I have a brand new Ruger with brand new BX-25 mags and they all feed poorly so I appreciate this video. I agree Ruger should be ashamed to produce these magazines without properly testing them for functionality. I saw a video where they fix the internals, I will try that first since it is an easier fix. If that does not work I will surely do this fix. thanks! And Bartosz, your English is just fine, very understandable.

Great permanent solution to a problem that many 10/22 users run into. You did a great job of both explaining and demonstrating it. Thanks.

Your English is fine along with tip and explanation !! Very good!!!

This works GREAT! I too was disappointed in my beloved Ruger when I kept having trouble with the BX-25. I followed your instructions and now have 2 perfectly functioning mags. Thanks very much for the video.

The mag being loose is not the only problem of this magazine. These mags have an internal problem as well, when fully loaded sometimes the rounds are pointing horizontally rather than slightly upward causing a failure to feed. The follower inside is also too loose and doesn't always line the bullet correctly to point toward the chamber.

Your English is fine. Thank you for helping all us Ruger 10/22 owners.

Just took my brand new 10/22 out this past weekend with BX25 mag and jammed so much I couldn't believe it

I just bought a kidd extractor and kidd plunger with stiffer spring for $20. Fixed problem!!

I have the epoxy and I have a dremmel. Nothing is stopping me now. THANKS BRO.👍👍👍

I think your English is great. Thanks for the video!

Small strips of Velcro that have tape on one side work well also. I just bought a Ruger 10/22 Charger. The 15 round mag it came with works fine. The two BX-25 mags I ordered won’t feed at all. The shells sit with the tip of the round facing downward. I disassembled the mag, took off the red plate, cut a .22LR round down so that it fits over the the small red rod going into the red plate & now my shells are angled correctly! Great video brother!

RUGER WE LOVE YOUR 10/22s please fix this ! ! !

Just bought my first Ruger 10/22. I was bummed as the BX-25 didn't feed at all after multiple tries. Worked perfect with the stock 10 round mag. It's a bummer as this seems to be quite a common problem. Thanks for taking the time I'm going to add to the list of possible fixes.

Great video! No problems understanding your English . Ruger should have made them as wide as the 10 round mags. If you compare them side by side you notice that the 10 rd mags are wider and fit snugly . So you just have to increase the width on the 25 rd to match the 10 rd and it will fit as snugly and not have failures

Looks inside mag well you can see threaded screw points for adjustment. They are 12-24x-1/4 stop screws. They will push mag and adjust angle to where it needs to be. Cheers good luck.

Cabinet door bumper pads They sell them at Walmart for $3-4 They work great

Hey, greetings from the American south!! Thanks for the video! Your English is much better than a lot of the people I know who live in the United States, so don't ever think that you don't speak English fluently. Also, If you ever need any parts for anything that are hard to get where you live, feel free to message me. I have a license to buy/sell firearms and parts, and I'd be more than happy to work out a way to send them over to you. I know magazines and some accessories are not allowed to be exported a normal way, but any springs or small parts or anything like that aren't regulated at all so they wont be a problem. Keep up the good work, and keep shooting!!!

You have done a wonderful job informing and instructing us to fix a well known problem Ruger should have addressed many years ago. Ruger continues to sell a product that will not work in their own rifle. My Ruger performs flawlessly with the 10 round rotatory mag and fails continously with the Ruger BX-25. I have tried a variety of "hot" ammo and the BX-25 is useless. How can a company and a gun with such a good reputation let a problem like this continue? A very bad business model., but thank you solving the problem.

Bought two BX 25 Ruger Mags for my 10/22 takedown...terrible gap and wobble. Thought something was wrong with gun... replaced trigger assy with Rugers accessory 2.5 lb pull trigger assy, put the swiss extractor in, still problem. Ruger took it back and went completely thru it and returned to me a new (bolt/receiver) gun. Better, Thank You Ruger, nice try and appreciated...but still occasional failure to eject. Have used tape to build up mag and eliminate wiggle as experiment, works. Will build up as Barosz shows in his excellent video. PS...Bought two Pro Mag 25 and they are worthless. The magazines will not hold 15 rounds before burping them out like an auto feed...yes, that is out of the gun. Sometimes they would just stand the first round straight up like a rocket. Sent them back to Pro Mag at my expense...had to ask what happened to them 2 weeks later...they sent me replacements (not sure they were any different) which have exactly the same problem. Don't buy Pro Mag garbage.

I tried your 25 round magazine repair. Wasn’t as pretty as yours and I didn’t have metal bonding epoxy… But my clear 5-minute stuff gets as hard as the polymer magazine casing. With my CCi polymer-coated high-velocity 22LR shells I shot 50 rounds without a single jam . Cheers, Alan

Ruger should hire you, seeing as nobody at Ruger knows how to design a reliable mag.

