New Whirlpool Washer Diagnostics.

No video

New Whirlpool Washer Diagnostics.

Рет қаралды 155,698

Күн бұрын

This video will show you a little bit about the washer diagnostic on a new whirlpool top load washer. You can run an auto test, individual comments and other things in diagnostic. I show what I use and mention little detail about it.
Enjoy!

Пікірлер: 285

@cabbie2111 Жыл бұрын

Man I owe you big time! Thank you. Was able to pump detergent into the tub to prime it. Was scratching my head buying dispenser tank and detergent flow pump. Regular quick cycles wouldn’t pump enough detergent through the line. Only out a few bucks, works like a charm. I appreciate you giving up this secret.

@denisemooneyham7032 4 ай бұрын

Thank you! Glad I found your video! My washer would start the sensing cycle and go straight into spin/drain mode. I followed your steps and did a factory reset. I just threw in a load and it seems to be working right now….fingers crossed. This machine is only 3yrs old. They don’t make them like they used to. 🫤

@pharabelowe4939 4 ай бұрын

How did he say to factory reset??

@RhapsodyOfRandom 2 жыл бұрын

Finally a video that’s actually helpful! Thank You!

@TROW-163 4 ай бұрын

Why are people saying these new washers are so bad they’re meant to be better for new washers

@sgtcote1 Жыл бұрын

After replacing the run capacitor, my washer is back up and running. Thank you for proving me the info for a quick and easy repair.

@Cyseralsj 7 ай бұрын

I hate it, I'll be sleeping in dirty bedding tonight because of this trash heap, it washes for less then a minute and "Wash Complete✨" Can I break it

@bjishername 18 күн бұрын

@Cyseralsj Did you call the appliance store where you purchased it? If not, why not? Did you contact Whirlpool? If not, why not? Has the problem been resolved? If not, why not? 🤔

@spotpet 20 күн бұрын

Thank you, thank you, thank you!!! My washer was stuck in sensor mode and I thought I was going to have to shell out a couple hundred bucks to the appliance repair person. One quick diagnostic cycle and the issue fixed itself!

@NeedForSpeed.2004 Жыл бұрын

The HMI (Human Machine Interface) is essentially your control panel. You can test things like the buttons, the display, the LEDs, etc

@kittitas18 Жыл бұрын

Just got saved from a headache...thank you

@thelouiebrand Жыл бұрын

Worst washer ever invented.

@DumboJumbo123 9 ай бұрын

agree, we have a nails salon and this thing broke down within 1 year

@rarelyright 8 ай бұрын

True!!!

@stephanielugo8985 7 ай бұрын

I agree

@bennyjallen 7 ай бұрын

Yep. Never worked right from day one

@mimicila19923 7 ай бұрын

@@bennyjallenI can’t even get mine to dispense fabric softener 😭 I have only had it for a week

@towandabarber8172 Жыл бұрын

Thank you for the advice! I fixed my problem and saved myself the headache of calling a professional to rob me today! Down the road I will need a professional maintenance check to clean the agitator, but for now I’m good!

@dominicarauza4645 Жыл бұрын

What if nothing works while running the test

@steveo104 Ай бұрын

Another great video! HMI is Human Machine Interface

@tamigriffith2667 Жыл бұрын

Thank you! I've had this for about 2 years and I had to troubleshoot a problem. I went to fault history and saw a FOE7. Easy remedy. This helped me get back to my favorite thing to do...laundry...NOT!

@creosoted77 9 ай бұрын

What did you do to resolve the F0E7 issue? We are getting that on our now. It's thinks we are trying to run a Washer Clean Cycle and says too unload the laundry. We are not running a clean cycle.. so very confused.

@gagejohnson3778 2 жыл бұрын

Thanks for the video!!! I got this same model about 3 weeks ago and I absolutely love it and now I’ll know how to troubleshoot it if anything goes wrong!! Keep up the great content!! :)

@kennysgf 2 жыл бұрын

Is the fabric dispenser auto as well as the detergent

@gagejohnson3778 2 жыл бұрын

@@kennysgf No. You have to manually add it each time you run a load. And don’t forget to turn on the fabric softener option.

