NEW DeWALT Tools 12V MAX XTREME SCREWDRIVER (Watch Before You Buy!)

  Рет қаралды 151,997

VCG Construction

VCG Construction

Күн бұрын

NEW DeWALT Tools 12V MAX XTREME SCREWDRIVER (Watch Before You Buy!)
DeWALT was kind enough to send us over some of their newest 12V Max XTREME tools. Unboxing the new DeWALT 12V Max Xtreme screwdriver, we tell you all the information you need to know before you buy this tool! Make sure to let us know your thoughts on these new DeWALT 12V Max Xtreme line of tools in the comments section below!

Пікірлер: 296
@802Garage
@802Garage 5 жыл бұрын
Damn I love those DeWalt quick insert collets. The spring loaded action to eject the attachment is beautiful too. Pisses me off every time I pick up my M12 tools and they don't have it!
@hardnock-theoriginal..6539
@hardnock-theoriginal..6539 4 жыл бұрын
Agreed, I used to have the M12 Fuel Screwdriver which had the one handed mechanism.. until someone stole everything out of my van. When I rebought the a new unit, it didn't have the one handed eject OR the insert (w/o pull up on collet) . Needless to say it went straight back to the store. I was bummed, but I may pickup this unit and check it out.
@nakaimurray786
@nakaimurray786 4 жыл бұрын
Well as long as you can see XL call 862-955-9920me
@TheAmazingSimondo
@TheAmazingSimondo 5 жыл бұрын
Hey guys at VCG, love your videos but you have this all wrong, the settings are for torque, not speed screwdrivers are designed as an opposite to impacts. Impacts are to drive large screws through tough materials. Screwdrivers use torque settings to avoid damaging the work, like a plastic back box and are far superior to impacts when using wall plugs or narrower screws (aka almost every job in the home)
@charlesmcclure8499
@charlesmcclure8499 4 жыл бұрын
I am an aircraft mechanic. I use this screw driver on a daily basis. I love it!
@cwell2112
@cwell2112 4 жыл бұрын
These guys don't understand the tool. It's not for driving screws into wood, and the 15 settings are not speeds. It's an adjustable clutch so that you can run screws down into more delicate materials without overtorquing. It's a higher finesse, more finely adjustable driver that complements an impact driver.
@agentorange8530
@agentorange8530 4 жыл бұрын
Well they did say it's not for what they were doing.
@e.rivera4251
@e.rivera4251 4 жыл бұрын
It is intended for assembly,service,electronics, etc. Alarm installers and A/C techs will love that unit.
@keith7630
@keith7630 Жыл бұрын
I’d say they fully understand the tool and its purpose.
@ifli43
@ifli43 3 жыл бұрын
A tradesman left one at my house. Before he came back I used it. It takes all the 1/4 bits I have for my XR20v so used it on a screw clamp, then with my pivoting bit holder to drive shelf securing screws against a wall, relaced a door hinge with a self-closing hinge, and hung a few wire storage shelves. I was sold so bought my own. Check for deals. Found mine with 2 batteries for around $100. Great screwdriver and guess what, the 20v charger charges this little beauty. I have loads of light switches and outlets to replace and this is just the job on the low settings. So far so good.
@OttoTheWeim
@OttoTheWeim 5 жыл бұрын
I have the Hilti SFD 2-A and love it for plenty of tasks that don’t require impact. The only time I use the impact tools is during some type of construction but never during a disassembly or reassembly.
@TheMacGeek
@TheMacGeek 3 жыл бұрын
I bought this 12V Max Xtreme screwdriver when it came out, and I still use it regularly. This is my go to screwdriver. Plenty powerful enough for small, medium, and some large screws. Good for drywall install because it's so lightweight. Don't be fooled by the people saying 12V is not strong, this tool is plenty strong, and I've never come across a time where I thought I needed more power from the tool. 12V tools are perfect for cabinets, electrical, building book shelves, and 99% of other tasks.
@Bathtubcrocodile
@Bathtubcrocodile 10 ай бұрын
Yeah and slap on a 5ah 12v battery and you'll be able to drive bigger screws. Not that you would want to.... I'm buying this for "in the house" and smaller mounting work etc.
