Nissan Maxima Drivers or passenger side CV axle replacement full guide for all Nissan CV Axles

No video

Nissan Maxima Drivers or passenger side CV axle replacement full guide for all Nissan CV Axles

Рет қаралды 30,925

RB The Mechanic

Күн бұрын

Пікірлер: 78

@larryfreeman8699 3 ай бұрын

absolute best video I've seen yet. I'm trying to work on 02 sencers too upstream for Same car 2009 Maxima. do you have a video?

@RBTheMechanic 3 ай бұрын

Thank you should be very much similar

@dereklinfitt8875 Жыл бұрын

Very helpful video. I didn’t even bother to hammer at it to get it loose after watching the vid, I just took the power chisel to it right away and it popped off in few seconds. This video saved me $1,200. Nissan wanted $995 for parts alone. Thanks for putting this up.

@RBTheMechanic Жыл бұрын

Good job bro!!

@devonsstemcells1442 10 ай бұрын

When you chisel are you chiseling to seperate where they screw in and if so did it mess up the bracket on the car?

@jessemanire9733 Жыл бұрын

One of the best videos I’ve found so far !

@RBTheMechanic Жыл бұрын

Thank u

@tommymac3029 Жыл бұрын

Great video! I've watched a few videos on this process. None of them placed a pan below the trans. You definitely need to do that! The CVT fluid comes out, if it's not low like on this car. You also need to have a quart or two on hand to refill it. Mine was full before and drained out, when the axle came out. Thankfully I followed your procedure and didn't make a big mess in my garage! Thank you RB!!!

@RBTheMechanic Жыл бұрын

Yup

@mjarzoms 2 ай бұрын

Nice job man, well done. Brake rotor looked new, tie rods pretty much dead.

@RBTheMechanic 2 ай бұрын

Yes

@jerrydeguzman Жыл бұрын

Best video for sure! Clearly narrated...bada bing bada boom!...and clear shots. Wish I had a lift and impact wrench too, though!

@RBTheMechanic Жыл бұрын

Yeah bro without it will be hassle

@Revitloser Жыл бұрын

Perfect! Super helpful! Thanks for taking the time to put this together.

@RBTheMechanic Жыл бұрын

Glad it was helpful!

@DanielCobb-dd1zw Жыл бұрын

YO!!! FYI this perfect video shows you the exact same set up as a 2020 Pathfinder SV. THANKS BRO!!!

@RBTheMechanic Жыл бұрын

Oh nice !!!

@kylosolo8815 4 ай бұрын

You made this look so easy I will be doing this soon but I have to change hub bearings also....good times lol

@RBTheMechanic 4 ай бұрын

Oh cool I have video on bearings as well

@kylosolo8815 4 ай бұрын

I think I watched it,but I'll make sure need all the help I can get never did it before

@RBTheMechanic 4 ай бұрын

@@kylosolo8815 ok

@twotoned2774 Жыл бұрын

Easy to follow video. Very informative. Thanks.

@RBTheMechanic Жыл бұрын

Yup

@kiluhnic Жыл бұрын

Makes the job look easy!

@RBTheMechanic Жыл бұрын

Yeah not so bad to do

@deuce_deuce_4817 Жыл бұрын

Good video Brother. Thank you.

@RBTheMechanic Жыл бұрын

Welcome!!!!

@123dean4561 10 ай бұрын

good video thank u

@RBTheMechanic 10 ай бұрын

Glad you liked it!

@slappagiver8386 Жыл бұрын

So it’s the same process for an Altima going to be tackling one tomorrow

@RBTheMechanic Жыл бұрын

Similar

@revert2theStr8path 8 ай бұрын

Hi brother. You said don't use auto zone parts. Why is that? And which part would you recommend and what would be the price? I need to get it changed and I am asking so that no body rips me off and uses the correct part.

@RBTheMechanic 8 ай бұрын

I would go original or ac delco timkin is the brand I use $150 axle brand new no refurbished or core ford it

@revert2theStr8path 8 ай бұрын

@@RBTheMechanic and why would you not recommend the auto zone one? What could be the issue? I need one that ensures my car runs for atleast another year or so.

@RBTheMechanic 8 ай бұрын

@@revert2theStr8path because they rebuild it they don’t fix the acuator wear and tear new boot and greasing dosent mean. Axle is rebuilt it’s still will make click click sound. If they got core that’s a sign they refurbish them

@devonsstemcells1442 10 ай бұрын

Trying to do mine now and it won't come out. I guess I need an air chisel. Does it not mess up the part it bolts too?