When I built mine I got the volquartsen tg2000 trigger group. It’s designed to make the mags fit tighter

I just cut some sections of sniper tape and wrapped the whole top section of the mag where it fits into the mag well. You just need to be accurate and careful to cut holes for the sprung fittings, but the tape worked perfectly for me. After thousands of rounds and several hundred insertions and extractions of the mag, I refreshed/replaced the tape and away I went again. No glue, no fuss, no drying time or Dremel/sanding. The advantage of the tape was it also removed all side to side movement of the mag when inserted. The original 10 round mags feed perfectly as do the two BX15 mags I have. The BX25 was terrible originally, but the tape trick worked fine. Now my 1022 is fitted with an Arthur E Brown M1 carbine stock, iron sights again, and I bought two new 10 round mags and then epoxied the Arthur E Brown dummy polymer M1 carbine mags onto the bases of them to complete 'the look'. It does look pretty cool and is a handy little 'replica' M1 carbine. (Living in the UK, we cannot own live action M1 carbines!! So my 1022 is the closest I will ever get!) and the advantage of the dummy mags is they provide an excellent handle for loading and unloading the 10 round magazines into the rifle. I have retired my BX25!!

Thank you! Just purchased 2 BX-25 magazines (from Ruger) and both of them stovepipe and misfeed regardless of what brand of ammo I use. I might try your modification but not until I give Ruger a call. I agree 100%, how can such a reputable company as Ruger continue to sell faulty magazines...Shame on them!

I have had a 10/22 in my collection for many many years and never had any problems except when the orignal mag was dirty after cleaning no problem.....Also I use Butler creek hi capicity mags and have never had any trouble....I have put may thousands of rounds downrange.

i haven't had a problem with the bx25 mag but i will definitely remember this awesome video thumbs up

OK, I tried this fix last week but it did not fix my feeding issues with the BX25's. I also tried the 22lr case bushing trick on the follower, also didn't help. BUT I just replaced the stock Ruger 10/22 extractor with a Volquartsen Exact Edge Extractor and my feeding issues are GONE. I also replaced the extractor on my Ruger Mark IV (same extractor) and it has also fixed it's feeding issues!!! I just ran about 500 rounds between 2 bx25's and 4 Mark IV mags and not a single issue!

i cannot thank you enough for making this video. I will follow your steps. I am experiencing the exact problem that you referred to. I called Ruger and nobody called me back. I am going to buy the stuff tomorrow and get to work on this. I’ll chime back in afterwards and let everyone know how it went!

I just bought some new BX-25's and the issue has not been fixed by Ruger. Thanks to you, I plan to follow your tips for fixing.

I hear from many people that have tried the long magazines that they all jam, or have feeding issues. This makes perfect sense to correct the feeding issues. Thank you for s goodvideo and sharing your discovery.

Actually your English is better than alot of English speaking people.

Thank you for the video and the idea. I changed the product and shortened the wait time. I used the JB Weld steel stick and didn’t have to wait because the product is already the consistency of putty when the two parts are combined!

Just back from the range conducting an experiment. Firing my 10 22 with bx 1 three types of ammo, bx 25 three types ammo and modified bx 25 as shown in this youtube having zero play in the mag. Federal supressor and federal copper plated hollow point fired flawlessly two mags each. Federal lead round nose match jammed every 3 to four rounds also fired two mags in a row. I am now convinced that the ruger mags are not the cource of the jam problem. Seems the gun is sensetive to the ammo used. I had two boxes of aquila left and tried them too, it jamms. I went back to suppressor and shoot flawlessly two 25 round maggs. I had my wife,s ruger 22 lcp, it also jamms with the bad ammo. I strongly feel that using the right ammo is the solution to smooth shooting. Love my ruger ec9s 9mm, shoots any ammo with no problem seems that small caliber guns have small tolerances and therefore selective with the ammo.

Just ordered a BX25x2 should I have any problems with it, I'll do the bushing fix first, try that, and if I still have issues I definately keep this in mind.... Thanks for another fix!!!! Your English is great, especially considering you're translating technical terms. Thanks again for the video.

Excellent detail video! the standard 10 shot magazines are rotary, bit like a revolver. these are linear fed by a leaf spring. Well done on the video, very clear and concise!!

Ruger BX-25 magazines are made for multiple ruger 22 lr type rifle that's why it's not a snug fit and some has feeding issues but it can be fix easily.

