How to Cut a Straight Edge on Crooked Boards

No video

How to Cut a Straight Edge on Crooked Boards

Рет қаралды 3,878,619

6 жыл бұрын

ATTN: Viewers in Canada now have access to tools used in this video through Amazon.ca to get the low online prices you expect WITHOUT extra import duties, etc! Go to: www.amazon.ca/shop/nextlevelc... to find tools and supplies seen used in this video if you can't find them locally. Purchases made through these links are the same low online prices you expect but Amazon.ca pays small ad fees to Next Level Carpentry which I really appreciate... thank you!!
Learn how to cut a perfectly straight edge on crooked boards with a simple fixture and portable tablesaw. The method I teach in this video is very useful for doing framing work on remodeling projects because it allows you to salvage crooked boards for non-typical framing or furring applications and save straight boards for places where you really need them.
Need tools? Want to support Next Level Carpentry? Great!
You can do both right here... anything you buy through links here are the same low online price to you AND Amazon pays a small ad fee that helps support the Channel and I really appreciate it!:
DeWalt DW745 Jobsite Tablesaw seen in this video:
www.amazon.com/dp/B000HXT2N6/...
How Far Out Gauge:
www.amazon.com/dp/B01M7SFYJT/...
My favorite cordless drills by Makita:
www.amazon.com/dp/B01M1BYJAG/...
Snappy drill/countersink bit set with carbide tips are well worth the extra cost:
www.amazon.com/dp/B0167NA8KA/...
Snappy drill/countersink bit set Made in USA:
www.amazon.com/dp/B000XXZME8/...
Makita Cordless Saw kit:
www.amazon.com/dp/B0733PXF8H/...
Clic-Readers glasses are the BEST!
www.amazon.com/dp/B00U0BEI2U/...
3M Band Style Hearing Protector:
www.amazon.com/dp/B000LNKDEE/...
Stanley 25' tape measure:
www.amazon.com/dp/B00005QVRA/...
Crick's beautiful and functional 48" walnut & maple level:
www.amazon.com/dp/B0006HCJWY/...
Papermate Sharpwriter mechanical pencils... the ONLY ones I use!
www.amazon.com/dp/B07VFD43V3/...
Here's a link to the How Far Out Gauge review I did which is somewhat related to the content in this video:
• How Far Out Gauge Setu...
And this link shows How to Cut Super Shims using a fixture and method similar to this one:
• How to Cut Super Shims

Пікірлер: 3 600

@funnyharleyman Ай бұрын

I’ve done a few projects around the house and found lumber today to be absolute crap. I’m going to purchase my first job site table saw soon so I’ll try this method.

@NextLevelCarpentry Ай бұрын

Sad truth about a lot of fast-growth lumber sold these days. I always make every effort to buy the straightest stuff available because this would only help to get straight 2x4's out of pieces 2x6 or wider but I always have this trick up my sleeve as a backup. Best part is that I'm usually able to salvage more than a few pieces of old lumber on remodeling projects this way and avoid the high cost (and poor quality) of new lumber in the first place.

@civildiscourse2000 4 жыл бұрын

"Although it's probably not evident" that you put a lot of effort into the video production? Certainly evident to me, and deeply appreciated.

@stephenpalazzi720 2 жыл бұрын

Amen

@davidony1 2 жыл бұрын

I think it's pretty evident to most of us, the man is very pedantic and explains everything beautifully. Thank you sir for your patience and wisdom 🙏🏻.

@christophermelville3239 2 жыл бұрын

I really appreciate the focus on safety "they haven't made a board worth getting hurt for" is sage advice

@RingwelskiJacek 4 ай бұрын

His focus on safety would be more convincing if he had his riving knife installed...

@markabrice 2 ай бұрын

@@RingwelskiJacek And blade guard. Numerous times he reached right over the spinning blade to grab a workpiece--gave me the willies.

@phoenixpalazzo4089 3 жыл бұрын

The clarity of your voice, your dictation, the speed you speak and the speed you explain things make you an amazing teacher. If social media didn't exist, and we were back to cable TV alone, you'd be of the very few that could have had a long, succesful and adored television program. Your just that good of a teacher and host. Truly one of the best out here. Thank you so much for everything you do. Keep em coming!

@NextLevelCarpentry 3 жыл бұрын

Thanks for your kind words and glowing review Phoenix! Speaking of social media: since I don't do InstaGoogleTwitFace I hope you'll help spread the word to people you know who might share your sentiments? Thanks! Best, Matt

@phoenixpalazzo4089 3 жыл бұрын

@@NextLevelCarpentry I absolutely will!

@geoberry288 6 ай бұрын

Couldn't agree more ❤

@reachadi1029 4 жыл бұрын

This man is the real deal- like the dad I never had. Thank you for your good work, it's helped me immensely!

@alvinhall9116 3 жыл бұрын

Great video

@jeffbunjes3362 2 жыл бұрын

Abdolutely and im 71

@BostLabs 2 жыл бұрын

My Dad taught me several things, mostly about plumbing, wood working was a bit lacking. So I'm right there with you on your comment. :)

@wearechangecthartford 2 жыл бұрын

My dad went out to get some milk and cigs... have you seen him?

@santosdr2 Жыл бұрын

@@wearechangecthartford Yeah, He was on his way home but Then the Cia needed him to because his cover had been blown and he had to form a new identity. He didn't tell anyone not even your mother that he had been a double agent for the KGB for over 7 years before meeting her. Any ways the Cia heard he was compromised and had to nap him or else your whole family would be in jeopardy. SO He left to get that milk and cigs, but didn't come back to protect you. He loved you so much he just could not put you at risk. He had very little choice in the matter as well.