@jcb5388
@jcb5388 5 жыл бұрын
I just bought the DCK221F2 combo set from Lowes. Only kit in 150 miles from me. Big upgrade over the old 12v tools. I've had mine since 2014.
@Scottytremaine
@Scottytremaine 5 жыл бұрын
I bought the impact,as an hvac tech I really love it ! It’s light and comfortable to use and the led lights are amazing
@peteh4312
@peteh4312 5 жыл бұрын
I am also a Hvac tech and a gear head I love the Dewalt 12 volt platform. It is small and powerful enough especially when your in crawl spaces. And it crosses over to Mac tools ratchets
@cardo1111
@cardo1111 5 жыл бұрын
Love the reference to one of my all time favorite movies: Back To The Future. I was thinking of buying the Xtreme 12V 3/8" impact wrench as a small impact for auto work. Nice to see Dewalt back in the 12V tool game, with more competition among manufacturers the consumer usually wins by getting better products at a better price 👍🏽
@tolerbearALTII
@tolerbearALTII 4 жыл бұрын
Back To the Future 1. When Marty is playing on stage with Marvin's band, Marvin calls his cousin Chuck telling Chuck to listen to this new sound. Lol. I just picked one of these up for $40. It seems nice.
@AlanHernandez-cj6id
@AlanHernandez-cj6id 5 жыл бұрын
You have been really help full I'm new to the construction industry amd your videos help me to choose my tool smarter. Thanks!
@ericnegron8331
@ericnegron8331 5 жыл бұрын
Side note I will be getting one and just keep it on 15, it’s all about trigger control, honestly never found a reason to take a drill off its highest setting . I’m a contractor frame to finish and every thing in between.
@chaotatca2003
@chaotatca2003 2 жыл бұрын
Our company prefers Dewalt screwdriver much more than Milwaukee screw driver. Dewalt is very balance while holding and workign all day on repairing TV. some of our employee tried M12 before and their arm hurt so bad after a day. Balance is big deal if you work all day. Milwaukee need to work on this.
@hazmat3c
@hazmat3c 5 жыл бұрын
Hey Vince, we use these at work everyday. I use them for finesse applications especially with small screws into plastic boss connections. Sometimes the impact is overkill. Especially with newer users
@002nd2nunn
@002nd2nunn 5 жыл бұрын
All the new DeWalt 12v Extreme are available right now at my local Lowe's (Redmond, OR). They only have the kits, no bare tools. They have the impact driver / drill driver combo kit, impact driver kit, screwdriver kit, drill/driver kit and the impact wrench kit. I picked up the Impact Driver and a 3.0 AH battery. The 2.0 batterries that came with the kit also had fuel gauges which is awesome.
@johnmflores85
@johnmflores85 5 жыл бұрын
They got them at lowes in Texas too
@Rockcal11
@Rockcal11 4 жыл бұрын
I’m an electrician always have used both m12 m18 stuff but picked this up for small stuff .. now I have two of these love them
@jakedekleuver
@jakedekleuver 4 жыл бұрын
So it's finally available in Australia, the update I've been long waiting for. I've been torturing my DCF610XE for 7 years now and it's still going strong. I'm a mechanic and mechanical plumber, it's been showered with so many types of car fluids, dropped at least 30 times and never fails to amaze me that it's all intact and even the handle mouldings are still good. I bought it because it's maximum torque was 7nm. 90% of the screws holding a euro engines and cars together are torqued to 10nm which means you can screw fast to one notch of the full torque of the driver, and then a quick 1/4 turn of the tension wrench is all that's needed to accurately finish off the screws. I also find it very useful screwing metal ductwork on large A/C installs, and with the clutch, I can do delicate things like pull apart electronic modules etc. I'm going to buy this new one in a few months time, it's 0.5cm fatter and 2cm taller but it's a little lighter, brushless and 4cm shorter which is a big plus in the sort of work I do.
@guanyangxue9330
@guanyangxue9330 2 жыл бұрын
I got it at Lowes for $50 (screwdriver + 3Ah battery). This is the most satisfying powertool I've ever bought. It's basically a drill driver with an impact driver collet. At level 1 it's so perfect for repairing a computer. When you switch to level 5-10 it has proper torque to assemble a furniture. Up to level 15 you can repair hinges on a cabinet.