Bro you for sure helped me. I just bought my son a 10/22 because everyone I've ever shot has never ever jammed or malfunctioned in any way. His came with one 15 round msg and two 25 attached mags and flipped opposite ways. The 15 jams a little but both 25's jam iF AND THAT'S A BIG IF they EVEN go into battery. Thank you for your help I'M DOING THIS IMMEDIATELY 🤙

A couple of strips of duct tape fixed mine.

Well done job, good work on your part. Your "fix" makes sense & you applied your idea for a solid job. I think the word you were looking for is "cure" what the epoxy would do during the 10 hour time period.

Excellent video and very good demonstration of both the problem and the cure. And your English is excellent. No apologies necessary. Thanks!

Thanks for taking the time to make this video. It's very helpful for me, as I'm having the same issues!

You have your scope mounted 90 degrees off the up down turret is to the left and your left right turret is on top.

I have never liked long mags. I use a clip that allows three standard ten round mags to be joined together. Works great.

You are correct, shame on Ruger for not correcting this long standing issue

Thanks for taking the time to make this video. It's very helpful. Great job.

Thank you , this is much better than many other attempts at correcting the magazine issue. I will also try this on the non-ruger magazine .

Thanks for the vid and by the way your English is superb

You had a soldering iron right there. Just stipple that bar area. And it would have filled the gap without the glue. I have done this with the internal of an AR stock to take slop out. Prevent rattling. If it too tight just sand a little until fits to your liking. And nothing in between to come off. Or jam.

I "might have a simpler fast fix using a rubber band. I was having trouble with my brand new magazine. I simply used a rubber band going from the mag to the barrel band. It holds the mag at the angle you mentioned. Goin to the range sat. I'll report back one way or other.

Fantastic info thank you. I have 5 BX-25 round mags and they are all shit. I used 500 gt sandpaper to smooth in the ramp on the mags just to get them to feed.

I tried something similar to this and it didn't work very well plus mixing two part epoxy is a hassle. So today I came up with something better that isn't messy but is a little challenging. I had some 5/32nd acrylic sheet that I fabricated into 1/4" wide strips and attached them vertically on the sides of the back of the magazine with double back scotch tape. I ground the factory bump down flat where I mounted them, with my dremel. You have to make sure that they don't interfere with the capture/release button in the mag well. It totally solved the front/ back play but I'm still thinking about something similar to this to fix the side to side play.

This has been an issue since they started making these mags, I have a BX25x2 magazine the doubled version, it fits just as poorly as the regular BX25 mags. Shame on you Ruger is right, you would think that they'd have corrected the issue by now and recalled the old mags that don't fit properly and replace them with new improved models. Terrible waste of money for me because the BX25X2 isn't cheap..think I paid around 50 bucks for it so I'm a bit upset that it does not function like the standard 10rd mags do....how the hell did they get the measurement so off on the BX mags when they already had the 10rd mags to go off of...sheesh...step it up Ruger, you're slacking. I now have 3 ruger different rugers that all have slight issues like this as well...malfunction one way or another or have imperfections you wouldn't expect from such well known and supposedly respected producers of such products.

Great video and work. I haven't had any problems with my set up. the 30 year old Butler Creek mags work fine in the 45 year old 10-22. If I decide to get hi-cap Ruger mags I'll do this first.

Dear Mr. Bartosz Bodnar, I am VERY happy you made this video, thank you! I really like the method you used, and the video is very easy to understand, a very well made video. Thank you for helping your fellow Ruger owners!

Thank you so much! Whatta clever fix, I will try this one!!! Are there any tuning tricks for the BX-25 internals?

Damn good video, very clever solution! I've got a Ruger precision rimfire that takes the same mags. Came with 3- 15-round magazines. They all have the same problem. The slightest bit of pressure on the magazine will cause a hang up. I've got some JB quick, some masking tape, and a Dremel. I know what I'll be doing with my time later, thanks!

Good explanation of the problem and repair, thank you.

Hey dont worry. Your english is great. Dont apologize for it. Thanks for the video bud.

The only fix I've found is that the back of the feed ramp has a taper to it unlike the 10 rotary mag that has to be filed flatter and the 4 mags I have work perfectly after that mod. Check it out and compare it to the 10rd rotary and you'll see what I mean. The 10rd is flat on the back of the up coming feed and the 25rd has a taper. I filed them down semi flat and have no more problems.

Your English is fine and I understood every step....Thank you for the video, it helped me fix my problem.

Nice job, my 25 rd mag already does pretty good but this would clearly help. However I have a 110 rd drum I believe I'll try this on because it struggles more than the mag also the upgrade bolts help as well.

Your English is fine. Good material description. Excellent demonstration. Thanks. A person could male the lumps less high to make fitment faster.

Great idea and I'd really like to see how well this lasts over time and many times of using the mags.