@Madmun357 5 жыл бұрын

Content like this is the reason I come to KZfaq. Thanks for teaching us.

@NextLevelCarpentry 5 жыл бұрын

You're quite welcome Alfonso... viewers like you are the reason I'm building Next Level Carpentry here! Best, Matt

@thangquocnguyenmdp 5 жыл бұрын

Oh man.... One of these days.... IF YOU don’t pay... KZfaq won’t let YOU WATCH....

@blackdaan 5 жыл бұрын

than imagine that 70% uses internet only for social media and nothing els..

@davew6751 5 жыл бұрын

It's too bad Google is shafting it's content providers making it harder for small channels to start all the while reaping the rewards of selling advertising on the freely provided content. It's time someone start a viable alternative to KZfaq and bring back the old rules.

@Chalstead777 4 жыл бұрын

@@thangquocnguyenmdp Not true, use it all the time N/C

@michaeldevlin2685 5 жыл бұрын

That my friend was exactly the type of tutorial a novice like me find so useful. Thank you.

@kennyg6482 2 жыл бұрын

I've had to straighten quite a few boards in my shop that were straight when I brought them home but bowed before I got around to using them. I have a straight piece of aluminum I screw to one edge of the board and run it through the table saw to get a straight edge on the board. Has worked for me for many years. Good video.

@tonyd1149 9 ай бұрын

Dear sir, you're an excellent teacher and craftsman. A blessing to your friends & neighbors, I'm sure. Thank you for making and posting this video.

@octavmandru9219 5 жыл бұрын

"I had to wrestle with the guy who wanted to use it as a boat keel ". Epic :)

@Squay313 3 жыл бұрын

hilarious

@williamtigner5387 3 жыл бұрын

Hey that was me! This dude kicked my butt then stole my board!

@roderickwhitehead 3 жыл бұрын

I literally laughed out loud... and that doesn't happen much in 2020.

@HornetKingOfficial 3 жыл бұрын

Such a great line!!

@northcackalacky4694 3 жыл бұрын

I make snow skis from Lowe's lumber

@manuelfelix5328 5 жыл бұрын

Thank you for showing how to straiten a board. Is people like you that take your valuable time to show others how to do things right thank you

@johnshilling2221 3 жыл бұрын

Manuel Felix, an excellent point. Most true expert's time is too valuable "to be bothered with" training novices. An awful lot of knowledge goes to the grave....

@gregthorup5679 4 жыл бұрын

This is very good rig, and very safe. I have often used a shortcut version of this that I call "field jointing": I snap a chalk line across the 2 low points of the bow, then freehand rip the chalk line in half; then flip the board and run the newly staightened edge against the fence; then flip it again and run that edge against the fence to clean up any imperfections in the first rip.

@NextLevelCarpentry 4 жыл бұрын

I Iike it Greg... thanks for adding a non-offensive comment to share another great on-the-job variation of this method for straightening otherwise too-crooked lumber! Best, Matt

@realrebelli0n 3 жыл бұрын

Sir, I'm so grateful that there are people like you! I'm sure you are an important pillar in your community. You're doing very well, keep it up and thank you.

@ToolshedGER 5 жыл бұрын

Sir, I just want to say that your videos are phenomenal. It is really a masterclass of woodworking and I enjoy learning from you. I just wanted you to know that the work and effort you put in your videos are highly appreciated and have a real life impact on people. Just imagine yourself on a stage in a arena with 100.000 students eager to learn from you - because this is what is actually happening here. Please continue with your clear instructions and your dry humor - Greetings from Germany!

@NextLevelCarpentry 5 жыл бұрын

Thanks for your comment ToolshedGER... much appreciated. I'll keep your perspective in mind while working on future videos! Hopefully not too many of those 100,000 students comes armed with rotten tomatoes if I slip up on occasion! 😁🤣😎 Best, Matt

@tchiz5603 5 жыл бұрын

"crooked as a bucket of snakes" I like that and will remember it. lol

@user-zq6pj5jo8j 4 жыл бұрын

That same term could be applied to any person in our government too....heheh

@tpniefer 4 жыл бұрын

T chiz, I thought exactly the same thing.

@martinbyrne6643 4 жыл бұрын

Crooked as the hind leg of a dog 🐕

@RobMacKendrick 4 жыл бұрын

You know, you can straighten those snakes out by screwing them to a strip of sheet goods...

@brianwadas 4 жыл бұрын

@@user-zq6pj5jo8j YOU TUBE "Academy Award" given for BEST COMMENT !!!

@gshaul67 2 жыл бұрын

I have been woodworking most of my life, but I enjoy watching your videos and learning more "tricks of the trade." Your videos are very well done, very informative and easy to understand, and even entertaining at times. Thanks for the knowledge download.

@NextLevelCarpentry 2 жыл бұрын

Thanks for sayin' George... and thanks for watching! Best, Matt

@CanesFinsNut 4 жыл бұрын

This is huge for me as a basic DIY'er who loves to work with wood. Thank you for putting this video out because it adds that all important safety aspect to my table saw use. Just discovered you and am now a huge fan

@DanielRomeros 5 жыл бұрын

Wow this is pure gold of instructions! Honestly, thank you for your valuable information! This helps so much!

@kikijr2283 5 жыл бұрын

I've taken up wood working as a hobby and watching videos like this makes me feel like in high school shop class once again. Thanks for the tips and tricks!