@Roblecop
@Roblecop 5 жыл бұрын
Pretty neat! Question though, are those Worx Screw Drivers worth it for the same applications? They seem super sub compact; and if you dont need the torque, than is this neccessary?
@thetruth5210
@thetruth5210 5 жыл бұрын
Buy one in your battery platform you’ll never regret it! I love my Bosch PS22 & Hilti SFD 2-A!
@Biaanca5036
@Biaanca5036 2 жыл бұрын
Ohh heeeeey! My twin! I have the Bosch ps21 and the Hilti sfd 2-A12 Almost the same haha
@chaumeisterlee6155
@chaumeisterlee6155 5 жыл бұрын
Vince your videos make me sleep easily at night. Watch a quarter way through and felt asleep. By the way love all your videos.
@bryanmarks4070
@bryanmarks4070 2 жыл бұрын
Does it lock when your not pulling the trigger? I work on small engines but I don’t like to disassemble with a impact. Snapon has an impact that won’t turn so I can break the screw loose by twisting the tool then hit the trigger to unscrew. Same as tightening I stop when it’s tight then twist the tool to torque to my desired setting. If that makes sense lol.
@stitch1007
@stitch1007 5 жыл бұрын
As an avid user of the DeWalt 12v drill and impact I really want one of these. I could have used it this last weekend putting a bedroom set together.
@liam.yurr357
@liam.yurr357 3 жыл бұрын
I have the milwaukee 12v screwgun and i mainly use it for repetitive tasks like if im like installing a million different outlet covers i use it really comes in handy but for taking things apart with speed i really recommend this type of tool
@J.Wick.
@J.Wick. Жыл бұрын
Most used too I own. That 601 is amazing. Power if you need it, light if not. Always comfy. I've beat the hell outta mine. Still works like the day I bought it. Works great on a gun bench.
@BigDee-ew6oi
@BigDee-ew6oi 5 жыл бұрын
Interesting..I will definitely pick one up to add to my job box. Thx fellas!
@torianowarren3684
@torianowarren3684 5 жыл бұрын
Definitely going to look into buying that I have the Bosch ps 22 pocket driver that I used for doing work especially inside my home or my mom's home.
@FrankDemasiIV
@FrankDemasiIV 3 жыл бұрын
I assemble furniture and this little thing is awesome for me, so light and easy to get into tight corners with
@pvillaluna1
@pvillaluna1 4 жыл бұрын
Thank you, buying this today because of your outstanding review!
@jeffscomp
@jeffscomp 5 жыл бұрын
I have the $59 Milwaukee one from Black Friday sales. It’s pretty nice. It’s handy for changing parts on something where there’s a lot of screws to have to take out and put back in. Don’t know if I’ll get the Walt.
@danielquintero4952
@danielquintero4952 5 жыл бұрын
I purchased this screwdriver in kit form(DCF601F2) with two batteries last week July 2nd. They had the impact wrench along with the impact driver and drill/ driver combo available for sale here at my local Lowe’s already. I also have the M12 Fuel Screwdriver 2402-22. It has quite a bit more torque than the new Dewalt Xtreme screwdriver.
@jackjkantrowitz50kantrowit12
@jackjkantrowitz50kantrowit12 5 жыл бұрын
Daniel Quintero I think that the M12 line of tools is a good tool line. It seems that Dewalt 12 volt line rerelease needs to be tested in the long term before buying it.
@timhappy7223
@timhappy7223 4 жыл бұрын
I bought my 8 year old a hart drill and impact. It was to bulky for him so I bought the DeWalt exstreme drill and impact. I've been running impacts to drive screws for so long I forgot about the screwdriver. Just bought my 8 year old the 12v exstreme screwdriver lol. He is doing the best learning with the screwdriver.
@joejoe6949
@joejoe6949 5 жыл бұрын
I used the old dewalt 12 volt for like 6 years.
@VRCM_Skywarn_XUSA
@VRCM_Skywarn_XUSA 3 жыл бұрын
I'm hooked on this new 12v lineup. I got the saw today too...and another lite.