@RBTheMechanic 10 ай бұрын

Yeah bang it with chisel

@claudius622 Жыл бұрын

Very good Video ! So on a 2001 it shoud be the same steps and no presence of transmission fluid ? Tks

@RBTheMechanic Жыл бұрын

I think 2001 is diffrent and fluid will leak out

@alexcaraway6537 Жыл бұрын

Hey bro do it gotta click cause it's not going in and I don't have no clearance for it to be push on a 2000 maxima it has a housing just with the house it just hanging

@RBTheMechanic Жыл бұрын

@@alexcaraway6537 which side

@mybrotherskeeperautocarell9600 2 ай бұрын

Where did you get the axle from because the autozone one doesn’t have the bracket

@RBTheMechanic 2 ай бұрын

My local part store

@macksauce9801 Жыл бұрын

Where did you get your cv axle from? Dealership are extremely high on parts.

@RBTheMechanic Жыл бұрын

I purchased it from buywise auto parts in NJ north.

@kash4550 Жыл бұрын

Does this have to do with the transmission driveline also ?

@RBTheMechanic Жыл бұрын

This is part of powertrain connected to transmission and puts out power to wheels

@jeffkovene4420 Жыл бұрын

Be very careful putting the axle into the tranny! It's very easy to tear the seal!

@RBTheMechanic Жыл бұрын

Yupp

@rudymarius1706 Жыл бұрын

How much you charge for a job like that?

@RBTheMechanic Жыл бұрын

This was total like $390

@rudymarius1706 Жыл бұрын

With parts or just labor?

@RBTheMechanic Жыл бұрын

@@rudymarius1706 with part

@rudymarius1706 Жыл бұрын

I had the axle done and A/C compressor cost me $600 in labor $350 in parts felt like price was high and could of done it myself but I'm in New York and it's cold so I just paid the man

@Ahamilton89 Жыл бұрын

I have a 16 Nissan Maxima platinum v6 3.5 . The axle is stuck. Any advice

@RBTheMechanic Жыл бұрын

Which side axle? And stuck where in hub on other side

@Ahamilton89 Жыл бұрын

@@RBTheMechanic the passenger side. I’m not sure where it’s stuck. I think I’m the middle. 2 mechanic tried to get it off for 8 hours with no success.

@Ahamilton89 Жыл бұрын

@@RBTheMechanic it didn’t budge at all

@RBTheMechanic Жыл бұрын

@@Ahamilton89 the bearing u have to use air hammer or pry bar did u take off the bolt off the bearing in center

@Ahamilton89 Жыл бұрын

Thanks so much. I’m having another mechanic work on it tomorrow. The other mechanic gave up. I’ll let the new mechanic know if he runs into the same issue. I really need my car fixed.

@Alanthe918mobilemechanic Жыл бұрын

Make sure the shafts tip isn’t running against anything while u try nd remove it I find a hammer 🔨 to always be enough if I hold it straighter and tap it and rotate it it comes

@JesusTracksTV Жыл бұрын

I thought you were going to show the driver side

@RBTheMechanic Жыл бұрын

It’s same process just easier dosent have the center bearing pop the axle out with pry bar

@trippsharpe6950 Жыл бұрын

How long in total should this take if your doing it “@ home”

@RBTheMechanic Жыл бұрын

40 minutes

@kevinkieel6778 Жыл бұрын

YOU CAN NOT DO IT ON JACK STANDS... YOULL BE SCREWED... STRUTS YES AXLES NOOOOO!... VEHICLE NEEDS TO BE IN THE AIR ESPECIALLY FOR THE PASSENGER SIDE. TOOK ME 2HRS OF AIR CHISLING

@RBTheMechanic Жыл бұрын

@@kevinkieel6778 jack stand is tough

@Sroor2023 Жыл бұрын

@@RBTheMechaniccan be done I did it before on jack stand both sides but passenger side is pita to get it out

@RBTheMechanic Жыл бұрын

@@Sroor2023 yeah

@kash4550 Жыл бұрын

Could this leak transmission fluid ?

@RBTheMechanic Жыл бұрын

Well there’s axle seal at the point where axle enter’s transmission that could be bad or get damaged when doing the job u have to be careful when installing it

@Alanthe918mobilemechanic Жыл бұрын

Does this apply to a 2017 Altima

@RBTheMechanic Жыл бұрын

Yup

@RBTheMechanic Жыл бұрын

Might be but diffrent but over all similar