@NextLevelCarpentry 5 жыл бұрын

You're sure welcome Henry! Best, Matt

@pauleyman241 3 жыл бұрын

Huh ki I

@gregwarner3753 3 жыл бұрын

Last time I had to straighten a board on site I snapped a chalk line and cut it with a Skill saw. You set up is far more accurate and very well described.

@cintimcmomma 4 жыл бұрын

Never too old to learn something and I'm taking up woodworking. This video was so helpful. Love that you advocate for safety. Liked and subscribed! Thank you!

@yongyea4147 2 жыл бұрын

You will love it!

@learningthehardway6186 5 жыл бұрын

I’m glad I stumbled across this video trying to find a way to straighten some lumber. Straightforward and well narrated without a bunch of rambling or fumbling around looking for tools or whatever else. Thanks for posting.

@NextLevelCarpentry 5 жыл бұрын

Glad you like the video... and video production 'style'... not everyone is so tolerant of my lack of editing skills. Guess we have much in common since I've learned most of my carpentry 'the hard way' too! 😌😁😎 Best, Matt

@Bowbender8 3 жыл бұрын

So TRUE. This fellow stay on the subject. Varys only for the safety advice. So his video instruction is efficient and a pleasure to watch.

@greybeard9396 Жыл бұрын

Thank you for drawing attention to how dangerous twisted boards can be 🙏🏼

@NextLevelCarpentry Жыл бұрын

Twisted wood is the WORST!

@ralphlivingston894 4 жыл бұрын

I really like this video…I’m 60 years old and there’s nothing I enjoy more than learning… Thank you!

@bernardsaucier2062 3 жыл бұрын

And, you don’t go on and on, just teach what is necessary for us to learn!! Well done!!

@toxictraveller1892 5 жыл бұрын

You are great craftsman. I truly enjoy learning from your many years of practical experience. Sharing valuable knowledge to the next generations is a time honored tradition, and you Sir, do it with aplomb.

@NextLevelCarpentry 5 жыл бұрын

Non-Toxic Traveller, thanks for such a nice comment... I had to change your name from Toxic to Non-Toxic because of it! 😁 I've benefited by learning from the generation before me... just trying to pay it forward. Thanks for sending appreciation... you're most welcome to the knowledge. Best, Matt

@douglasyoung927 4 жыл бұрын

I love this method. I have dovetail clamps and a precision built sled that does the same thing. After trying this method I hardly ever get the sled down from the wall. It is a fast and reliable trick that saves time adjusting between cuts when you have more work than time. Excellent video!

@NextLevelCarpentry 4 жыл бұрын

Good to hear Douglas... glad you find this setup fast and efficient as I do. Other methods are necessary sometimes but having this as Plan A is cool, right? Best, Matt

@lloydpowell9496 3 жыл бұрын

I really appreciate this video. I have a bandsawmill and have a lot of edges to cut straight I’m 80 years old and just found out I’m not too old to learn

@95aubie Жыл бұрын

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzfaq.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

@alimaleki217 5 жыл бұрын

One trip to Home Depot will provide you with more bowed and crooked boards than you could straighten in a lifetime! Very helpful video; thanks!

@alimaleki217 5 жыл бұрын

Wow that’s terrible!

@Stevesbe 3 жыл бұрын

It doesn't matter where you go nowadays the lumber is the same. Young trees harvested a soon as they are tall enough to get 16' out of them

@jellyg.8961 3 жыл бұрын

There's no single store here where I live that sells decent straight boards. I'm seriously thinking on starting a straightening wood business. 😂

@slchang01 3 жыл бұрын

@@jellyg.8961 Yes, they do have straight boards, if you are patient enough to go thru them. The problem? Once you take them home and work on it, they start to warp or bow. Frustrated especially if you need a long one to build something out of it.

@jellyg.8961 3 жыл бұрын

@@slchang01 I'm patient buddy but no, the quality of the wood everywhere around is pathetic. Two weeks ago I went to HD for some 1"x4"x8' boards, after checking through more than 40 of them just three were not bowed and were almost straight. You can't find good lumber anymore here where I live.

@MrBrianDuga 5 жыл бұрын

I love the simplicity of this jig. A lot of good jigs out there, but projects of themselves. Thanks for sharing

@jimclark6256 3 жыл бұрын

And you can use it many times over.

@dancingbear6239 3 жыл бұрын

I have a 4’and an 8’ length of 3/4” plywood 6” wide. I used a straight bit followed by a keyhole bit with my router and made perpendicular T slots every foot in the plywood. When I want to straighten a piece of wood I place it on the appropriate jig and use hold down clamps in the T tracks. So much quicker and more efficient.

@teknanova8204 Жыл бұрын

This really helped me out! I’m starting to branch into woodworking and get away from the construction field so learning all the tips and tricks from you have been so helpful! I will say I did modify your jig for it to be suitable for woodworking and so on. I used 3” wide MDF by 8’ and used toggle clamps from Harbor Freight and screwed it down atop the MDF, and it works like a charm.

@TheChsmith 6 жыл бұрын

Thank you from a 70yo newbie, whose life work was as a welder/iron worker. I worked around construction sites many years but never cared for a TS due to an accident when I was about 11 (still have all 10, but one thumb has a scar) Long story short, I plan to build a 12x24 desert cabin for winter escape. I just completed my pine box (not that great, but I plan to bury my mistakes) Subscribing

@NextLevelCarpentry 6 жыл бұрын

Thanks for subscribing, TheChsmith. A tablesaw is capable of maiming but, with respect and care gets things done no other machine can. Pay attention, work safely and have fun building that cabin! Best, Matt

@brianralph5036 5 жыл бұрын

that's funny (pine box)

@johnbesharian9965 4 жыл бұрын

LOL! You're referring to your parents ("Sainted" though they may be) mistakes. Right, 'Smith?