@ednacasillas9720 Жыл бұрын

Is it just mine cause my doesn’t squeeze out all the water from my clothes

@CantonMasterDrummer Жыл бұрын

This is some nice bits of information, too bad my washer doesn’t initiate any of the diagnostic tests and therefor won’t drain the water in it. Lol. It just stopped mid cycle and said it’s putting in its 2 week notice.

@brianmerch3132 2 жыл бұрын

I’ve had mine not even 6 mos and it don’t want to work anymore it’s just crazy how expensive they are and to fix .

@ntabajohn9069 Жыл бұрын

Mines too

@rumsfield78 Жыл бұрын

Made in USA quality!!

@sgtcote1 Жыл бұрын

Agreed, ours lasted just over a year until we got the code today. Our old washer lasted over 15 years with zero issues.

@tuyetlantran7710 Жыл бұрын

Me too. Just few months and stop working 😢

@zepar221 Жыл бұрын

Got one 2.5 years old for free. No one would come repair it so the owners got a refund.

@luismanuelreyestoribio 2 жыл бұрын

Thank you very much bro, you helped me with a team that I also have here.

@cjacob741 Жыл бұрын

I have the same washer and just moved to a new house down the road. Now washer won’t power on at all. No buttons or codes just nothing. Outlets have power and breaker isn’t tripped

@blurbsmcgee3764 11 ай бұрын

How would you reset it or recalibrate it after you have worked on it?

@tiffanyharrington8295 Жыл бұрын

I wish that worked for mine. Nothing will make it light up. I have that same model and it just won't work. Could it be the whole control board?

@octavialang3166 Жыл бұрын

Were you able to get an answer on this issue?

@str8bomin Жыл бұрын

Out of nowhere, mine won’t turn on. Not sure how to get this issue fixed. Whirlpool won’t help. And I see this question has been asked many times, any help?

@diogenespeguero3673 Жыл бұрын

Was stressing the F out😫 had the wife down my throat till I found this video😁😁 almost bought another damn washer for Christmas till I found this video🙌🙌🙌🙌

@tamiawilliams3961 6 ай бұрын

How can I unlock the door.. this is the only video I can find with the same washer model.. I keep getting a drain clogged message but I can’t even open the washer door… please help

@kristinamercer8100 4 ай бұрын

Did you ever figure out what was going on? My washer is showing an error code F9E1. Any help is appreciated.

@familyvideos102 3 ай бұрын

F9e1 means bad drain pump

@johnnygallardo76 3 ай бұрын

You have to drain all the water out first by taking out the drain hose and lowering it into a bucket and let it drain into the water is completely gone then the door should unlock after pressing things like Spin and drain or something. Or you can do the Diagnostics in this video he showed how to unlock the door.

@mwayne84 4 күн бұрын

I replaced the lid switch with the proper one. Everything works except when I start it, it keeps sensing and the tub won’t spin and it just sits there. I ran all the diagnostics. I can even hear the motor running but it’s not engaging or something. I went and bought a new one but I still want to fix it. This is the third whirlpool and Maytag I’ve had in three years.

@OneOfDaKine82 2 жыл бұрын

Thank you for great tips. I need help with this same model. The spinning diagnostic didn’t work. Do you think I should change the synchronous motor?

@jonb6937 Жыл бұрын

We just got ours a few months ago, and just stopped working out of no where…. Hopefully this helps out

@Dan-t8y 7 сағат бұрын

Yep they’re garbage

@Cholo4l 5 ай бұрын

what could be defected ? i reset the codes and it washed fine for the last three washes but the code keeps coming back F8E1 water not detected but the water comes out just fine ! Thank you for the access into the diagnostics though it helped reset the codes !

@nicholeCPhT Ай бұрын

We are now getting the code ...can you help what was wrong with the washer

@NoCopyrightBangers Жыл бұрын

HELP- I have this washer but the power button doesnt work. It worked one day and now it doesnt power on. Is the panel bad?

@tiffanyharrington8295 Жыл бұрын

Did you figure out what was wrong with yours?

@kaylahoffman1539 2 жыл бұрын

I tried to get into receive the fault code, but no luck. Same model washer. My washer lid is locked and will not power on. Any advice?

@stephaniedaniels1944 2 жыл бұрын

Same

@kaylahoffman1539 2 жыл бұрын

Mine ended up being a bad control panel!

