studs on the 2jz I will never forget that for all the trips it made me take. But a lot of Honda engines you don’t need to pull the cams out of when you take the head off, my friend used to have a boosted d series civic and we pulled the head off and did the head gasket without removing the cam but that also cause they’re was a lot more clearance since it’s only a single cam
@boosted2.4_sky9 жыл бұрын
Let's all stand and watch...Sheesh...help the guy!
@ProfessorFatMan9 жыл бұрын
Hell no. That shit is fucking hot. I'd be glad to help but only when it's cold. But considering its an Integra I think it's a waste of time.
@Professional_Youtube_Commenter9 жыл бұрын
the guy knows what he's doing. How can anyone help?
@boosted2.4_sky9 жыл бұрын
OnlineBackupServices yeah I guess...other people would probably slow him down...going like a madman..lol
@GIitchclan129 жыл бұрын
OnlineBackupServices He knows what he is doing? He is removing the camshafts of the vehicle while the head gasket is located between the cylinder head and engine block.
@davidskala76529 жыл бұрын
Shane Smith you do know on the b18a1 under the cam shafts would be the head bolts so it would make perfect sense to pull the cams to pull the head lol
@2vcrew782 Жыл бұрын
Just so everyone knows. This is my generation right here! Notice the Hollister shirt lol😂 This has to be back in the early 2000s. That’s a man that knows how to get it done.
@danhirtle7825 Жыл бұрын
Had a friend in HS in the 70's who's dad owned an industrial turbo rebuilding shop. This guy would drive his mom's Plymouth Duster w/ straight six motor to school and back. One weekend he "borrowed" a small turbo from his dad's shop and cobbled it onto the Duster. No waste gate. He spent the next several lunch hours racing guys with muscle cars from light to light. He would bring a handful of pushrods along to replace the bent ones before he drove home after school. He pushed a rod through the side of the block eventually. Fun while it lasted though.
@SouthernMechanic6 жыл бұрын
Did anyone else notice that every other camshaft cap bolt was broke off? If say that isn't his first rodeo with the head gasket, bad thing is that it prolly keeps blowing because he isn't using new tty head bolts and I'm sure the head has been warped for a long time and he hasn't taken it to a machine shop to be shaved so this will inevitably happen again
@danielgapper83596 жыл бұрын
But hes getting home tho
@shitarse1006 жыл бұрын
Thought exactly the same
@troywarren10756 жыл бұрын
Can of stop leak will fix it fine.
@troywarren10756 жыл бұрын
@big balls999 either learn from someone who knows better or keep doing the same stupid stuff. It is true stupid is as stupid does. No disrespect in that.
@asdgasdf95806 жыл бұрын
All he needs is a cup of rice in the radiator and she'll be good as new
@MrUnderEstimated9 жыл бұрын
i want the whole vid
@mkb3580 Жыл бұрын
Give this kid some props man!….probably has all the necessary gaskets in his trunk…100% youngster!!…. kids nowadays would call their mom to get a tow truck…
@Mr-Clark Жыл бұрын
Instead of just calling his dad to get a tow, this young man made things worse by tearing his engine apart on the lot to save face. There’s no shame in asking for help.
@grimizzi71510 жыл бұрын
I love seeing Honda's blow up, I don't know why but I get a little kick out of it.
@fredd29810 жыл бұрын
So why does it cost like $2000 to have this done by a mechanic?
@cakefaice10 жыл бұрын
A whole head set can be around $60-$120. Mechanics like to charge $300 an hour for labor.
@cougar10ag10 жыл бұрын
Because shops have bills to pay for tools, equipment, rent, and the warranty you get. Oh and they're not hacks like this fucking kid. No wonder he's done it more than once. Maybe if he learned to do shit the right way he'd have only done it once.
@cougar10ag10 жыл бұрын
Cake Face lol have you even priced a head gasket set? $200+ plus another about $100 for head bolts. And labor is not $300 an hour. Job is probably around 8 hours. Plus the cost of machine work on the head. Only an idiot would change the head gasket and not get the head machined. And add in all the other extras like a timing set, water pump, spark plugs, and fluids.
@cakefaice10 жыл бұрын
cougar10ag A common I4 honda/toyota/chevy/whatever isn't $200+ for a headgasket set alone. A complete gasket set is around $60. Unless you drive a BMW or a V6/V8, you're not going to wreck your wallet on just the gasket sets alone.