@LoveZick 6 жыл бұрын

When I saw the length of the video I thought "why to use 15 minutes for a technique (didn't know your technique yet, but I thought I did) that's not that difficult to show". I'm very glad I clicked on the thumbnail to find it out! Because it's good information! Definitely going to use this method! Thank you!

@NextLevelCarpentry 6 жыл бұрын

You're welcome, LoveZick... I'm glad you clicked on the thumbnail too! In reality it ALWAYS takes much longer to 'show' than to 'do', right? You'll be glad to know this method is like that too: goes a lot quicker when you actually use it. Usually when I'm on a job where I use this once I end up using it multiple times so initial set up of the jig is even more worthwhile... Best, Matt

@bobharris3433 4 жыл бұрын

i think you do an awesome job explaining everything. I started to do some work around the home because of corona-virus and I watch plenty videos and yours are number one for me. the younger guys are very innovative but they seem at times to lack something in the videos. So far i have built a study table for my daughter, a chest of drawers and a closet with wood sliding doors using metal track on the gable slope in my 1.5 story home. So thank you

@acolon4617 2 жыл бұрын

The younger fellows want to do everything too fast and flashy without regard to safety, i.e. proper hold-downs, push sticks, DUST extraction, masks and visors or woodworking gloves. Forgive me but I like my lungs, eyes and especially, my hands without splinters and ALL fingers! 😁

@simonhunter6937 3 жыл бұрын

Hello from Scotland! I've just built my first shed which will be my wood workshop and that has coincided with me finding your channel. I'm inspired as i've ever been watching your content and ready to tackle some projects. Thanks for the clear and concise instruction!

@NextLevelCarpentry 3 жыл бұрын

Greetings Scotland! Welcome to Next Level Carpentry Simon... hope you get a chance to see newer videos here on the channel that show a lot more 'inspirational' in-depth tips and techniques for woodwork and carpentry.... Best, Matt

@jeffmiller9711 5 жыл бұрын

Excellent video. For an amateur like me this was very informative. I use a lot of salvaged lumber and repurposed wood for projects and couldn’t figure out how to get a straight edge.

@NextLevelCarpentry 5 жыл бұрын

Everybody starts somewhere, Jeff... hope this helps you out as you gain experience and ability! Best, Matt

@katharinwalker784 6 жыл бұрын

I don’t have a jointer or a planer so this technique is a Godsend! Thank you for sharing your knowledge.

@NextLevelCarpentry 6 жыл бұрын

Thanks for letting me know, Katharin, you're welcome for the knowledge. Your perception of the advantage of this technique tells me that you'll be able to use and adapt it to expand things you're able to do with limited resources which is a large part of being a productive carpenter! Best, Matt

@theholyrice 4 жыл бұрын

Best woodworking tutorial video! Love how thorough and detailed every step is explained.

@kirkinthemountains8327 4 жыл бұрын

Sir, I could watch you teach me carpentry all day long. You obviously are a master of your craft. Thank you for this video and all the others!!

@TryThinkingAboutIt 6 жыл бұрын

Excellent presentation: it focuses on content (not the presenter), is fluently delivered, well edited and thoughtfully produced.Thanks very much

@NextLevelCarpentry 6 жыл бұрын

I appreciate your comment and subscription, Ian, much appreciated. Somewhat surprising to me how most viewers agree with you but a few most definitely do not... such is the world of KZfaq, I guess? Best, Matt

@dnbr2002 4 жыл бұрын

just wanted to say thanks. I found this method here. used it on some old barn wood for a table I'm making. it worked great. I'm a real noob with a table saw and it this was fairly easy even with some pretty big old barn wood i was working with.

@rithlim6016 Жыл бұрын

The level of details you added to this video is assuring.

@calveryc1 4 жыл бұрын

Great job. I appreciate your effort and thoroughness. Your edit to use the more warped board was definitely more instructive as you could clearly see the bow in the board. Keep it up.

@MrTeff999 5 жыл бұрын

This was one of the best instructional videos I've seen. Excellent editing. I know that editing can be the most time-consuming and tedious part of making a video. I rate it a 9 out of 10. (I deducted a point because you didn't have a sexy helper.)

@NextLevelCarpentry 5 жыл бұрын

Thankful for the 9 because a 10 would mean you thought Chip was a 'sexy helper' and THAT would be a bit disturbing! 😱😂😎 Best, Matt

@captainjack8823 3 жыл бұрын

@@NextLevelCarpentry 👍, We carpenters love the ladies. The kind that aren't a carpenter's cull, "flat as a board with no curves"! Been in the trades for the better part of 40 years and men with too much sugar in the tank don't cut it!

@aldunlop4957 2 ай бұрын

What a gem of a video this is. I'm in the process of trying to make my very first "proper" woodworking bench and the top will be made up of 2X4's glued together. I feel as though this video was custom made for me as it describes my situation exactly. I was at the stage were I was getting ready to place an order for some T track and other accessories but now I dont need to! Not only has this video demonstrated that I dont need a fancy jig but it's saved me money as well. Thank you for sharing your knowledge (and saving me some cash) 👍

@placacentrocasamania 3 жыл бұрын

I think some knowledge has to be offered in each video. The method used to straighten a board that you show, permits us to learn the correct secuence of steps to eliminate the crown of boards. It can be applied, the theory in others precedures but the secuence is always the same. Thanks Gerardo

@mattperryman7491 5 жыл бұрын

Thanks, man! I've got some older lumber that has warped, and I've been trying to figure out how to salvage it. This method will work perfectly! You're video was concise, straight to the point , and easy to understand. I like that you threw in that 2nd picked over board, that REALLY drove the point home. Thanks again!

