No Money Needed for These Sawmill Upgrades (they're simple, I promise)

Рет қаралды 15,223

Жыл бұрын

Don't get me wrong, I really enjoy sawing lumber. There are days however when frustration kicks in and I'm about ready to hang up my hat. Today however is not that day as I tackle two small things that are a source of my frustration at my sawmill. If you saw with a Woodland Mills sawmill on a trailer you may have experienced the dreaded clunk of the log stop or log clamp falling out of their mounts as they hit the ground. This has happened one too many times for me and today I"m finally doing something about it. I've got the old arc welder out hoping to shed some light on the situation and make things more comfortable for me out at the sawmill. Although these "fixes" are somewhat of a trial and error, I'm hoping I come out with a good addition to my sawmill. You can be the judge of that one though haha. Glad you're all here for today's adventure, let's see how we make out. Here we go!
Sawmill shown in this video: Woodland Mills HM130max Woodlander XL
woodlandmills.ca/hm130max-woo...
‪@woodlandmills‬ #sawingwithsandy #discoverthewoodland

Пікірлер: 123

@sawingwithsandy Жыл бұрын

On second thought, I"ll likely grind off the weld I put on the log stops and put the weld on the side of the log stop to allow for a flat surface where the lumber will sit. Alternatively I may end up just rotating the log stop around so the weld faces to the side or back. See how it goes.

@earlzathome Жыл бұрын

I always have the angled side facing the log anyway, makes the log easier to roll when using the can't,.and if it does ride up a bit because it isn't straight, the angle makes it ride down instead of OVER the stop....if you add more holes for measurements, maybe do them in the other face, 90° from the holes now, so you don't weaken the stop....

@thomajason Жыл бұрын

I was yelling at my screen "No Sandy, drill the holes on the sides and weld on the back" The bolt heads and weld will stop your log stop from holding the wood square! Did we start that project after finishing a 6 pack?

@Z-Bart Жыл бұрын

Yes. I was concerned you would mess up your ability to square the cant. Great ideas though.

@WideCutSawmill Жыл бұрын

Why not put a small tack weld (only 1/16” tall would do) on the corner of the stop in line with the t bolt so as you crack it loose and it slides down, the tack sticks out and catches on the bolt? Unless there is not enough room in the sleeved tube.

@mcollier-xr6bm Жыл бұрын

Great ideas. I added a bolt, nut and jam nut on the log clamps for easy removal if needed. Thanks for the videos.

@sawingwithsandy Жыл бұрын

That would do the trick!

@SuperHurdman Жыл бұрын

No Maple Syrup this year Sandy! I did some but it wasn't a great year was all small quantities picking up sap this year! I was home to my Mother's and stayed three months and when I got back we had a lot of snow I usually just cover my little sled and it is lost under the snow somewhere so we did everything with snow shoes going to boil 150 + litre's this Monday.

@sawingwithsandy Жыл бұрын

Sounds like some great syrup is coming right up!

@tomt8320 Жыл бұрын

Hi Sandy. Thanks for another great video. There is my hammer again at 17:06! 😂

@sawingwithsandy Жыл бұрын

hahahaha

@tjjewell4115 Жыл бұрын

Nice fixes for your Sawmill to make your life better.

@sawingwithsandy Жыл бұрын

Thanks TJ!

@johnaddis1022 Жыл бұрын

Ya know when the snow finally melts we wont recognize your place LOL . I to have used nails and bolts for pins when I didn't have cotter pins available, You can lay your welding rods on a tray on top of your wood heater to warm them up before welding in the winter time done that before and if your rods are in the metal container just set that on the wood heater too, couldn't hurt! Jla🤠

@sawingwithsandy Жыл бұрын

I like that heating idea John!

@TheBeardedCarpenter Жыл бұрын

Howdy Sandy- good tips on easy updates for the mill. Hope you’re having a great weekend. God bless

@sawingwithsandy Жыл бұрын

Thanks for that! Having a great weekend

@russellbelliveau1694 Жыл бұрын

Looking like spring ! Those little upgrades go a long way when you’re sawing for sure !! Great job 👍

@sawingwithsandy Жыл бұрын

Thanks Russell! I"m sure hoping this warm spell keeps up here

@jeffhuffman5433 Жыл бұрын

I like your idea Sandy it's simple, easy and effective and cheap and those are always the best options. It'll save time and make it easier. Thanks for the tip Sandy.

@mikecameron5322 Жыл бұрын

Thank you for the idea's. Finally got my 130max all together, 10:00 Saturday will be my first day of sawing

@sawingwithsandy Жыл бұрын

Hope it goes well Mike!