@777jonah88810 жыл бұрын
its the labour to get to the gasket and replace all gaskets on top
@MrKiet764 жыл бұрын
That's no kid! That's the REAL MAN fixing his car on the spot while the kids watching! I bet half of them don't even know how to
@ElectricPulse1006 жыл бұрын
Legend says, he fixed it in 5 mins and still beat the other toddlers to the car meet.
@knobovsossidge20228 жыл бұрын
How come he drives around with a spare head gasket and all the tools to change it?
@zac92608 жыл бұрын
It probably happens all the time. Maybe has a second b18 in his trunk as well 😇
@hondagame70698 жыл бұрын
+Knobov Sossidge i think he faked it for attention
@xxKILLERIMPxx8 жыл бұрын
+Knobov Sossidge because honda
@TEAMCREAM_968 жыл бұрын
+Killer Imp because warped head
@emiliocornejo698 жыл бұрын
well personaly as a street racer when ni bprder gasket kits i always order a second kit just incase sonthing needs replacing on the spot incase somthing messes up
@mishlerdennis8810 жыл бұрын
Thats a REAL HotRodder, fix it on the spot no matter when or where. Hats off to ya arbachu not many of us left doing things the old ways.
@arockpcb13473 жыл бұрын
Nothing but respect for this cat, go ahead and shine. Fuck the haters
@johnhomi8834 Жыл бұрын
KZfaq algorithm brought me here 12 years later. Just now seeing this in 2022.
@richiestatham64549 жыл бұрын
Honda is a very reliable car so what the fuck are u people on about saying it is a shit motor
@VoraciousPhantasma9 жыл бұрын
Devil's advocate here: reliability alone never won any races, and unfortunately that and cost are the only two things Hondas have going for 'em.
@krannification9 жыл бұрын
***** I think those hondas are good cheap fun fwd car but yeah after a while you get bored of the fwd layout...
@VoraciousPhantasma9 жыл бұрын
krannification This. I spent a year helping a friend supe up his Civic hatch. Turbo'ed, it was around 185 bhp and you could spin the tires like nothing, but it wasn't as much fun as my 130 bhp RWD Miata because it was FWD. Oh, and the Miata cost around $3k less than the Civic + mods.
@krannification9 жыл бұрын
Yeah you cant get really sideways (excepting with handbrake) and it tend to understeer and usually torque steer a bit too. They can be nice for drag racing but not that much for track/rallye and we dont even talk about drifting... and we gotta admit it, doing donuts or drifting is much more fun than fwd burnout that can only go straight lol.
@Professional_Youtube_Commenter9 жыл бұрын
they're ususally not meant to be supercharged to get 2x the bhp. that's when they fall apart. Having said that every car wil break aapart at 2x it's bhp. The problem is ricers start of with such a entry level, cheap car and put a big ass supercharger in it, that they tend to have a bad reputation
@kevinchang5228 жыл бұрын
if he still went home with it I give him mad props cuz most of these car people won't be able to do what he doing
@muntuable6 жыл бұрын
hmong azn son exactly. And they won't even spend a hours looking into how to build and maintain they own stuff. They'll just keep riding maybe look at a few race clips ( bs)but never really get into the research side. But I realized just like one of the other guy say the new school millennium's(some not all) and old school fart were brought up different. They had to fix things on there own(less shops and rights of passage as a man). nowadays some of those parents haven't taught their kids it and those kids have no desire because video games and everything else made it so simple even with KZfaq. People have no desire to retain it because you can look it up at anytime.😔 let the others laugh theirs one in ever bunch( but some are even envious)
@a.l.26696 жыл бұрын
If you relieve the tension while the engines hot it's at a higher risk of warping the head. It's a waste of time, energy, and money to replace something if you're not going to do it properly the first time.
@Straight_White_Fatherly_Figure6 жыл бұрын
I know mine woulda been towed home or to a shop for sure lol
@npc-nt1jp6 жыл бұрын
Some say hes still changing out thay head gasket till this day
@markwatney86415 жыл бұрын
by some you mean those guys standing around shooting the shit? did they not go home yet ?
@TheRedRaven_5 жыл бұрын
(Pulls a few bolts) “Yooo respect kid, everyone else is just hating bro” Only people giving this man respect are untrained eyes that see a guy with tools pulling bolts. Those same people have a hard time swapping a battery, let alone doing an oil change.
@benjaminward52958 жыл бұрын
Yea very enthusiastic but probably will blow another without resurfacing the head. End of the day he still gets his car home this way.