@NextLevelCarpentry 5 жыл бұрын

The more pieces you have to straighten, the more it's worth the few minutes it takes to make a jig like this Matt... work carefully with this fixture, especially at the start, since it's a bit different than just using a tablesaw by itself. Hope your salvage project goes well! Best, Matt

@daleney7211 3 жыл бұрын

well done, new retired hobby, love wood work & turning, no plane etc. just basics, but luv it, relaxing for an old soldier.

@mikeg1593 Жыл бұрын

Good job on the video. Like others, I can also learn new tricks from you. However I noticed your roller stand has what looks like a thin plywood ramp on it. I'm sure you have a video on it but I'm new to your library and wondering if you can direct me to the video you made to modify the stand. Sometimes the details are worth learning too. Thanks.

@NextLevelCarpentry Жыл бұрын

Good eye, Mike! Here's two of 5 eventual episodes telling you everything you need to know about that outfeed roller stand which, as you'll see, is called a GROAT: kzfaq.info/get/bejne/nsp4ZJuS2MvMmJ8.html kzfaq.info/get/bejne/ebinbNerr6uzeGg.html And here's a link to set of available plans if you're interested: PLANS ARE NOW AVAILABLE for GROAT Tangent Ramp Outfeed Roller Stands that are EXCLUSIVE to Next Level Carpentry on KZfaq at an introductory price of just $15... next-level-carpentry-swag-shop.creator-spring.com/listing/groat-greatest-roller-of-all?product=953 Best, Matt

@dolly280156 4 жыл бұрын

Thank you so much. I am a beginner a I finally learned how to make crooked wood straight. Please continue teaching people like me.

@fitz394 4 жыл бұрын

I love that almost 2.5 years later, he's still checking comments and not only roasted, but pinned the roast of obligatory KZfaq comment section "expert". Thanks for the tips. This and the "Supersize your joiner" video has been invaluable

@TottLy 5 жыл бұрын

Thanks Matt for an instructive video! Living on an island in the Swedish archipelago. From time to time I am sawing my own lumber with my chainsaw - from trees in our forest. Wood is certainly a living material so this trick is very useful when you don’t have a jointer. I also like your attitude re safety precautions... I am glad that I still have my fingers intact. / Best Torsten

@NextLevelCarpentry 5 жыл бұрын

Always great to see a comment from far-flung parts of the world Torsten.. thanks for yours... Work safe, have fun! Best, Matt

@locke0811 2 жыл бұрын

Working with old barn wood and I appreciate your video. Thanks very much sir.

@zacharyunger2004 4 ай бұрын

The fact that your editing and behind the scenes work *can* go unnoticed is a big mark of its quality. The sort of thing people will often only notice when it is poorly done. Great video!

@mikeashland1901 5 жыл бұрын

Simple, effective solution that gets the job done... keep these videos coming. As a 70-something self-taught re-modeler I've used jigs like these and the shimming techniques of the other video to correct some real nightmares. The TG flooring grade OSB (more dimensional stability in moist environments) straight edge can also be modified to straighten the edge of 4x6-10 lumber used around windows and doors using a good portable circular saw (i.e. Makita w/Freud Diablo). Screw stop-blocks to the underside of the guide, at the ends of the work, positioned with the saw foot against the edge and blade edge at narrowest point of the work. Then screw the guide assembly to the work. Make a first cut a little more than half way deep. Flip the work, re-attach the guide and repeat. And, it's safer than man-handling on a TS.

@NextLevelCarpentry 5 жыл бұрын

Great adaptation Mike.. thanks for sharing! Best, Matt

@Cujo_Ate_My_Credit_Card 4 жыл бұрын

Excellent pro tip! The hardware store near me sells boards that are perfect if you need to make wooden airplane propellers or rocking chair runners.

@jellyg.8961 3 жыл бұрын

🤣🤣😂😁

@craigdecker2219 3 жыл бұрын

Yes helped a great deal doing small projects with mostly scrap and bowed wood

@randmayfield5695 9 ай бұрын

I get highly discounted warped or defective lumber and take the good wood out to make jigs and saw horses plus a bunch of other things. This video helped me with making better use of defective boards. Your attention to detail in producing this instructional was amazing. Thank you! I subscribed and hit the 'likes button'. Watching this made me a better woodworker.

@trickhealey 3 жыл бұрын

I was like no way I’ll watch almost twelve minutes of how to straighten a board. I then watched almost twelve minutes of how to straighten a board. Good work.

@popparock6506 3 жыл бұрын

right! .. and I'm off to now watch the other 2 vids he suggested.

@aaroncameron1494 5 жыл бұрын

His voice is so consistent that in between cuts it sounds like a continuous sound track.

@AP-nb6og 3 жыл бұрын

Thank you for this video and for the removing sheet rock with less mess video! I am impressed with your video & editing skills, too. My 8 year old creates You Tube videos and I see how much work she puts into everything. I'm impressed you are a master carpenter AND a You Tube content creator! It is clear your intent is to educate, and I thank you for passing on your skills to a new generation.