@GGG69 Жыл бұрын

@@kaylahoffman1539 thank you! I am experiencing a similar issue. Screen won’t power on and the lid locks

@roxyzamora420 11 ай бұрын

Mine is locked and can’t opened it🥺

@esmeraldamunoz9141 Ай бұрын

Same here how can i unlock it?

@bettysutton2913 2 ай бұрын

My mother just bought one and I am on here looking up how to use it for her instructions over the phone .

@dandiego6199 Жыл бұрын

So your video was very informative. I have a door lock code was wondering on how I can reset that?

@larryellis433 7 ай бұрын

You ever get that info ?

@kashfearless5872 2 ай бұрын

@@larryellis433me 2

@stankbaitfishing7914 2 жыл бұрын

Thanks for sharing the info.

@BeardedApplianceRepair 2 жыл бұрын

You got it!

@kennithconley7197 11 ай бұрын

Do you know how to calibrate this washer after oscillator is replaced?

@buenavida5407 2 жыл бұрын

Thanks for sharing the information

@yunaventura4065 4 күн бұрын

Mine says f5e3 but i checked the latch and everything works fine any tips

@jesseostone386 Жыл бұрын

Great video! Mine came from a ding & dent place and had no owners manual or ppwk, so it’s been a struggle to figure out. All the instructions are in Spanish. I do not speak or read Spanish. Is there a way to change it back to English?

@critterk5866 Жыл бұрын

I have the same model and I’m having troubles with it. I just tried testing some of these and nothings responding. Do you have any suggestions what might be the problem?

@concernedliberal4453 8 ай бұрын

Just never EVER buy one of these pieces of trash. It will totally ruin your LIFE!

@user-ie1sn9zt5h Ай бұрын

Thank you so much for this video!

@chuck5096 Жыл бұрын

Any chance you might know what might be causing mine to spin but not agitate. Whirlpool wtw7120

@natanaelacosta4074 8 ай бұрын

Why does my washer going to drain mode way before starting to wash I'll put clothes close lid it will sense then goes strait to drain and I'll show finish washing see if you can help me bro

@ParoDoXz 4 ай бұрын

Mine won’t even turn on , any fixes for that?

@brianvandegrift8407 Жыл бұрын

I was washing a load snd our block lost power during a cycle. It now says I need to contact service to fix it. How do I reset it without having to call someone to come fix it.

@user-wf2xo4bd4f Жыл бұрын

I own this exact washer and it works great in all cycles except in Bulky item setting. The items are soaking wet after cycle ends. It worked great for a year, now not spinning all water out, only in this cycle. Any advice?

@Whiteyda3rd 8 ай бұрын

My clients have a similar issue…. Did you get it?

@luvthemusic79 Жыл бұрын

Got any info on the matching dryer? We have one that's just about the same as yours washer dryer set & it's coding f7e1 no not sure how to fix it, but out dryer needs a heating element & we can't figure out how to open it up to find it

@AlKiMisT1111 6 ай бұрын

THANK YOU! YOU'RE MY SUPERHERO TODAY!!! 🦸🫶

@Loki_Dokie Жыл бұрын

Much thanks! Inlet valve is being screwy getting F8 E1.

@taylorwade2589 Жыл бұрын

How did you fix it

@Loki_Dokie Жыл бұрын

@@taylorwade2589 replace the valve assembly

@taylorwade2589 Жыл бұрын

@@Loki_Dokie did you order it from a website sorry I’m asking so many questions ours is doing that right now

@TJ-sf6kt Жыл бұрын

Where is the valve assembly located?

@Loki_Dokie Жыл бұрын

@@TJ-sf6kt take off the top cover, you gotta use a putty knife to pop some clips, and the part is what your hot and cold hoses attach to. Its a single closed system so you can't repair it afaik

@fmom5319 2 жыл бұрын

thank you for this video. very very helpful. do you happen to know where i can get the wiring schematics?

@spotpet 20 күн бұрын

Thanks!