@caps741
@caps741 5 жыл бұрын
Can the VCG crew do a short video on the differences between the m18 and m18 fuel? I love the performance I get from Ryobi for my lawn tools and airstrike nailers. Other power tools like drivers, hammer drill, etc. I feel like I'd be cheating myself if I didn't spend the extra bucks and get Milwaukee. I'm just not sure on the differences between the normal m18 and the fuel version. Keep up the great videos.
@6.4DieselDoctor
@6.4DieselDoctor 5 жыл бұрын
Yep guess I’ll be buying one since I’m already invested in Mac/dewalt anyway. Thanks guys
@VCGConstruction
@VCGConstruction 5 жыл бұрын
👍🏻
@number6990
@number6990 4 жыл бұрын
What’s the biggest difference between the 12v driver & the 12v drill besides the 1/4” bit holder vs the adjustable chuck?
@oreogonzalez8123
@oreogonzalez8123 5 жыл бұрын
I like the longer videos which include the tool info tool unboxing plus some tool review such as some basic tests until you do a TTR that covers more
@toolhead147
@toolhead147 5 жыл бұрын
Its nice if you have to drive a lot of screws or if you want the wife and kids to use it. I rather pull out my 18v or 20v impact driver
@kyleb4151
@kyleb4151 3 жыл бұрын
I love mine - got it for tech work, and the occasional light duty job. It's a niche, but it fills it well.
@kennethfeld6639
@kennethfeld6639 Жыл бұрын
I use this for pocket hole screws almost exclusively - setting between 5 and 9 depending on the screw length.
@K1200R
@K1200R 4 жыл бұрын
One of my favorite Back to the Future lines!
@NODTHEROD
@NODTHEROD 4 жыл бұрын
The older 12v screwdriver hex would fall apart after month of daily use but I love it when it wasn't broken. Drove a ton of 1 1/4. Better then holding a 20 volt heavy drill all day long. CANT WAIT for it to hit the market in canada (any idea when? ). Btw I love your guys videos
@vicv9503
@vicv9503 5 жыл бұрын
Thank you for making the video!! i bought mine 2 days ago. happy with it. the kit is a bit expensive for a 12v system but it includes 2 batteries(samsung INR18650-20R based, i opened one lol) it is not bad. small,light,ergonomic,perfect for a tech like me. thanks VCG(and yeah you too dewalt)!
@dw7246
@dw7246 5 жыл бұрын
Tried it vs xtreme impact and it’s faster in driving 3” screw down in 2x4 👍
@mattnixon7728
@mattnixon7728 2 жыл бұрын
I have the drill and impact driver in 12v extreme. Use em every day. Love em. Also have the circ saw, and saws all. All perform very well. Recommend em. Use larger A H batteries though
@LADYGURRLL
@LADYGURRLL 4 жыл бұрын
Just bought it right before watching. I use for 1" fine thread into pine with precise plugged holes. Also own makita 12volt fd10r1 and dewalt dcf610 and the dewalt quick release system is far superior for triple driver work. 1 for recessed hole 1 for pilot bit 1 for screw. Haven't tried Hilti new 12volt screwdriver but also interested. Maybe you could review the new Hilti 12 volt screw and impact drivers. First Dewalt Dcf610 is still going with original batteries for 4 years of daily use.
@Holiday48000
@Holiday48000 5 жыл бұрын
I have the Milwaukee M12 series (brushed) Drill, Impact & Screwdriver. I use them 80% of the time and I use them most every day. I am thinking of upgrading to either the New Brushless Milwaukee or maybe the Dewalt 12 V Atomic Series.... What would you do?
@fishingformikeytv9200
@fishingformikeytv9200 5 жыл бұрын
Love the videos watch all of them (from Japan)
@jesseganzel366
@jesseganzel366 5 жыл бұрын
I'd love one of these, but Milwaukee is breaking my arm with that m12 surge... not sure if I want to get into 2 12v lines haha
@mecniereba
@mecniereba 2 жыл бұрын
Guys, thank you for video. I was kind of shocked then I read how small is a maximum torque of this screwdriver... On UK site it is rated as 8N*m which is 70 Inch*lbs... tiny bosch go2 is about 5N*m... 12v drill drivers usually rated 275 inch lb is it really so weak? or am i missing something?
