Even though I have no hope of doing this myself in the near future, I do now have a new hobby I might be interested in. Soldering/Testing/Replacing. You seem very knowledgeable and I love that you think out loud and take the viewer with you and explain what you are doing on why it might or might not work.
@RetroTechCorner Жыл бұрын
Thanks! That's exactly the idea - I don't think heavily edited videos that don't give any clues on how to get to the solution are very helpful. I mean - they look nice, sure (certainly nicer than mine :)) but when it comes to learning or solving a problem - real life experience is always better...
@dary00975 ай бұрын
Nice walk through , This is exactly what mine is suffering from and maybe gonna try it myself since They are charging me $125 for this
@satishkarate4519Ай бұрын
Hi Guys .. I ran into a similar issue. Save yourself time and money repairing the console's Wi-Fi module by buying a simple cheap Wifi Ethernet Dongle (USB-C type) , connect using a physical ethernet cable download games, update console, backup etc .... I personally tried and tested and it works like a charm
@vemelyn554 Жыл бұрын
Could I possibly ship my switch to you overseas? I can't get the chip off, I'm terrified to breakmy switch and lose everything, and I've no options left. If you take my comment into consideration I will link contact information, thank you for your time!
@falconmick Жыл бұрын
I’ve seen other chip repairs using a solder mask and applying solder paste this way, would this approach have any benefits or is the solder + iron approach sufficient?
@baimzgaminghealth38656 ай бұрын
mine had 2100-1100 it same hardware wifi chip problem?
@bananaboy3316 Жыл бұрын
hi what chip should i use to fix wifi on oled?
@jet613 Жыл бұрын
I'm pretty sure they are interchangeable. My OLED came with the cyw chip.
@HunterplaysminecraftKove11 ай бұрын
What microscope are you using? That’s clear as day
@cr4zyw3ld3r9 ай бұрын
Came here to ask this!
@RetroTechCorner9 ай бұрын
Purchased a few years ago on aliexpress. Can't remember the brand but the most important thing it's based on Sony IMX290 sensor. Mine is autofocus but I disable autofocus anyway -it's annoying when soldering/working on electronics. Autofocus could be useful for PCB inspection though. Anyway - anything that has IMX290 should be OK. There's a lot of fakes (eg. IMX185 advertised as IMX290) so it's worth buying from trusted sellers. I've heard IMX385 is also good. BTW - it's 1080p/60fps. I don't see a point in going for 4k for soldering. I think this might be OK but again - make sure it's using genuine IMX385 sensor. www.aliexpress.com/item/1005005051033283.html
@zuppdemonz98847 ай бұрын
do you think this would work on switch lite as well? for months now and I can't connect to wifi and wasn't able to transfer my pokemon games to my new switch.
@RetroTechCorner7 ай бұрын
I don't see why it wouldn't work. But (as I mentioned in the videos) - you'd most likely need to use original Nintendo chip... EDIT: actually, on a lite you could probably use Chinese chip - if you don't need BT as lite has (obviously) hardwired joy cons... :)
@MrDinakdakan Жыл бұрын
the chip it start with cyw or bcm? 12usd one or 4usd, llooks likd cheaper one only wifi works and not bluetooth, maybe reball the original one if no cracks
@RetroTechCorner Жыл бұрын
I did recall the original one later. No luck - the chip was dead.
@hove131 Жыл бұрын
Do you reball these chips before reinstalling?
@RetroTechCorner Жыл бұрын
Yes - if you remove BGA chip then you need to reball it (and clean the pads no the motherboard)
@hove131 Жыл бұрын
@@RetroTechCorner yes I'm aware I repair consoles I just wasn't sure if you did because I've watched your videos and didn't see that process so was just curious
@yo27ju Жыл бұрын
how do you test de oscilator
@RetroTechCorner Жыл бұрын
Remove the eMMC, solder a very thin wire to one of crystal pads (@3:15 it's the one on the bottom right and I'm pointing at it) and then slide the wire under the shielding. Put eMMC back on and attach the probe to the wire.
@falconmick Жыл бұрын
Do we need an special tool to measure like an oscilloscope? I’m trying to diagnose my wifi issue too
@jet613 Жыл бұрын
What temps? Also did you use a preheater?
@RetroTechCorner Жыл бұрын
I don't use a preheater - it's a small board so no need for that. As for temperature - I use 470C and varying airflow. You just need to know your tools - there's no "golden recipe".
@jet613 Жыл бұрын
@@RetroTechCorner I ended up using a preheater at 200f and my hot air at 350c and got the old chip off pretty quick! Downside I tried putting the new one on and pressed on it. Which shots some balls out :'(. And then I bumped some components tooooo. After I replace the components from a donor I'll have another go.
@michaelw9192 Жыл бұрын
Will the Nintendo Switch turn on and work without the wifi chip?
@RetroTechCorner Жыл бұрын
Not sure, will try in next few days and let you know.
@michaelw9192 Жыл бұрын
@@RetroTechCorner thank you.
@RetroTechCorner Жыл бұрын
ok, switch without wifi chip does work. Video proving it will be published today :)
@michaelw9192 Жыл бұрын
@@RetroTechCorner Thank you for checking that out. So I am trying to figure out why my Switch will not turn on. I have everything connected but the wifi chip because the wifi chip was causing the Orange screen of death.
@tungduy2469 Жыл бұрын
@@RetroTechCorner oh, really ?
@randomweirdyoutubechannel895510 ай бұрын
Mine just died today another chinese made piece of crap to throw away had almost everything fail since last year's heatwave