@NextLevelCarpentry 3 жыл бұрын

Wow... thanks for this comment... especially on this video that generates so much ungrateful criticism for its choppy, less-than-perfect, video editing. Not all viewers have the perspective or lend the grace you do to see/learn the lesson despite the not ready for prime time delivery... Best, Matt

@TheGermanElectrician 4 жыл бұрын

Thumbs up. Well explained and also understandable for (small) people (my son has just turned 10 years old) who do not speak or understand English perfectly. Thank you very much for this video and tutorial. Greeting from Germany

@terrystephens1102 5 жыл бұрын

You do a really great job - both instructive and enjoyable 👏👏

@patrickallen1169 3 жыл бұрын

Thank you for this video!! I just straightened my first warped board after watching this and it worked like a charm. I appreciate the safety tips too! Happy Holidays!

@williardpienus8014 3 жыл бұрын

I wanted to thank you. I wrote over 6 months ago asking if this would help to edge joint for a table top. After much practice with scrap, I got the hang of it and was able to joint 2x10's for a nearly 4foot by 8foot table. The edges went together so perfectly that I couldn't believe it! After a glue up and having practiced all the other skills from "KZfaq" and thrift store woodworking books, I built a beautiful table, with dowelled aprons , a dovetailed tressel, and a nice dry aged finish patina... but the thanks begins here with your video, as getting those boards to join together was the biggest challenge. Now I'm ready to make another one, but this time with only hand tools and an old wooden jointer plane from eBay!! Thank so much!!! God Bless!

@NextLevelCarpentry 3 жыл бұрын

And I thought this was only for framing lumber Williard... who knew?! Feel free to link to photos of your table if you want. Thanks for watching and commenting here at Next Level Carpentry! Best, Matt

@chirone00 12 күн бұрын

This was a great video and the emphasis on safety was awesome.

@NextLevelCarpentry 6 жыл бұрын

Greetings viewers and subscribers! I mention links to two related videos at the end of this one. I'll add the links as soon as the other two videos are produced and uploaded. I hope to finish them up soon because each one relies on the other two to be most useful... sorry for the delay and any annoyance this causes. Best Regards, Matt

@remlok2655 6 жыл бұрын

Excellent, as usual.

@NextLevelCarpentry 6 жыл бұрын

Thanks rem lok, the mission of Next Level Carpentry is to supply useful content with a goal of reaching an 'excellent' rating with viewers like you... Best, Matt

@CaseAgainstFaith1 6 жыл бұрын

Just wondering if it is worth spending that amount of effort to save a 2x4. Especially when you say in the end, it might just bow again.

@NextLevelCarpentry 6 жыл бұрын

CaseAgainstFaith, To be fair I'll say that it's not always worth the effort but often it is worth salvaging random pieces of bowed wood on a remodeling project. Not only does it save unnecessary waste going to the landfill but it can save trips back to a lumberyard, a real consideration on some projects in some parts of the country/world. Mainly I hoped to show what can be done when it IS worth it more than what to do with every bowed board I encounter. Thanks for watching and commenting! Best, Matt

@CaseAgainstFaith1 6 жыл бұрын

Fair enough. And, you really did do a good presentation. Thanks.

@stevenclanton7989 4 жыл бұрын

Thank you for going the extra mile to find the piece with more warp in it.

@randyrice7214 2 жыл бұрын

I've been looking for videos that cover this process and coukdn't find anything until this video, which did a great job. Thank you!

@dhermitmorse Ай бұрын

Thank you. This was very helpful. I plan to use this method to cut some Brazilian hardwoods from my local granite countertop place. They offer their shipping woods and pallets for free but several of them are bowed like this.

@adamchou9123 6 жыл бұрын

kudos to you for taking the effort to refilm with the extra bowed board. great effort sir!

@NextLevelCarpentry 6 жыл бұрын

I appreciate the effort you took to add a comment too, Adam, brings home the point of how well this little setup works. Best, Matt

@GentlemanH 5 жыл бұрын

Yes - thank you for your effort of showing a very crooked plank. It illustrated your point much more clearly.

@cariemck805 5 жыл бұрын

Loved every minute. I learned a great (& much needed!) trick and added a few new jokes to my repertoire. Definitely going to watch more of your videos.

@NextLevelCarpentry 5 жыл бұрын

Thanks for subscribing and commenting Carie... hope you find it worth your while to browse around Next Level Carpentry! Best, Matt

@charlesmiller3114 4 жыл бұрын

Thank you for taking the time to make this video. As a beginning woodworker it is greatly appreciated.

@johnshilling2221 3 жыл бұрын

I can't say what a pleasure it is to watch videos made by true, experienced Craftsmen. There are an awful lot of videos made by people that mean well, but they teach people a lot of "hard ways" and worse, unsafe ways.

@NextLevelCarpentry 3 жыл бұрын

I wonder if you want to edit your video to change the word can't to the word can John... I think it would Express the true meaning of your comment which at present might be the opposite of your intent😁

@halfbeardsilvertongue5129 2 жыл бұрын

Thank you for this video, Sir. With the price of lumber these days your idea will, I think, help me save a lot. I bought a bunch of 2X8's to rip into two roughly 2x4's but some are slightly bowed. Had what I thought was a great idea to use an 8' 80/20 piece of aluminum to screw to one side of the lumber to create a straight edge, but the accuracy is somewhat iffy to keep from cutting too much off that first pass. I really like your method and will use it instead for now. Thanks again and keep up the great work! 🙂