Thanks, tight can be too tight, the mag should fall out of the well when ejected so it looks like some testing needs to be done. Oh Boy! I'm heading to the range!

Never ever had a issue with bx mags. I own twenty of them and two 10-22 rifles. They perform great.

I have two 10/22s. One runs perfectly with both Ruger BX25s and Butler Creek 25 round mags. The other won’t run with the Ruger mags and also with the newer Butler Creeks. It never has problems with the older Butler Creeks. I’m going to try this on a couple mags to see if it solves my problems with that rifle. It would be nice if all the mags ran in both guns!

Mine only has an issue with the first one or 2 rounds out of the bx25 mag when i use hollowpoints. If i only load 20 rounds its fine. I can load all 25 rds without issue with round nose bullets both plated or lead either one.

the primary ejector is on the magazine on the 10/22. that fucked up angle can eject a cartridge too soon and end up with a stove pipe. ive seen it demonstrated

Can also use a couple layers of duct tape around that area to stabilize it while the mag is seated.

Yup. Same problem here. I got a two-pack of them and one seems to run great but the other was jamming the round cocked up and all that. Very disappointed in Ruger for putting this out there in this condition. Its ridiculous.

Great video. Appreciate your attention to detail. Your English is just fine. Thanks!

Fantastic job mate, and an awesome e long term fix to those sloppy bastard BX25 mags. Love ya work champion!!!!!🤙🤙🍺🍺🍺🍺

Buy a ProMag like I did ! Its perfect for not only 10 rounds, but also 15 & 25 rounds meanwhile its cheaper than Ruger .... ! Here in the U.S. we have people coming from all around the world, not all can speak perfect English ! Like a guy from the U.K. come to the U.S., the way he speaks is different from local American ! We can well understand you English .... its nothing to be sorry or shy, you just present yourself ! 👍✌

I LIKE YOUR ENGLISH ...LOL IT WORKED PERFECTLY..!!!! TIP ==== GO SLOW TAKE YOUR TIME "DON'T RUSH"

I’m not sure but I believe Ruger did fix the issues with this mag. I bought a new one earlier this year it is very tight and has had no malfunction issues so far after shooting a 1000 rounds or so at steel challenge matches. I’ll fix my other, older mag, using the tips here.

You can fix it with a cut down 22 case or a smaller bushing for the mag follower on eBay. The follower tilting from the slack in the loose bushing causes the problem. $10 shipped for a correct size bushing on eBay & etsy

Thank you so much for the info. I will try it before the next time I go to the range. This makes so much more sense than the 22cal. spent cartridge follower fix on youtube.

Outstanding!! [and don't worry -- your English is a whole lot better than my Czechoslovakian!]

Thank you very much Bartosz.

I have an SR .22 Ruger rifle and I use the BX-25 MAG so far I have not had any problems but this look like a good idea

I've never had any feeding issue except for running out of bullets.

Maybe that's why Bill Ruger didn't think we needed more than a 10 round mag

Thank you very much for sharing your DIY video!🙏

Don't worry ur english is pretty clear!!! Good job!!!

They make little round and square pads of all kinds that are extremely sticky on one side, rubber/vinyl or felt on the other. Look in the 3M tape area of your local hardware store of choice.

Great video! I thunk I'm going to try this on one of mine and see how it goes. It seemed like the fit was really tight, maybe too tight. Maybe one or 2 light passes with a fine file would leave it snug but not too snug.

Thanks Bartosz, very well presented!

So mr. video explainer, the reason for the size difference is that the ten round is a ROTARY mag. The BX25 is single stack.

I use an off brand BX25 style mags and they work perfect for over 3 years and many thousands of rounds. If you buy the off brand ones just make sure they have the steel feed lips

My new BX-25's don't wobble like that and I still get 4/5 misfeeds per mags and I've tried every kind of ammo under the sun.

I HAVE THE HCMAGS HC3R(HIGH CAPACITY RAPID RIFLE RELOAD) THEY FIT TIGHT & WORK PERFECT EVERY TIME.

Pretty ingenious

First don't worry about your English, you're doing just fine, and great video, thanks again for your thoughts and great video

Hella work!!!All you need is to put piece of duck tape your good to go..

Very helpful and informative video. Thank you.

That’s a lot of work but a good solution I know a lot of guys including myself use duck tape on the mag to make it fit tighter it’s a lot easier to do and faster but your solution looks a lot better and more permeant and fits tighter just time consuming but seems to be worth the time I will have to try this

great video man. amazing work 👍

Very clever. Great video.

Exactly right. Shame on Ruger for not being on top of the poor Chinese quality control.

Very helpful, your english by the way is perfectly fine!