@TheFlatlander440 Жыл бұрын

Good idea there Sandy. I was thinking using hitch pins for the log stops would work as well. I purchased a variety of hitch pins from Amazon for under $20 USD and they have come in very handy. If you don't want to do that perhaps fasten a couple zip ties around the bolts and attach them to the frame (somehow, haha) so you won't lose the bolts. Have a Happy Easter Sunday. Cheers!

@sawingwithsandy Жыл бұрын

I like those hitch pin ideas! I’m going to have to try those! Happy Easter

@WideCutSawmill Жыл бұрын

Definitely a worthwhile project. 👍🏼

@RaperJason Жыл бұрын

Yet again another great vid Sandy I have noticed a difference between the Canadian and the UK Mills the holes the log stops go into have two additional bolts on the back one top and one bottom so you can adjust the angle of the log stop to get them perfectly upright I do have the HM126 so that might be the reason but I found when I started cutting Trapeziums a quick adjust squared everything up Also agree with the other comments of turning the angled stops the other way round I mill some large diameter logs taller than the stops and they don't get caught up when you turn them if the 45 is towards them

@sawingwithsandy Жыл бұрын

The Canadian sawmills also have those adjustment holes. I just haven't had to use them fortunately as the log stops were perpendicular to the log bunks. The option to make those small adjustments are nice though for sure.

@shayneralston990 Жыл бұрын

👍 On my way to the shop to make the upgrades.

@sawingwithsandy Жыл бұрын

Always a good day when headed to the shop!

@critical-thought Жыл бұрын

Great ideas! I will be making similar upgrades on my sawmill now 😊

@sawingwithsandy Жыл бұрын

Glad I could spark the idea

@danielnicholls6868 Жыл бұрын

i like the 7014 welding rods to they work well.

@sawingwithsandy Жыл бұрын

For sure. Once I found them they were my goto as they seem to do a good job all around

@brianwestveer9532 Жыл бұрын

Another job to add to my list. I really hate leaning over picking up all the time, great idea. Just finished watching the OUTSIDER on his cabin build he has alot of snow too.

@sawingwithsandy Жыл бұрын

Thanks for coming along for the video Brian.

@mlafond9369 Жыл бұрын

Allo nice improvement bravo👍

@wallaceviviansadventures2095 Жыл бұрын

great job little jobs go along way. i put a leaver valve on my water sure made a big difference on the water flow.

@sawingwithsandy Жыл бұрын

Thanks for that Wallace!

@marvindiamonjr.9631 Жыл бұрын

The short log stops that came with my mill had a piece of keystock welded to them to keep them from falling through the mount. Not sure why they didn't do that to the longer ones also. I will be adding a bolt to the bottom of my clamp, though. That thing can be frustrating if it falls at an inopportune time. I ordered the new scale marker that you had in a previous video. That should be here soon. I've really picked up a lot of good tips from you over the time I've been watching. Thanks for sharing your experiences!

@sawingwithsandy Жыл бұрын

Great to hear that Marvin and I'm happy to help where I can

@earlzathome Жыл бұрын

Once again nice fix for an annoying little issue! My HM126 isn't on a trailer, so when I made feet for it I made them high enough so the stops can't fall out - your way would have been easier! I could watch you riding that trail on the ATV all day, beautiful day for it!

@sawingwithsandy Жыл бұрын

Thanks Earl! Hope you're enjoying the 126. I like those machines. Was a great time out on the ATV. always like finding time for a ride

@leonkaczor2405 Жыл бұрын

Good job!!

@sawingwithsandy Жыл бұрын

Thanks Leon

@delmanicke9228 Жыл бұрын

Nice video, already did those great ideas. They work and they are helpful. 👍

@sawingwithsandy Жыл бұрын

Thanks Del!

@thebradleysoncatbirdhill6849 Жыл бұрын

Sandy...I am really grateful that you are sharing all of this knowledge. Just getting started with my HM130 Max, and I'm soaking up everything. 👍👍👍 Much appreciated!

@sawingwithsandy Жыл бұрын

Glad I could help and I appreciate all your support

@bd19992006 2 ай бұрын

I have a hm 130 max as well, I put a longer roll pin in the bottom of my log clamp, no more falling out.

@sawingwithsandy 2 ай бұрын

That’s a great idea!

@bay9876 Жыл бұрын

Like the old Canadian tradition for repairs, out come the duct tape, eh? "If the ladies don't find you handsome, they'll at least find you handy," Red/Green

@sawingwithsandy Жыл бұрын

hahaha that's the way

@Wheelloader__ Жыл бұрын

Nice video Sandy

@sawingwithsandy Жыл бұрын

Thanks for coming along for the video!

