Bandit 2550 Stump Grinder Parker Hydraulic Cutter Wheel Motor Seal Repair

No video

Bandit 2550 Stump Grinder Parker Hydraulic Cutter Wheel Motor Seal Repair

Рет қаралды 4,764

Күн бұрын

Part 2 of the Bandit 2550 Parker cutter wheel hydraulic motor oil seal repair and what to look out for in the repair ( Note remember all the seals in the hydraulic motor are Metric )

Пікірлер: 32

@jamesdupin737 2 жыл бұрын

Awesome info. I just bought a 2900tk. I just received it and it has this same leak. Thanks so much. Great advice!! God Bless you as well!! Absolutely helped my mind. I haven’t even gone to my first stump yet 🤦🏼‍♂️.

@mustangrebuilder 2 жыл бұрын

Good luck!

@oldatlantastumps9071 4 жыл бұрын

Man you rock! Thank you for taking time to post this video. Very helpful.

@mustangrebuilder 4 жыл бұрын

I am happy it helped you ...grind on LOL

@Nevz86GT 4 жыл бұрын

Nice video, how about some videos of stump grinding techniques/advise?

@chrisrennie1019 2 жыл бұрын

Thanks for all your videos, you’ve been a great help to me opening my own stump grinder business. Been at it over 2 years now here in Virginia, just bought a 2019 Bandit 2550 with the 50Hp Kohler Diesel, I just mangled it pretty bad with a bunch of metal or something out in the country pockets sheared off, cracked teeth, but worst of all now the grinder wheel is wobbling real bad and making a terrible noise. Any idea what it could be? Thanks

@mustangrebuilder 2 жыл бұрын

Go through the process of pulling the wheel like in the video it could be like what happened to my brothers is it just moved off the shaft holding collar just a bit.

@brisbanelawncoring7283 2 жыл бұрын

I’m doing it on a hydraulic pump now. When I put the final piece in the groove for the circlip is too far in I can’t make the thing go in far enough to expose the groove. Any ideas?

@mustangrebuilder 2 жыл бұрын

It hard to tell since Im not there sorry

@raulangulo6351 2 жыл бұрын

I have a barreto 30sg, and whenever I push the button to engage the cutting wheel it won’t spin, could it be the hydraulic motor connected to the disc?

@mustangrebuilder 2 жыл бұрын

Sorry my friend I have never worked on a Barreto

@fourtrax250 3 жыл бұрын

First of all thank you again for making this video. Question? When should I consider tackling this job. Right now my 2650 has a small seep at this seal location. It's very slow.

@mustangrebuilder 3 жыл бұрын

this winter when you are slowest because it will just get worst and you dont want to be down

@baldemarteran16 2 жыл бұрын

Thanks for the video! Do you know if this would be similar process to repairing one of the back side drive motors?

@mustangrebuilder 2 жыл бұрын

Not sure

@brandonflakezzz1685 3 күн бұрын

Hey do you happen to have the part number for the o ring and seal? Thank you!! Mine just started leaking today.. terrible way to end the week 😕

@mustangrebuilder 3 күн бұрын

I order mine from a local seal supplier in my town, but call this place and have your serial number to your machine and you want the cutter wheel motor seal kit modernequipmentparts.com/bandit-parts/?gad_source=1&gclid=CjwKCAjw5qC2BhB8EiwAvqa41hy0OaatwK_Bn339HrHLllps-UKp8mtKIFaGo8cMem09M4xW6nq8NxoC-SAQAvD_BwE

@nelesstumpgrinding 2 ай бұрын

What's size of the seals on the hydraulic motor? Thank you.

@mustangrebuilder 2 ай бұрын

metric I will try to look it up this weekend

@mustangrebuilder 2 ай бұрын

do you have a seal shop near you?

@nelesstumpgrinding 2 ай бұрын

@@mustangrebuilder there's couple good bearing/ hydraulic seal shops locally available. As well as online. I figure I'd order parts on not in stock before I disassemble machine. Thanks for videos!

@nelesstumpgrinding 2 ай бұрын

Did you by any chance have time to find out seal sizes. Thank you.

@chrislavallee7902 Жыл бұрын

I'm having a hell of a time removing the cutting wheel hub from the shaft. Any insight on removing it? The book says use 4 bolts @15 foot lbs in a cross pattern. I can't get it to budge.

@mustangrebuilder Жыл бұрын

Ok so you got all the bolts off the cutter wheel right and then the star looking bolts on the cutter wheel right ?

@mustangrebuilder Жыл бұрын

kzfaq.info/get/bejne/l8-FmdmD1NSscWg.html

@mustangrebuilder Жыл бұрын

WD40 and cross hatch pattern on bolts and slit tapping on it or light heat ( light ) the collar has some rust on it

@kevincrowe2404 Жыл бұрын

I have a 2011 2250 grinder, we've found it's underpowered recently. We had to replace the clutch cable and seems to still underpowered. I did notice the hydro tank discoulerd, heats up pretty good, have you seen any issues similar to ours. Wondering if there's a leak or glossed filter somewhere. Any info would be greatly appreciated. Thanks

@mustangrebuilder Жыл бұрын

Has to be a hydraulic filter and need to be changed ... look in owners manual in the exploded parts pictures ... change fluid AW46 ..there should be a cooler for the hydraulics and make sure fan runs . I used to have that machine as just a back up and it just didn't have any balls and I think it got discontinued and they went to the SG40 .... my advice fix it and sell and get the sg40