@CytoplasmicGoo
@CytoplasmicGoo 3 жыл бұрын
I used to use the older version of this when doing electrical work installing boxes, outlets/switches and cable clamps. I get snickers from other guys commenting on my "small" drill. But, its light and does the job especially when your toolbelt is already filled with hand tools for electrical work. Oh, the settings is for torque so you don't strip or break the screw and its very handy when fastening small screws into weak "wood" like IKEA furniture. I've since upgraded to the xtreme 12v impact driver which does the same thing in my opinion but with the ability to drive larger fasteners.
@matsudakodo
@matsudakodo 2 жыл бұрын
Do you still have fine control for say, IKEA furniture, with the impact?
@CytoplasmicGoo
@CytoplasmicGoo 2 жыл бұрын
@@matsudakodo yep, I just recently assembled and installed a massive ikea wall unit using this driver.
@jackjkantrowitz50kantrowit12
@jackjkantrowitz50kantrowit12 5 жыл бұрын
I like the shorter format. I think that I will take a wait and see attitude to the 12 volt Dewalt line. I have been happy with the Milwaukee 12 volt tools so far and they have proved dependable. Will Dewalt tools be as dependable for the long term use?
@puddleduckist
@puddleduckist 2 жыл бұрын
Gotta love it back 2 the future!!!! Just ordered the screwdriver kit, great review!
@rickydeathtower
@rickydeathtower Жыл бұрын
Is there any reason I should at all consider going Hercules 12v over this? Only reason I’m thinking about it at all is as a homeowner future tool purchases will be much more reasonable plus replacing a $40 piece of kit seems hard to pass up.
@cyberkiller83
@cyberkiller83 2 жыл бұрын
I use this DCF601 on my motorcycle to remove almost everything. And i LOVE the clutch, it makes sure i wont strip any threads, my engine is aluminum, so i need to be v ery careful with the threads, so this is the perfect tool. Right now i am on the market for the DCF901B that i think will have more than enough punch to remove and install heavier things like the clutch boss not, and the sprocket nuts. I can't wait to have it, i am addicted to tools! jajajaja
@dennisnunez461
@dennisnunez461 5 жыл бұрын
I thing the dewalt 12volt, is so great for me, igual have it the screwdriver the the first gen. How many the New combo brushless 12volt impact and drill driver?
@tacsystems5621
@tacsystems5621 5 жыл бұрын
I see a dewalt Milwaukee screwdriver showdown coming.
@saadlaouaouda2071
@saadlaouaouda2071 3 жыл бұрын
Will this be good to install hinges on glass shower doors?
@texaselevated7160
@texaselevated7160 4 жыл бұрын
I watched your videos and purchased the Xtreme Drill, Impact Driver, and the 3/8 impact because they came with the tstak cases. I wasn’t sure if I would like them, but it didn’t take long to fall in love with them! I’m going to order the Xtreme screwdriver just because, but I thought they were bringing out the Xreme multi also? Whatever, but DeWALT has to make a 12v Xtreme 5/8” SDS like soon! Are y’all going to be the first to have the Flexvolt 700 Pipe Threader? Can’t wait to get it in my hands 🖐 🤚 it looks DeWALT Tough!
@rcolinares68
@rcolinares68 4 жыл бұрын
Vince, is this tool compatible with a non-extreme 12v battery?
@markelkins6087
@markelkins6087 4 жыл бұрын
Hay guys . I got the 12 volt last week. Love it you no I’m not building a house so it’s great. For me retired shop in the garage guy . 2 batteries charger drill and bag 1hun.2 dollar halla
@8bitsamurai6
@8bitsamurai6 2 жыл бұрын
Just tested out the m12 impact and I want to love it cuz well made and got a great price but few things that just can't leave my dewalt for. The grip is far better on the dewalt 12v and prefer the smaller sized slide on batteries. But the biggest let down is the lack of quick release on the milwaukee. Every impact should have quick release even my old brushed 12v dewalt has it.