@johnwoody4905 Жыл бұрын

good video and job. only thing i would do diff. i would use a bent rusty nail for luck. i cuss the roll pins in the log dogs all the time they are always getting hung up i need to grind them all down flat. take care, be safe and well.

@sawingwithsandy Жыл бұрын

Thanks for watching John and happy sawing !

@Grunt49 Жыл бұрын

Saw a welder set amperage low,allowed electrode to stick to metal.Broke free,turned up amperage and went to work.Said it heated and dried out electrodes.YMMV

@sawingwithsandy Жыл бұрын

Yeah always a bit of a guess with my old machine as the settings are too accurate I find

@carlmclelland7624 Жыл бұрын

Sandy, I yelled and screamed at you but I guess you didn't hear me! You welded the bead on the wrong side of the log stop. I see under your pinned comment you figured it out. Hey, we both know you wanted to play with the grander, as well as the welder. One other thing, if you put a bolt through the log stop to hold it at a specified height, do you still need to clamp it? When you push the log against it, I don't see it going anywhere. Great solution with the nail thru the log clamp!

@sawingwithsandy Жыл бұрын

hahah I had a second look when I was posting the video this morning and realized that I should probably move the weld but in the meantime I"ll try it out and just turn the log stop 90 degrees if I need to. I don't think I"ll need to clamp the log stop anymore if the bolt goes through which will be nice actually

@BissellMapleFarm Жыл бұрын

Maple season is over for us in Ohio. I have some SWS catching up to do!

@sawingwithsandy Жыл бұрын

Hope the season was good for ya! Getting real warm here this week as well so likely over for us as well real soon

@richardmontei7084 6 ай бұрын

I see you corrected your problem.

@danielnicholls6868 Жыл бұрын

grind the weld off of front to keep front straight and notch each of the tapered sides for a 3 inch piece of 3/8 bar and weld across.will let it stick up just a bit to grab👍👍

@sawingwithsandy Жыл бұрын

I like that idea right there!

@contrafax Жыл бұрын

It is very satisfying when plans work out, isn't it?

@quarlow1215 Жыл бұрын

This is a great idea. I've just assembled my mill and haven't even started it yet but this is a mod I will do right away except I'm going to grab some of those pins with the spring lock. Like the kind uou find on an RV landing legs or on certain farm implements. I didn't like your nail idea because if there's something pointy I'm going stab myself on it 😂. Thanks for the hack.

@sawingwithsandy Жыл бұрын

I like that spring lock pin idea!

@quarlow1215 Жыл бұрын

@@sawingwithsandy lol, I haven't even got my mill all set and I ran out this morning and picked up 6 of those pins. Showed them to my buddy and he thought was a great idea too.

@dustinmorin2335 Жыл бұрын

I did the same with the weld on the log stops and works great for me

@sawingwithsandy Жыл бұрын

I'm looking forward to trying it out real soon. Good to hear you've had great luck with it.

@newsnowriversidesgtrock8144 Жыл бұрын

My suggestion instead of the nail would have been a cotter pin. Easy to install and easy to remove if needed. Now it will be a pain to take the nail out if necessary.

@Logi_432 Жыл бұрын

Great video it was really interesting

@sawingwithsandy Жыл бұрын

Thanks for that Nikolas

@MichaelPMc Жыл бұрын

Often packages of those clip pins like used to lock trailer hitches are on sale at princess auto, I expect there would of a size that would work better then a nail, I have purchased a package with all different sizes.

@ryanklingerman1975 Жыл бұрын

Looking forward to spring but not the bugs.

@sawingwithsandy Жыл бұрын

I hear ya there Ryan!

@roberto.peterson9917 Жыл бұрын

Suggestion 3 point / pins with bail or spring pin to keep pins from undoing

@sawingwithsandy Жыл бұрын

That would do the trick!

@09FLTRMM77 Жыл бұрын

MM77 Approved 👍🏼👍🏼

@sawingwithsandy Жыл бұрын

Thanks for coming along!

@robertwazniak9495 Жыл бұрын

Instead of just a spot weld, take an old nut and weld it on. The spot weld is rounded and will jam into the sleeve tube if you just let it drop sometime. And, it will be a real pain to drive it out from the bottom. Ask me how I figured that out.

@sawingwithsandy Жыл бұрын

I like that idea with the nut. Thanks for sharing that Robert

@mirceanouradachian9168 Жыл бұрын

👍👍👍💙💛❤BINE GANDIT. BUNA SANDY! 💙💛❤👍👍👍

@exotictones1054 Жыл бұрын

70's n 80's here the last week almost.you would think the company would take care of all those easy fix problems on those mills.