@tracybrantley4936 6 ай бұрын

We purchased our washer about 7 months ago the load and go does not work. We had a repair person out and he replaced a part but it is still not working. I have removed the detergent cleaned it. Set it back to the factory reset, It will show when it is empty or full but doesn’t dispense

@precillarexach4014 Жыл бұрын

I got them on Tuesday last week so today. I had my first wash of clothes and I sure did not like the way the washer machine worked. The water was to low and did not wash my clothes right I still had my perfume on my clothes still. I went today back to the store to return them back and got my front loader. I will never change my front loader machines to a regular top load machine there are no good at all. I have seen a lot of bad comments on the top load machines.

@orochimaru3950 11 ай бұрын

This is my EXACT issue to the T. Had mine less than 48 hrs. Taking it back this Friday.

@eddieg3fromnc 2 жыл бұрын

I've seen where other washers have filters. I can't find one on this model. Getting ready to replace the pump.

@designwiz72 Жыл бұрын

Having drain problems on mine as well. That pump price, though 😒

@bredenis5 Жыл бұрын

@@designwiz72 were you ever able to get the drain pump fixed? Mine is throwing the drain pump error code and I replaced the drain pump and activated it and it’s still not draining. So frustrating!

@designwiz72 Жыл бұрын

@@bredenis5 it's not the pump. We actually got it to drain during a test cycle, but with codes flashing for the drain inlet valve now too. It's also not the valve though because it will fill up entirely too full and tell me it's not getting water. It's gotta be a sensor somewhere or the main board. I can't seem to find a part # for an inlet valve sensor...

@bredenis5 Жыл бұрын

@@designwiz72 thank you so much for replying so quickly! I’m sorry that you have to put up with that aggravation! I can’t figure out this darn thing either. I’m just now running a proper diagnostic cycle and I’m going to see if it is able to pump when it gets to that test.

@potatopirate_ 5 ай бұрын

my drum doesnt seem to move when it agitates, only the bottom piece really spins. How did you determine if it was the belt?

@danewidman2438 11 ай бұрын

I just got mine. Wouldn't start kept saying add garment, then completely stopped turning on all together idk what to do now. Any advice?

@GBobbyFergison 5 ай бұрын

Did you ever figure out why?

@dreamer10148 Жыл бұрын

I got this exact one brand new back in April of 2021 and tonight I was trying to get the whites done and all of a sufden I get an error F7E1. But when I did the diagnostics everything seemed to work perfectly fine! So what should I do here?

@uranusten9540 Жыл бұрын

I hate mine too. I got it during COVID

@B_HarTz Жыл бұрын

Lol, I just bought this set of a guy who got it during the vid….. and he said he called the warranty countless times to fix lots of things till he got fed up and bought a whole new other diff set…. Got these fixed and sold them to me and their working fine for me…. Said that parts were quickly put together that failed since whirlpool rushed them out to sell quickly since the world was scared and bought everything off the shelves lol Great for me when people went broke and sold them off for cheap, i was that buyer lol😂

@Pigzme 8 ай бұрын

I have the kenmore model of this washer & it is sensing loads for like 5 minutes and then shows "wash complete" and stops. Any idea what could be the issue?

@songofyesterday 2 жыл бұрын

Thanks. This helped me find the IP

@DarleneBelloir Жыл бұрын

F9E1 code. Pump is fine, drain is fine. Third time same problem, diagnostics did not help. Had to unhook the wires to the pump under the washer to unlock the lid! Less then a year old and have had nothing but trouble!

@jrsocal909 Жыл бұрын

Got the same code

@jrsocal909 Жыл бұрын

Few months old

@taylorwade2589 Жыл бұрын

I have that same cold right now

@taylorwade2589 Жыл бұрын

How did you unhook the wires

@kristinamercer8100 4 ай бұрын

Any updates on how this was fixed? I am experiencing the same problem.

@Redbone_Readerchick97 4 күн бұрын

What if the F1 code is on and the lid wont open?

@lovelyydazee4969 2 ай бұрын

Any tips on how to make it actually wash the clothes ?? Mines just says socking then drains an is done it don’t really wash them 😑🤦🏻‍♀️😭

@user-xr8ir9uc7b 7 ай бұрын

My machine is all mixed up!! It starts to spin then stops and fills again. I need to pause and start for it to wash properly cause sometimes is won't wash and hardly turn. Sometimes it starts spinning in a weird way that all the clothes bundles up on the agitator and I need to replace. Sooooo many issues. How can I try to calibrate it back to the initial factory settings?