@ringojsp.sanchex6953
@ringojsp.sanchex6953 2 жыл бұрын
That I saw ur review Im impressed I want to get it today before Lowe's specials expires tomorrow I start a new job installing cubicle,office, furniture, and white boards Will serve me well for the Job i need for or should I get an 18v or 20v I asked home Depot for advice they couldn't answer any of questions or help me out on buy the right tool for the Job
@doctordoom1337
@doctordoom1337 5 жыл бұрын
Seems like the ideal tool for a drywall installer
@Igor-q3f
@Igor-q3f 2 жыл бұрын
Can the dewalt 5 in 1 be used as a screwdriver?
@stephenleepmg113
@stephenleepmg113 5 жыл бұрын
Hello Vince,. This Dewalt offer I think would be a great DYI guy tool or maybe a cable installation guy. In my opnion the Bosch 12V is awesome, the Milwaukee 12V is dynamite, and of course the Fein 12V is super cool, all of which I own and use. In short I think there are better choices for general contractors and speciality contractors. Cool video, thank you sir.
@chadivester2242
@chadivester2242 5 жыл бұрын
I don’t know if y’all noticed but it might be 1.5 pounds with out the belt clip but I don’t know if it is that much of a diffrence
@ajfam871
@ajfam871 3 жыл бұрын
I live these 12v Dewalts. Especially if you don’t need the power. They are much light and more compact. I have my own window and glass business. My guys always race to get my 12v pair. We will be converting to all of these 12 volts. I like that they use the same charger as the 20 volts. I just ordered ine of these. I think that the M12 line is much more developed and has more options. Huy the Dewalt has a more traditional grid and battery system and uses the same larger charger. Is they develop more options for the line it’s a homerun. We also use Ryobi for our nail guns, saws, lights, multi tool, and battery chip saw. We love Ryobi for their value and allows us to get more tool. My jobs don’t care that Ryobi is considered a cheaper tool or brand as long as they get done. And if the person using the tool is more important than the tool.
@pappaclutch3266
@pappaclutch3266 4 жыл бұрын
I wish I bought this and not my 8v gyro dewalt.. I love the tool have no problems but this one has to be a better tool. They just didn’t have it back then
@groot7133
@groot7133 4 жыл бұрын
very important to use the correct size PH bit, when they do fit correctly the wont slip, fall off or wobble at all
@heckeepagan2670
@heckeepagan2670 5 жыл бұрын
THE DE THE WALT ! These look attractive.😁😁 Bring on the hammer drill. For small applications.
@tjbrower
@tjbrower 4 жыл бұрын
Lowe’s is selling this now, just picked it up. For $99, 2 batteries, a charger, and a bag I thought it was a decent price
@Skwish6952
@Skwish6952 4 жыл бұрын
I really want this set but there is just no tools in the 12v dewalt platform.
@satchmodog2
@satchmodog2 2 жыл бұрын
I install a lot of Marvin winders and doors and I have to say these screwdriver guns are ideal. I personally bought the Milwaukee 12v, but brand doesn't matter. If you're doing fine installs, get a screwdriver gun.
@catlady8324
@catlady8324 5 жыл бұрын
I started watching but got distracted by “suggested video” of the Milwaukee Lady showing off the new Milwaukee Packout Radio! 😻
@VCGConstruction
@VCGConstruction 5 жыл бұрын
🤣🤣
@jasonlevesque9303
@jasonlevesque9303 4 жыл бұрын
Vince you forgot 1 important thing about the 12v Xtreme brushless impact driver & screwdriver. 👍 they both except and hold a 1 inch driver bit in the quarter inch chuck. And that's what really makes them more compact and fit into tight places. 👍
@VCGConstruction
@VCGConstruction 4 жыл бұрын
Whoa, gotta check that out!
@jasonlevesque9303
@jasonlevesque9303 4 жыл бұрын
@@VCGConstruction yes most other impacts the bits get stuck. But not those Xtreme ones 👍.
@TheChico868
@TheChico868 2 жыл бұрын
What the max length of screw this can drive in without stalling?
@aaronmaynard2089
@aaronmaynard2089 4 жыл бұрын
I have the Milwaukee screwdriver been using it for years my number one drill in my toolbox.
@oserratos
@oserratos 3 жыл бұрын
Just got me a fuel 1/4 screwdriver and love it as well! 👌🏽
@JF-qc6po
@JF-qc6po 4 жыл бұрын
How's the chuck wobble though?
