Like many other people in here also I would like to sincerely thank you sir for your time spend recording and explaining so many useful things. I also try to rebuild mine this will help me a lot I think.. Now I m about to remove the camshaft pulley. A local mechanic told me to knock it slowly around and will get off. Will see...
@vincentnettmann2688 Жыл бұрын
Thanks for a BRILLIANT instructional video. After watching it, I may even finally attempt to rebuild my clapped out 1400 engine. I really needed a good clear instruction video like this before the rebuild. For a few years now, I've dreamed of doing this myself. Being an electronics technician with only bicycle mechanics experience as a hobby, I haven't had the confidence until now to rise to the challenge. You see, a video like this one reveals sooo many procedures and "tricks" that only a very experienced master mechanic has well earned knowledge of. I'll be watching this video carefully over and over again in the near future, finally, I have the confidence to rebuild my fist engine... Baie dankie meneer.....
@carburettorrebuildservice8964 Жыл бұрын
Wow, thank you for the great reply. it makes me want to do more video's.
@lenndookun8478 ай бұрын
Amazing 😀 - Sir, how would you rate that Nissan engine A14? As I’m looking to buy a 2011 Kabbie with an A14 engine …
@zubairhaffejee170710 ай бұрын
Excellent Video and awesome job!!! 👌👌👌
@AshleyMckendree10 ай бұрын
I cant thank you enough for this clear, concise video that gets straight to the point!
@franciscocordova956115 күн бұрын
Wow, I love your video it was very helpful to watch. I learned a lot from this video. I have one question what type of oil do you use to lubricate the parts you put back ?
@kjtwesley8977 Жыл бұрын
Just so technically perfect. Thanks.👍
@carburettorrebuildservice8964 Жыл бұрын
Thank you
@JayJay-sq1wg Жыл бұрын
thanks a mil,Baie dankie
@vicdey63282 жыл бұрын
Great video sir!!!!!
@carburettorrebuildservice8964 Жыл бұрын
thank you
@marvingilliland Жыл бұрын
thanks for this I'm about to rebuild mine.
@carburettorrebuildservice8964 Жыл бұрын
I do hope the video helps, thanks for watching. we also have a facebook page.
@elswithprens261410 ай бұрын
Thank you for your time explain in fine details d patiently taking everything step by step. I will rebuild and clean my engine also by myself with these step you are explaining
@carburettorrebuildservice896410 ай бұрын
thank you for following my channel
@manueljose80299 ай бұрын
Good day good sir thanks for the amazing video. Im studying mac so it's really helpful. I have one question , what is the torque spec for the Nissan 1400 in Nm please if you could help. Please 🙏 🙏 🙏
@johnnydecarvalho98679 ай бұрын
Great learning
@carburettorrebuildservice89648 ай бұрын
thank you.
@txep21 Жыл бұрын
Baie dankie oom👌👌
@carburettorrebuildservice8964 Жыл бұрын
I hope the video helped you.
@soccerbettingandeverything2 жыл бұрын
Great video sir. Which socket are you using on the head cylinder bolts? Thanx
@owensharp85682 жыл бұрын
Size ke 14mm. Same as rocker shaft.
@gerriebarnard7 ай бұрын
Bou asb my A14 motor oor vir my porche spyder?
@kirisranchomicasa49984 ай бұрын
Question on my A14, I took it to the local machine shop to get rebuilt on the process of the build I came across some 79 mm forget pistons from B Project Japan as well bigger valves, stage 2 cam, aluminum flywheel from B Project Japan, after all this the builder is having problems with no oil pressure, any idea why? This is the 2 time they built it, the 1st time I drove it 18 miles and started knocking that's why I pulled out and took it to them..2 new oil pump any idea. Thank you blessings I enjoy watching your videos..
@carburettorrebuildservice89644 ай бұрын
It could be that the pickup pipe is damaged or partly blocked at the intake by the mesh wire. does your mechanic prime the pump before starting the engine? What make oil pump do you use?
