Great Job! Very professionally done! Jonathan works like magic! I wish I could find such service professionals here. Amazing skills! I have a Siemens IQ300 and I just started getting the bearing noise. It is about 4 or 5 years old. The service centre told me when noise gets worse replace the full drum set. That's the type of service I get here. Thanks for posting the video.

This video was of great help when recently the bearings went in my IQ700 it was 10 years old and had never broken down. The bigger bearing was in a terrible state, the ball bearings had started to come out. It was a devil to get out but I did it. The limescale was awful but it looked nearly new after a lot of cleaning. Machine is now back together and working. If it does another 5 years I'll be happy. Also replaced the pump as well. Thanks very much.

Have been looking for a dismantling video for my Bosch Logixx7 WIS28440GB/40. This Siemens iQ700 video is exactly the same as the Bosch.👌😉👍👍

Wonderful details and explanation thanks. Guys coming from service companies always try to force entire drum replacement even for a machine of just 3 years old saying all sorts of non-sense to rip off a higher charge for service but is clear here how only a bearing can be the reason for drum noise due to rubbing.

11k views and not even a snarky comment? Wait, I think I just made one.. So I just finished the job with the help of this video. I'm a pretty handy mofo, I must say, and I've got most any tool one might want, if I can just find them. Had already been in there to replace the water pump a few months ago. Even so, the thought of splitting the drum was probably the most fearsome proposition for me. Meh. It goes pretty straightforward, and with a little gentle prying side to side of the ample pinch points, it comes right apart. I did place a meager bead of silicone on reassembly, IMO o-rings exhibit a little compression after some 15 odd years... a few scrap 2x4s come in very handy for this project. I used a one to drive the new bearings flush, then used the old bearing as the perfect size to drive home the new one without damaging it. I didn't remove the soap tray, just weaseled my way around it on disassembly. If you have a family member (or a thirsty crony that your wife disapproves of hanging around), it does help to have them help with the re-install of the tub assembly, as it's a bit unwieldy. Definitely remove the cement counterweights. I'll sign off now, before this comment becomes more tedious than the job itself. I actually felt a sense of great accomplishment on completion of this project. I figured even a scratch and dent machine goes at least $800-$1000, so where could I get paid close to $200 per hour for my labor? Turns out, right in my own basement, just a few steps from the refrigerator always stocked with my favorite forms of re-hydration! Enjoy the fruits of your labors my friends!

Great video - very many thanks

Sir, my seimens iq300washing mechine making too much noise before motor starting.where is the noise coming from? Motor and drum bearing is OK. Pls help me sir

Hi would you be able to put a link and provide spelling of glue you mention? Is silicone almost as good (hence the use of it in this instance)? Thank you.

On reassembly he's tightening the shaft nut good and hard with a torque wrench - what torque setting is appropriate?

भैय्याजी..... That Was The Wonderful Wonderful Video.

Hi i have a siemans iq100 the bearings are gone i followed your video on the iq700 and have the case out that houses the drum but the iq100 has no screws or bolts how do i separated the casing to get the drum out so can replace the bearings i searched your channel but can't find anything on the siemans iq100. Thanks

Hi, nice video, do you know if the new washer bosch siemens still apenable and fixable? Or are becamed all ne peace like most brands? Thank you! Any way, the inside still very clean...who use it, jnow how to use it properly, powder only and 40 degrease minimum

Wow! If all the Brittains work that fast they shouldn't have any problems after leaving the EU. Howsoever it's really a lot of work and so I decided to buy some ear plugs instead of replacing the noisy bearings.

Thanks

Great video. What size threaded bar did you use and what was the diameter of the washers?

How to open the locks of the plastic tub

How old was the machine ? Is this a common problem ? Would you recommend the Neff/Bosch/Siemens products ? Thank you

What can you do if you have a sealed drum? Thank you.

Turkiyeden selamlar kasnak vidasini kaclik lokma ile actiniz acaba

How 2 Repair Motor and Other pasts When Seimens IQ500 Waterflood Half of The M/C

What will be the price for a job like this?

The gufero, specifically the space between the blades, should be filled with titanium zinc vaseline, not dishwashing liquid. 😱

2.12 why???

I need to repair washing machine it is noisy

L 2