@mayrasantiago8545 4 ай бұрын

The fabric softener doesn’t dispense since I got it last week any idea why

@btbusbee2399 7 ай бұрын

I have this washer and I can't get anything to happen on the LCD after touching those buttons 3 times each, its just dead. Is there something else I can do?

@zm4242 Ай бұрын

I have same washer and it works great for a while and then won’t turn on for day or two and then randomly I press the button and starts

@user-lv2eq4cf9g 9 ай бұрын

I have this same washer. It is stuck in drain without any clothing or any water in it. I have unplugged for time and plugged back in and it goes right back to it. Help!

@user-dw3bu3gy5h 8 ай бұрын

I have a wtw8120h and it just quit today mid cycle. I have unplugged it and there is power to the breaker. I can't get the diagnostic screen to come up or anything?

@levmelomed8418 Жыл бұрын

Brand new washer, on it's maiden run, during the spin, going fast and trips breaker on the main panel, then shuts off, locking the lid. Sad, very sad.... Calling Whirlpool, waiting about 45 minutes before real human answers. Scheduled warranty appointment online, waited all day, no one showed up .... that is the story.

@denisepayton8440 Жыл бұрын

I have the same washer. Washer was OFF when we had a five minute power outage. Now the washer will not turn on at all. Does anyone have any help or advice with this problem?

@vincelenalexander8984 Жыл бұрын

Unplug for a few minutes.

@ernestojaramillo2537 Жыл бұрын

I’m having the same problem it won’t turn on what can we do ??

@humanaddictions Жыл бұрын

I just replaced the lid switch assembly and now the close lid reading is gone but it won’t go past sensing mode. After about ten minutes I get the F5E3 closed lid error.. help

@uneCENT 2 жыл бұрын

Thanks for sharing. I've got this unit and when it is on a high spin at the end, it sounds like a jet engine in the house and I can make it go almost silent simply by applying some pressure with both of my hands to either side of the unit. It appears this thing is shaking so hard its flapping the aluminum body. It does this even with no clothing inside as well. Is it normal for this washer to shake itself so hard it sounds like it's about to break?

@designwiz72 Жыл бұрын

Mine did too, and beware the hose trapped inside the metal on the back of that machine will wear a hole. I took the back off and taped the hose till I could get a new one. Sounds just like a jet engine.

@uneCENT Жыл бұрын

@@designwiz72 Thanks!

@jeffhirsh8247 Жыл бұрын

@@designwiz72 which hose? The drain hose??

@designwiz72 Жыл бұрын

@@jeffhirsh8247 yes, the inner drain hose, right inside the metal back, all that ferocious spinning friction wore a hole.

@jeffhirsh8247 Жыл бұрын

@@designwiz72 do you have a pic of the hole and/or the site with the back off so I can see if it’s happening to mine ?

@paolonunziolicary 3 ай бұрын

$800 washer lasted 50 cycles. Would have been lower cost to go to a laundromat. Whirlpool ain't what ot used to be...

@sonnyvasquez9380 Жыл бұрын

Mine is making a very loud noise when it spins.....like the bearings need to be replaced and its not even 2 yrs old when i got it..

@mariahkokay 9 ай бұрын

Which belt did you have to replace? My whirlpool makes a high pitched screeching noise in the beginning.

@domenicm1555 5 ай бұрын

Did you fix this issue? I have a similar problem but don’t have a belt under mine

@Pittsburgh_Sports_365 10 ай бұрын

Mine seems to not engage m the timer and head unit seem fine but as the timer goes it senses but doesn't fill or run a cycle. WTH

@kevinmascuzzio3916 Жыл бұрын

Mine just broke down. It’s full of water and I can’t get the door open to remove the clothes. Starting to smell up the house…

@taylorwade2589 Жыл бұрын

Same here

@NeedForSpeed.2004 Жыл бұрын

If you can, go to service mode, and in the service functions, run the drain pump. And while you’re at it, there should be a function to toggle the lock. Toggle it and it should unlock. If not, I guess depending on how badly you need your clothes, maybe pry it open with a crowbar or something lol.