@jaysonrae7515
@jaysonrae7515 3 жыл бұрын
Does anyone know of dewalt is expanding this line soon? I am dying to get my hands on an oscillator!!!
@lcook0825
@lcook0825 3 жыл бұрын
I would buy the screwdriver but not in retirement budget. I love DeWalt tools.
@AntonioClaudioMichael
@AntonioClaudioMichael 5 жыл бұрын
Like the led light ring
@jjirish81
@jjirish81 4 жыл бұрын
Ever since I put the carbon fiber shaman in my pocket I can't seem to use anything else, s90v keeps a mean edge for a lonnnng time lollol as for the dewalt im currently debating this or the bosch pocket driver/impact combo for the same price 🤔
@AntonioClaudioMichael
@AntonioClaudioMichael 5 жыл бұрын
I would love to do tool testing on this screw driver
@mjmjersey
@mjmjersey 6 ай бұрын
If I was screwing in switches and Outlets all day long would this be better or would I be better off with impact
@VCGConstruction
@VCGConstruction 6 ай бұрын
If your work includes adding plate covers then I’d use this for switches and outlets all day.
@rememberussliberty1822
@rememberussliberty1822 4 жыл бұрын
Now they just need to catch up to M12 line
@muddybadgers5205
@muddybadgers5205 5 жыл бұрын
I've never used a screw driver. Is the quick change collet the only benefit this has over a regular drill? I'm sure someone uses them but I've never understood why they exist
@VCGConstruction
@VCGConstruction 5 жыл бұрын
Yup pretty much the collet is the advantage
@thetruth5210
@thetruth5210 5 жыл бұрын
There is the weight savings, on a 12V tool you’re trimming off about 25% of the weight if you get rid of the chuck, you’re also not going to mar finishes on cabinets whether they be for AV equipment, kitchen or bathroom cabinet, go watch any maker channel on KZfaq and whenever they got a fit a screw in a corner you can watch their chuck dig into their project, it’s even worse if it’s a metal chuck. You don’t have that problem with a 1/4” collet. In November 2014 when I got my 12 V tools I thought the same way. I watch the video by the ultimate handyman about his screwdriver (a M12) in that following April, and how awesome it was, and I must have watched it three times before ordering my Bosch PS21 (from Amazon) I bought it on a whim believing that I would never use it and it was a gimmick, it is now the most used tool that I’ve ever owned (and bought the EC brushless PS22 as soon as it came out), would not be without it.
@lylewaters6161
@lylewaters6161 5 жыл бұрын
I would say that the main advantage of a “screw gun” is the clutch and not the 1/4” collet. You can buy a good collet that fits on any drill. I personally like the ones from Wera. I have the old version of this and use it extensively to drive screws, but I don’t treat it like it is the end all be all of screwdrivers. I use this if I’m installing equipment in an equipment rack, or installing screws on equipment. I can adjust the clutch so I don’t over tighten the screws. On the other hand, if you’re driving screws into wood, you’re probably better off using an impact driver. I will certainly buy this tool because I loved the size and weight of my original Dewalt 12v screwdriver.
@GNU_Linux_for_good
@GNU_Linux_for_good 4 жыл бұрын
02:33 Of course they did send it to you - you're the best when it comes to impact drivers and stuff like that. Cheers..
@AntonioClaudioMichael
@AntonioClaudioMichael 5 жыл бұрын
Great video Vince
@waynehenson1094
@waynehenson1094 4 жыл бұрын
Dewalt is nice. I have Dewalt and Milwaukee impact drivers, both 18v. Nice video.