@NextLevelCarpentry 2 жыл бұрын

I think the general concept of what I show in the video will be useful for ripping your 2x8's in half the long way so I'm glad you like the video. If the 2x8 is bowed in the first place you can use this method to straighten one edge by trimming just a minimal amount off to remove the bow then use that straightened edge to rip the piece in half. I'm guessing most, if not all, of the pieces straightened and ripped that way will yield 2 'roughly 2x4's' that have a bow in them because of internal stresses inherent in 2x8 framing lumber. Those would in turn need to be re-straightened and re-ripped to end up with two straight pieces. The size of the resulting two straight pieces will depend on the quality of the lumber involved and how dry it is. In some worst-case scenarios you might only end up with a couple 2x3's by the time you're finished but, once you get an efficient workflow going you might realize some savings because, as you say, lumber prices are a real factor these days. Good luck! Best, Matt

@30AndHatingIt 2 жыл бұрын

I make a lot of stuff out of pallet wood and, as you can imagine, a lot of it is in bad shape with bowing. After looking up numerous ways of remedying that, I actually got a little overwhelmed and happened to look over at my late grandfather’s 4 foot level that I inherited. Since no pallet boards are longer than 4 feet, I thought… what if I just hang the edge of it over the side of the boards, near the fence, and run it through? Sure enough, it’s a fast and easy way to get one side straight enough that you can then flip it and make the other side parallel. I found that if you do it in multiple passes, starting away from your final cut and walking it in like you’re slowly shaving it down, it gives the best result. Obviously this won’t work for 8ft 2x4’s because I don’t think they make levels that long. In this case, go with what this video shows.

@thomasdickson3622 Жыл бұрын

You can get levels up to 12 ft, but they start getting pricey. Harbor freight has 8 footers for cheapish.

@martinriesebosch.7600 Жыл бұрын

That’s what I do as well. I purchased a 12’ 4”x2” x 12’ hollow aluminum Chanel. Also have an 8’ one. I don’t fasten any thing. Just put to board against my straight and push both through along my fence. I do have a four foot long unifence on my Delta unisaw though so that helps. Works perfect. Cheers.

@helmanureygonzales917 2 жыл бұрын

Thank you very much for sharing your knowledge, a very useful advice for those who are just starting out in this trade, a Hug for you from Bolivia 🇧🇴

@NextLevelCarpentry 2 жыл бұрын

Bolivia?! How cool is that! Thanks for watching and commenting... Best, Matt

@bradchristy5002 3 жыл бұрын

Excellent point, putting the bowed portion against the guide & why. Very helpful - I didn’t get that point from other videos. Thanks again - you bet I am subscribed......

@ammer3934 6 жыл бұрын

What a great idea. All your Videos are really informative. Keep them coming. Good luck.

@NextLevelCarpentry 6 жыл бұрын

ammer, Thanks for the comment and compliment... glad you like the videos. I hope to get two more produced and published soon!

@els1f 5 жыл бұрын

Seems like a good guy. This was real helpful 👍

@treeman0878 2 жыл бұрын

40 years in a trades, I watched a different way of straightening boards 'on the job site' with great interest. Most of the time I do it by eye, and or, make repeated cuts flipping the good (2 point) edge against the fence. That said, using a straight edge, as you do here, whenever you can is preferred, more accurate and safer. Similarly, I commonly use an 80-in door casing level (that I almost always have with me) on its side and spring clamp it through it's handles on to the table saw fence. This in essence turns my table saw into an on-site jointer with 40in in-feed and out-feed tables. I always believe there is at least 10 ways to do something, anyting, thanks for your encouragement!

@daviddye1303 Ай бұрын

Clear and concise. Easily understood. Thank you for your excellent advice.

@kozkoz7776 5 жыл бұрын

Your a great instructor you can be my Boss any day I just learned something new thanks

@NextLevelCarpentry 5 жыл бұрын

Careful what you wish for Cosimo... 😉😂😎 Even if I am a pretty nice guy you're still better off working for yourself! Best, Matt

@johnbesharian9965 4 жыл бұрын

@@NextLevelCarpentry The "Joys of Ownership" cannot be replaced. Once experienced, nothing else is ever quite the same.

@teranbicicletero 5 жыл бұрын

Doing a dining table and I've seen the other videos you talked about on this video....this is way more simplified, and more affordable for my broke ass

@jhund81001 3 жыл бұрын

This video was awesome. I don't own any of the equipment, or even have a garage to work in, but it's nice to be able to learn from an expert. You got a new sub. Thank you!

@NextLevelCarpentry 3 жыл бұрын

Glad you liked the video and thank you for the sub! Who knows you just might find enough inspiration 2 get into some carpentry... definitely a useful skill set... Best, Matt

@misterlarryb Жыл бұрын

Love it! Thanks so much - excellent demo, great explanations, nice safety first. LOL - 11:19 - "But I did have to wrestle with a guy who's building a boat and wanted this for the keel!" Thanks again!

@NextLevelCarpentry Жыл бұрын

Yeah, I always have felt bad for that guy... I didn't learn his name and really hope it wasn't Noah!! 😂

@ZacJones 6 жыл бұрын

Great video! That wood is as straight as an arrow, thank you!

@NextLevelCarpentry 6 жыл бұрын

It's a slick trick, Melrose Design, hope you find it useful... it looks like you're on a journey to build a KZfaq Channel; I wish you well and appreciate the cross channel collaboration with your comment. Best, Matt

@roberttravalent7782 2 жыл бұрын

Thank you for the awesome video. I really like the detailed information you provided. I'm curious about the roller stand out feed modifications. Thank you again.