@pocketrocket1995 Ай бұрын

Begging anyone to answer My washer fills full force during the test but when I run a load I get a stream of water …. It errors out and will not fill . I factory reset and it didn’t fix the problem

@deseraehayes9611 Жыл бұрын

Will it show code it something is wrong after you do exicute I did the diagnostic and nothing showed but I keep getting unbalanced code in cycle no matter what I wash

@elinewland1694 3 ай бұрын

How can bypass lid lock.mine is saying close lid to start cycle

@Iangyavirus 18 күн бұрын

mine broke down withon a year and its been stuck on f6e1 error

@eileenprice6909 Жыл бұрын

Thank you.

@chelsearichards8819 Жыл бұрын

Mine won’t even get to the service screen… any advice with that?

@katrinawagoner27 11 ай бұрын

Mine was loud during spin and now won't spin at all. F3E3 error. Ideas?

@eishaquapearson886 3 ай бұрын

Thanks so much

@josephriley20 10 ай бұрын

Mine won’t come on at all outlet has power clothes stuck inside any tips please help…

@josephaustin4085 9 ай бұрын

What if it won't work at all the screen just flickers no display then goes black

@jacobhodges2357 2 ай бұрын

How do you reset the motor on that model?

@clarkorjamieplyler3357 9 ай бұрын

Agitator plate spins freely of the drum and won’t agitate- yet I hear the motor engage, trying to move the agitator? Any ideas?

@ydnar71 7 ай бұрын

Your actuator needs to be replaced based on that symptom.

@joelsmith6795 3 ай бұрын

Which model is this ?

@cristyrebelde20 Жыл бұрын

I have a question. I have this same one for iver a year and the detergent dispenser never empty. I'm pretty sure I'm not even cleaning my clothes. It has been full for a whole year.

@zepar221 Жыл бұрын

only use HE High Efficiency detergent. Run white vinegar through it in diagnostic mode and see if it pumps it out

@jennilynn1977 Жыл бұрын

Any idea what to do if power isn’t coming on the panel? Checked everything possible and it’s obvious that there is power to cord when it’s being plugged in.

@angiecapps291 Жыл бұрын

Same. This is where I am at and we NEED SCHOOL CLOTHES 💀💀

@tiffanyharrington8295 Жыл бұрын

Exactly, where I'm at! So frustrating. My kids need clothes for school.

@tiffanyharrington8295 Жыл бұрын

@@angiecapps291 Did you figure out what was wrong with yours?

@asaelsandoval2384 Жыл бұрын

So we all have the same problem 😂

@0ptimal Жыл бұрын

This is some bullshhh, what a garbage heap of planned obsolescence

@michaelbass3755 Жыл бұрын

F9E1 code. Third time and have to wait weeks for service tech each time. How can I unlock the lid?!

@nerdclan2311 Жыл бұрын

I have the same problem what did you do can you help please!

@kristinamercer8100 4 ай бұрын

Looking for help with the same issue. Any advice?

@user-lc8od3df7n Жыл бұрын

The pump is draining and won’t cut off…any ideas?

@brynndaniels-evertt531 7 ай бұрын

Same here

@Pittsburgh_Sports_365 8 ай бұрын

How do I directly test only the start switch?

@TJ-sf6kt Жыл бұрын

Any idea what to do if the washer fills very slow almost as if it’s a kink in the hose but when I undo both hoses water flows strong

@zepar221 Жыл бұрын

clogged inlet valve screens?

@alfredparise 9 ай бұрын

Same model the door lock will not engage WTW7120HW0 , close lid to start message

@maryloucurrington6420 4 күн бұрын

How do i start iy

@raptorbirdsfan2024 Жыл бұрын

That whirlpool Washer in the Video is the WTW6120HW, right?

@andrewvazquez6412 9 ай бұрын

Mine is having a problem where we start the washer and it runs and goes to 1 min and stops . What would be the problem?

@1911CockedandLocked 2 ай бұрын

Did you ever figure out the problem?

@Daniel-sr5tm 5 ай бұрын

I keep having power failure issues with this same model

@ilosappliancevideos47 2 жыл бұрын

Thank you. Your contents are great, however your narration is not in sync with what your action, and it gets confusing.

@davidweeks7401 11 ай бұрын

Does anyone know how to get it to reset after it has locked the lid and the LCD wont power on?