@InsuranceIsLegalizedRobbery
@InsuranceIsLegalizedRobbery 4 жыл бұрын
I love battery operated screwdrivers ( of course not all ) but the ones with torque setting, I have; •HitachiDB 10DL (10.8V) this runs on 12V battery too, which is considered the same battery from hitachi ! I’m really in love with this tool, & it’s VERY expensive one, no dissatisfaction at all •DEKO DCS3.6DU2 Screwdriver (I personally recommend it) this tool has F U L L OPTIONS!! 15+ 1 Torque the 16th is Drilling mode, LED light to illuminate work space, ANOTHER LED Light at the bottom for general lighting, green.yellow.red battery indicator lights, 2 finger trigger, the tool rotates/adjusts from gun grip to straight tool, also cushioned grip for comfort! Has 200 Rpm motor from eBay for only 16.99 My 2nd favorite screwdriver •Black&Decker “SMART DRIVER LI4000 Type1 3.6Volts (180 Rpm) yes not fast BUT it’s just awesome & very well built, check it out, and thank me later
@chadharris1017
@chadharris1017 4 жыл бұрын
This tool is great for putting up metal roofs or siding. Drills are a pain in the ass and impacts strip the paint off of the fasteners. Use them daily.
@rickywangham
@rickywangham 4 жыл бұрын
makita df032dz vs dwealt DF032DWYE. Sir would like to see these above comparison
@donelias1981
@donelias1981 5 жыл бұрын
I love my Fuel Screw Driver, it's essentially a drill without the chuck. Thought I was going to hate it and didn't understand the use, but it is one of my most used tools, especially when doing electrical work such as outlets and switches.
@pnp522
@pnp522 5 жыл бұрын
After switching out 16 outlets I agree.
@dantheman9395
@dantheman9395 5 жыл бұрын
Back to the Future (the first one) James thank you for your insight Congrats on the 103k I need something with a bit more UMPH
@VCGConstruction
@VCGConstruction 5 жыл бұрын
Thanks Dan the Man Solderholm!!
@1111ALM
@1111ALM 3 жыл бұрын
and that’s how it’s done...nice review
@rudeman1914
@rudeman1914 4 жыл бұрын
Cordless Milwaukee m12 and Dewalt 12v xtreme Screwdriver is excellent for assembling Ikea furnitures.
@VCGConstruction
@VCGConstruction 4 жыл бұрын
Sure, I can see that!
@rickc.4294
@rickc.4294 3 жыл бұрын
You guys arent ready for these tools huh? Well your kids are gonna love ‘em.
The Little DeWalt that Can - DeWalt 5 in 1 Drill Driver
12:13
Tinker With Tools
Рет қаралды 25 М.
Dewalt's 12v Xtreme impact driver is no joke!
9:51
Hammer and Home
Рет қаралды 27 М.
No empty
00:35
Mamasoboliha
Рет қаралды 10 МЛН
Задержи дыхание дольше всех!
00:42
Аришнев
Рет қаралды 3,8 МЛН
The Perfect DIY Tool (12v ScrewDrivers)
14:09
Man Caver Tools
Рет қаралды 28 М.
You Should Buy 12V Instead of 20V… HERE’S WHY!
23:43
Pro Tool Reviews
Рет қаралды 377 М.
DeWalt Xtreme Sub-Compact 12v Brushless Drill Review
17:01
Catus Maximus
Рет қаралды 98 М.
When To Use an Impact Driver VS Drill: The ULTIMATE Guide
13:28
LRN2DIY
Рет қаралды 2,5 МЛН
Can You Believe This? DeWalt XTREME 12V DCS512B Circular Saw Review
21:49
Shop Tool Reviews
Рет қаралды 32 М.
NEW DeWALT TOOLS 12V XTREME COMBO KIT THAT YOU NEED TO SEE!
26:14
VCG Construction
Рет қаралды 80 М.
NEW!! Dewalt 12v 5ah Battery  (Extreme)
11:03
Man Caver Tools
Рет қаралды 36 М.
Света квадробер в парке! Часть 4 #shorts
0:31
Настя AmyMyr
Рет қаралды 1,1 МЛН
Jason made a fun pool in the Truck
0:21
Jason Vlogs
Рет қаралды 29 МЛН
BYD U8 танковый разворот
1:00
YOUR NEW AUTO
Рет қаралды 3 МЛН
СУШИ ИЗ АРБУЗА//ПРОВЕРКА РЕЦЕПТА
0:24
ОЛЯ ПЕРЧИК
Рет қаралды 1,4 МЛН
Best the best 2024❤️ Subscribe
0:14
Hayot Sinovlari
Рет қаралды 5 МЛН
Dad thought daughter wanted his food #shorts
0:10
The Nixon Fam
Рет қаралды 25 МЛН