@sawingwithsandy Жыл бұрын

Sure has been some nice warm temperatures here this week as well

@bryansaunter4124 Жыл бұрын

My trailer is 8 feet wide, yes it is horrid when they fall under, happens lots. The log clamp will accept a bolt thru the gap at the bottom. Are you turning log stops so the weld on knob is on the side not against the log.?? Easy fix thanks for the idea, like the bolt thru stops great idea

@sawingwithsandy Жыл бұрын

Hey Bryan! I think for now I'll turn the log stop 90 degrees but may end up moving the weld if I don't like that turning. Lots of good ideas I"m reading about in these comments I may give a try for version 2.0

@deprived56501 Жыл бұрын

Nice simple fix. I don't really see the need in bending both ends of the nails over like that though. As long as the nails have a big enough head on them, that end isn't going anywhere. Adding a slight bend to the other end would keep it in place and allow you to remove them should you need to with much less fiddling about. Also, wouldn't the welds just add to the gripping ability for the log stops? Good vid again. Thanks.

@sawingwithsandy Жыл бұрын

All good points Joe. Only trouble with the weld placement is if I want the lumber to sit flat against the log stop . I'd have to rotate the log stop around in that case likely

@newsnowriversidesgtrock8144 Жыл бұрын

You put the weld on the face side that holds the log in place and attempts to keep the cant square. If you put the welds on the sides that would not be an issue!

@natedscate Жыл бұрын

Perfect sense, he will always be a 1/4" of, the thickness of the weld.

@sawingwithsandy Жыл бұрын

For sure. I end up turning the log stop either 90 degrees when I need the perfectly flat surface or all the way around 180 degrees to get around this

@MadWeedi9192 Жыл бұрын

Hi!👋 Good yob!👏👍 My Lantzmann bs790 sawmill dont have this problem,i get stopers and holders,i skip this 🙈😅😂

@sawingwithsandy Жыл бұрын

That would do the trick. Thanks for coming along for the video

@saintaugustine1715 Жыл бұрын

I was going to mention something about that soldering and interfere with the sitting of the log but I see you figure it out yourself I can of was thi king the same for the hole you did they should of been side way instead of the way you done them that you could of left the bolt in without interference P.S. by the way I am kind of surprise that you don't do a little bit of maple syrup for yourself unless you don't have enough mapke on your propriety well have a great day

@sawingwithsandy Жыл бұрын

I do typically do maple syrup but have been quite tight for time the last few years unfortunately

@robertwalker8052 Жыл бұрын

hi sandy !! love your videos...I just sold my 122 and have a 130 max on order!! does the 14hp electric start have a charging system to keep the battery up ?? also does the 130 max come with short and long log stops ? thanks !!

@geoffreykail9129 Жыл бұрын

Did you take the long road to the mill cause it was such a nice day? LOL

@sawingwithsandy Жыл бұрын

I took the only road hahah . Actually there's a few roads to get to the mill but this one was the only one cleared

@jbarlazye911 Жыл бұрын

A bit crude but Good fixes for a problem Woodlland should have already addressed!!

@sawingwithsandy Жыл бұрын

Thanks for coming along for the video

@johncayouette6468 Жыл бұрын

Use cotter pins or rivets in place of the nails for a more professional look

@sawingwithsandy Жыл бұрын

That would do the trick for sure John

@barryjohnston1027 Жыл бұрын

Tent peg bent

@rexmccomb7589 Жыл бұрын

I would have cut a small piece of pipe and then in half and weld that on to the log stop so you have a little handle on its on the side

@sawingwithsandy Жыл бұрын

I like that idea Rex. I may have to make a version 2 and include the handle idea!

@rexmccomb7589 Жыл бұрын

@@sawingwithsandy awesome i will be watching

@fredanderson5544 Жыл бұрын

how 'bout a bucket or bag to catch sawdust as it comes out of the mill?

@sawingwithsandy Жыл бұрын

I like that one Fred. I tried mounting a bucket to a hook on the side of the mill and that works well but in my sawmill the bucket hits the post as I cut so would have to move the sawmill over a bit

@mikegb1969 Жыл бұрын

Split pin!

@sawingwithsandy Жыл бұрын

I haven't heard them called that before. Here they sell as roll pins

@mikegb1969 Жыл бұрын

@@sawingwithsandy roll pins here too! meant split pin the type you fold back. rather than nail.but as u say nail costs nothing.

@JonHirsch-tp7vc Жыл бұрын

You put your clamp in backwards its supposed to lean toward the log not away if you look there is a thin side and thick side on the mount

@sawingwithsandy Жыл бұрын

I actually was waiting for someone to spot this. You're right there Jon. I never noticed until recently and have been meaning to get things turned around.

@mlafond9369 Жыл бұрын

Salut I just bought myself a sawmill, it will serve me well Merci Mario (Google translate)J’espere que c ok, désolé