@NextLevelCarpentry 2 жыл бұрын

You're sure welcome Robert... and, regarding the outfeed roller stands; stay tuned for a full-on build video for them in early 2022... Best, Matt

@neeru7298 10 ай бұрын

The dedication of this man to repeat with a more evident board after the firsr exemple

@citadelforsomerefuge 4 жыл бұрын

Thanks from India...I saw so many videos and everyone used techniques that require clamps or complicated jig... This is the best ..I purchased offcut teak for cheaper price and wanted to straighten the edges and gonna try this . Many thanks.

@NextLevelCarpentry 4 жыл бұрын

Offcut teak? How cool is THAT?! Hope this helps! Best, Matt

@citadelforsomerefuge 4 жыл бұрын

@@NextLevelCarpentry truely truely it worked ..I tried this technique today and got nice parallel cuts . Many thanks .. now watching your other videos and finding more Gold 😀

@bravesfan1947 6 жыл бұрын

Thank you sir you present yourself and your videos very well.

@NextLevelCarpentry 6 жыл бұрын

You're welcome, Negan... I appreciate the compliment. It's my goal to 'present' well but have far less confidence in the video part than the carpentry part so it's nice to hear how things are coming across! Best, Matt

@herbieherbert912 5 жыл бұрын

Very good Video and advise for me, as I've been trying for weeks to get the best idea to straighten my wood. Thanks Herbie

@salgiuffrida554 5 жыл бұрын

Negan ! Thank

@valpanig 5 жыл бұрын

i agree with you, Matt sounds like a true professional.

@markarmstrong2592 6 жыл бұрын

Good simple jig that is also safe to use

@NextLevelCarpentry 6 жыл бұрын

Thanks Mark! I'm currently doing an extensive remodel of a Master Bath Suite and expect to use this method numerous times in the rebuilding process... hope you find it useful for work you're doing! Best, Matt

@hfzmu 3 жыл бұрын

My hats off to you sir. Your explanation is succinct and crystal clear. You've earned a new subscriber in me...

@nicknick1963 2 жыл бұрын

I spend all day working with bowed timber,this is gonna save me so much time and improve my work. Subscribed

@mixxxmaster74 6 жыл бұрын

as a beginner, this is treasure...!!!! thank you for such an educational video...

@NextLevelCarpentry 6 жыл бұрын

Glad to oblige, Akshay... you're most certainly welcome! Best, Matt

@Manofwarshs 5 жыл бұрын

Akshay Malhotra -$$++

@daveremenaric7824 5 жыл бұрын

Rv roof sealsnts

@ChileExpatFamily 6 жыл бұрын

Thanks for the video. All the wood here in Chile is crooked and green so this video helps a lot. Jim

@NextLevelCarpentry 6 жыл бұрын

Wood in Chile might be crooked and green but I'll bet there's some gorgeous boards! Hope the tip helps you, ChileExpatFamily! Best, Matt

@ChileExpatFamily 6 жыл бұрын

Next Level Carpentry you know it! Most of my lumber was cut off my own land by ME. I have a friend come with his saw mill and we make real wood. I burn, or make 4x4 fence posts out of wood you would be making furniture from. Really nice clean grain with dark red color hard wood. There is some beautiful wood here. Different from the USA. Hard. Really hard stuff. You just gotta know how to take it from tree to boards yourself. Jim

@NextLevelCarpentry 6 жыл бұрын

We should work something out: I'd love to have some of your 'firewood' to make some of the jumbo carpenters's pencils (the ones you see in my shop and videos) out of. Would it be crazy/cost a fortune to send a few chunks to South Dakota USA? If it worked I'd make a pencil for you when I make others and send it back... just brainstorming... but it sounds like an adventure project if nothing else. Best, Matt

@ChileExpatFamily 6 жыл бұрын

Well the other day I bought in Arizona some solar equipment and the seller only uses UPS. The cost was going to be $1,387 USD for a 90lb box. So here is how crazy that is... (It is stealing)..... I am going to buy an airline ticket and fly back and pick up the solar charge controllers and fly back!!!! It is cheaper and faster and easier. The best thing is for you to come visit my family and I and then pick up the wood you like and take it back with you! Or just move here.... Hahahahahah We do not have the selection you would see in the Amazon but we do have some interesting hard wood to say the least. If you go to LOWES you will find all types of Chilean base board stock and such. Pine is planted here just like it was for me in South Carolina. How far are you from Oklahoma City? My oldest son lives there in the Air Force. Jim

@NextLevelCarpentry 6 жыл бұрын

Your 'shipping and handling' scenario is remarkable but believable... plus you get to enjoy some real heat in July going from Chile to Arizona! Thanks for the 'invite'... I now have a perfectly legitimate reason to plan a vacation to Chile... next January maybe, when it's -10F here and '80's there? We must be around 1,000 miles or so from Oklahoma City... but only 20 miles from Ellsworth AFB in South Dakota. Take care, Jim! Best, Matt

@anthonytimmins8861 2 жыл бұрын

An excellent presentation, thank you from Adelaide, Australia.

@mikeklimczak1915 3 жыл бұрын

This is SO good. I'm a total beginner and have been reclaiming unused lumber from nearby home construction (I contact the foreman first!) and have been practicing milling them but thought I'd have to build some truly massive fence to be able to mill long boards. This is SO simple! Great tip with the coloured end of the machined board as a source for a straight edge. It's a like and subscribe from me!

@NextLevelCarpentry 3 жыл бұрын

Thanks for letting me know how helpful this is for you Mike. It's truly a good trick that you have up your sleeve as you continue to build your skillset and gain confidence. Best, Matt