@dylanbester4554 Жыл бұрын
Thanks for this vid. Do you have a resource for the torque specs for all the bolts ?
@moadventures1911 Жыл бұрын
If you got it please do share
@lamarfennell3367 Жыл бұрын
I’ve got the manual it has torque specs for everything I can email it to you
@user-lp4xo1ww6t3 ай бұрын
My carb leaks fuel the float bowl is running empty. I've checked the two bolts changed the washers no noticeable leaks on the outside but still losing fuel any advise
@carburettorrebuildservice89642 ай бұрын
Hi, what carby is it please?
@ThulzMtshoba4 ай бұрын
Good morning please if I may ask how much to do overhaul on Nissan 1400
@carburettorrebuildservice89643 ай бұрын
I have not calculated the cost in a while, wharsepp me on 060 654 6966
@colinnaidoo9618 Жыл бұрын
Hi there .. I'm building my Nissan 1400 engine A14 . What would be the cylinder head torque setting ?
@carburettorrebuildservice8964 Жыл бұрын
73.5 NM
@safwaankassim89044 ай бұрын
Hi there, please could I ask where do you get your engine rebuild kits from? I'm from Zimbabwe and I'm looking to rebuild a nissan 1400 however I'm struggling to find kits
@carburettorrebuildservice89644 ай бұрын
Alert engine parts Pretoria
@UnFiebru3 ай бұрын
Great video, My engine is in need of a full rebuild. Do you have any engines already rebuild for sale? I would really be interested in purchasing a15 engine. My car has a14. Let me know, also where are you located.
@carburettorrebuildservice89643 ай бұрын
Hi, i am in South Africa.
@wilfredoperez44168 ай бұрын
Beautiful I have a Datsun 210,1981 and I always wanted to rebuild the engine where do you get all the parts give me the website or address please thank you I like you videos.
@carburettorrebuildservice89648 ай бұрын
Hi, thanks for watching my videos. what is your location?
@gertdupreez-jc4yu Жыл бұрын
Awesome do you have a toyota 2.4 diesel video
@carburettorrebuildservice8964 Жыл бұрын
unfortunatly not
@shaunpotgieter4568 Жыл бұрын
Hoe kry mens die olie deur die motor voor mens start
@carburettorrebuildservice8964 Жыл бұрын
maak jou filter vol voor jy dit io skroef. haas die oil switch af en pomp olie daar in met a olie pomp. skroef dit terug en draai die motor met die starter met die coil draad af tot die olie liggie af gaan.
@siphoernest2278Ай бұрын
What are tourqe specs on big ends and cylinder head pls
@carburettorrebuildservice8964Ай бұрын
Look under files on my facebook page with the same name as thus channel
@SergioSimpson-ow8biАй бұрын
hi no file containing the torq specs sir?
@carburettorrebuildservice8964Ай бұрын
@@SergioSimpson-ow8bi Hi, i have just updated my Facebook page, it is now available again.
@shaunpotgieter9944 Жыл бұрын
Wat prys so motor
@carburettorrebuildservice8964 Жыл бұрын
To build it like this will probably cost around R8000, using good parts.
@hugonunez89868 ай бұрын
Any form of comunication on how to get in contact with you directly?????
@carburettorrebuildservice89648 ай бұрын
Whatsapp 060 654 6966
@repentanceministry87462 жыл бұрын
How much are you selling this engine
@carburettorrebuildservice89642 жыл бұрын
Hi, this engine is not for sale but i can rebuild yours for you.
@johnsenamela5340 Жыл бұрын
Good day. How much do you charge for a rebuild. And where are you at?
@hugonunez8986 Жыл бұрын
Where are you located so I can have mines rebuilt by a professional like you?
@schandrighklein31848 ай бұрын
Good day i am interested in this video what tis the reader of inlet valve and exhaust please 🙏🏻