@letsgettipsy858 жыл бұрын
yup u know wat ur talking about..thats exactly right i had machine shop experience so i can vouch
@zzzhuh8 жыл бұрын
X'D
@PunkAss173318 жыл бұрын
The threads in the head for the cam cap bolts aren't going to last to long either if he keeps jumping straight to untorquing them without taking tension off the timing belt first...
@nickpike90607 жыл бұрын
integras are gay
@TheSamplebridge7 жыл бұрын
and most of his parts probably didnt line up exactly when he put it back together. probably warped most of the bolts from the heat. i would've let it cool down first. then again i have a v8 and can make it home on 4 cylinder. just pull the spark plug out of the affected bank.
@esperanzar.57706 жыл бұрын
Reminded me of my dad with his truck always Under the hood doing it himself!Miss the good old days 😟
@FREESMOKEUNLIMITED5 жыл бұрын
Esperanza R. What happened to them? Is he not under hood anymore or not doing himself? You cant be so awesome then say something like this but not say where the good ol days went! I hate you so much rn!
@jackwatters95024 жыл бұрын
Paint Thinnerz Music Group TV He’s probably dead asshole.
@brianj52615 жыл бұрын
Now that's a trooper.. No hesitation, no complaining, just determination and action..
@NP-ek7dl Жыл бұрын
Built not bought! Real boss ! Respect the man
@reladham10 жыл бұрын
I love it, everyone else was standing around talking their intelligent nonsense and this kid jumps in to do a major engine job before the fresh steam even clears. THat is the no nonsense way to do it.
@777jonah88810 жыл бұрын
its a head gasket man!!! - you wait till the engine cools and is one temperature before starting if you want to do it correctly and you have to prep car
@dshmechanic9 жыл бұрын
***** Amen to that! Removing aluminum parts while hot is akin to opening Pandora's box...It's just asking for trouble. Any internal stresses held prisoner by the fasteners will be given free reign to 'stretch out their muscles'. Put an aluminum piston on a baking sheet and put it in the oven and watch what happens. Out of the confines of cylinder bore, it will distort in directions it was never allowed to before. Probably won't be visible to the naked eye (but sometimes is!) so mic/dial it before, and then after it cools...you won't believe how different your 'after' readings differ from the 'before' readings.
@TheAssassin1119 жыл бұрын
I hope he brought a machine shop with him to resurface the head with...
@Revo9009 жыл бұрын
TheAssassin111 probably why he knows how to change it so well, this definitely isn't his first one.
@TheAssassin1119 жыл бұрын
R Fox You would be stupid not to resurface the head if the gasket blew... And from the looks of it, it blew due to heat hence the steam/smoke. If it was a compression blow, then probably not.
@feki1229 жыл бұрын
R Fox I hope you know he's just fucking with ya.
@hmtiller9 жыл бұрын
R Fox Was calling someone a dildo really that necessary though? Obviously you have a strong dislike of them. Maybe cause it's the only way your girlfriend can get off.
@TheAssassin1119 жыл бұрын
***** Thanx, Brah.
@Trashpanda232 жыл бұрын
11 years later, I’m still watching telling people how dope this kid is lmao!!
@KP16OO Жыл бұрын
nobody can say he isn’t a gear head now🤣 HE HOLDS THE TITLE
@PastYears8 жыл бұрын
legend says he's still in the parking lot changing his head gasket. 😂
@billybohanno72818 жыл бұрын
i can confirm that i drove past there today and he is still trying to get it right
@PastYears8 жыл бұрын
+Billy Bohanno lol
@KINGKING-pm3dm7 жыл бұрын
seen him and gave him a beer xD
@haydenspedar86886 жыл бұрын
Legend says you're stealing comments to this day
@Newrangetank6 жыл бұрын
Legend says this comment was posted over a year before yours
@retroman30759 жыл бұрын
Shocking, a Honda with a blown head gasket
@urmomsahoe18 жыл бұрын
+Retroman Porbably running too much boost from that v-tec, yo
@9909668 жыл бұрын
+Drcool52 Not trying to be a dick or anything, but V-tec doesn't produce boost.
@urmomsahoe18 жыл бұрын
red7493 I know...thats the joke.
@supersonictoast28228 жыл бұрын
+Drcool52 nah bro he let his gasket fluid get low then his header bearing went out on his vtec and fuckled the whole project
@urmomsahoe18 жыл бұрын
KSI SubSonic Yeah, I was thinking the same thing.
@marufali62056 жыл бұрын
awsome job mate there are a handful of man left in this world that can work on there own rig
@ryans4135 жыл бұрын
I like how everyone comes out and they all just stand there instead of helping him.