Non-Stop BUSINESS Use for ONE YEAR! Ortur Laser Master 2 Pro Review & Custom Grid Wasteboard

Рет қаралды 42,052

Күн бұрын

🔗 Buy the Wasteboard Grid File Here: samcraft.shop/products/ortur-... 🔗 The Best Lightburn Test File Package: samcraft.shop/products/comple... ⬇️ MORE LINKS BELOW ⬇️
🔗 Fusion5 Tablet: amzn.to/3EL1hUF
🔗 Bluetooth Keyboard: amzn.to/3vBBIRC
🔗 Battery Powered Magnetic LED Lights for Laser:
🔗 Ortur Laser Engraver: amzn.to/3EKrYbW
🔗 Ortur Laser Enclosure: amzn.to/3OESBDG
🔗 Ortur Z-Axis Adjuster: amzn.to/3fXneI1
🔗 4" Round Slate Drink Coasters: amzn.to/3fT9Sg2
🔗 4" Square Slate Drink Coasters: amzn.to/3EhRmao
🔗 Lightburn Software for Lasers: lightburnsoftware.com/
🔗 All my Laser Videos: • Laser Engraving Business
🔗 Our Family's Small Business: greenacrehomestead.com
🔗 Watch The New Shop Build Videos: • 12x20 Workshop Build
🔗 Make Money Woodworking Videos: • Making Money from Wood...
🔗 My Website: sam-craft.com
🔷 ABOUT SAMCRAFT 🔷
Samcraft is a channel all about educating, inspiring, motivating, encouraging, and sharing the things I've learned since starting my own small business in 2018.
Today on Samcraft I'm sharing my experiences from using the Ortur Laser Master 2 Pro laser engraver over the last year. I talk about the good things, bad things, servicing the laser, cleaning the laser, and much more. I also design and show my grid waste board for the laser, which you can buy the plans from my website to help support the channel.
🔷 VIDEO CHAPTERS 🔷
0:00 - Intro
0:48 - NOT A SPONSORED VIDEO
1:24 - Ortur Metal Enclosure: Good or Bad?
3:50 - Making a Custom Wood Wasteboard
5:05 - Cleaning and Inspecting the Ortur Laser Master 2 Pro
7:24 - Mounting the Wood Wasteboard
8:11 - Fixing the Laser Head Wire
9:21 - Condition of Laser After 1 Year of Use
9:36 - New Wasteboard Grid File Design
10:07 - Tablet & Keyboard Used with Laser
11:24 - Crashing the Laser Head
11:37 - Fixing the Crash Issue & Mistakes
14:07 - Engraving the New Wasteboard Grid
15:29 - Design Features of the Wasteboard Grid
18:16 - Purchase the Grid File for Your Laser!
18:46 - One Year Later: What do I Really Think of the Ortur Laser Master 2 Pro?
20:36 - Closing Thoughts & Thanks
21:14 - Blooper Reel
#laserengraving #woodworking #samcraft
*DISCLAIMER*
This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue making videos like this. Thank you for the support!

Пікірлер: 177

@glennanderson8783 Жыл бұрын

Sam, this type of video is what separates your channel from all the other folks out there in YT land. I see a lot of people demonstrating machines but no one except for you ever goes back to show all the maintenance needed to keep things running. Full marks on this one Sam. 👍👍

@darleneclark6098 Жыл бұрын

He is definitely a cut above the rest in yt land.

@Samcraftcom Жыл бұрын

Thank you Glenn, I appreciate the comment!

@huntingtimes5474 Жыл бұрын

Really!

@gabrielgreenham5320 Жыл бұрын

Very well said.

@TheNurseArtist Жыл бұрын

YES... couldn't agree with this more. Sam.. keep up the great work.

@Mostaism Жыл бұрын

Love your work and professionalism champ. Keep on keeping on

@tombenton8397 Жыл бұрын

Always enjoy your videos, and am glad to know that after a year you are still using your ortur laser. I am still trying to get started with mine.

@AlwaysCensored-xp1be Жыл бұрын

You keep impressing me with all the practical info and methods. Simple and effective.

@TheFlamingEyeball Жыл бұрын

Bloopers are always fun. Shows how hard it really is to be a one person production unit KZfaqr! I have the Ortur Laser master 3, and I'm really enjoying the addition to my shop as I learn it.

@jamesharless5357 Жыл бұрын

Great video Sam, love the bloopers!👍🏻

@mikepetitt9624 Жыл бұрын

Thanks Sam love your channel because you always keep it real! Always great info!😊

@Samcraftcom Жыл бұрын

I appreciate that!

@cheriethompson7725 Жыл бұрын

Thank you for sharing. I do have the cheapest outro it does a light burn. But I like the way you shared everything.

@howdydoody30204b Жыл бұрын

Another great video! Glad you're back. Will the waste board file work for a standard LM2, as well?

@MO-wv5qh Жыл бұрын

Love the out takes!!!

@onsapplikasies8620 Жыл бұрын

Thank you for taking the time to make this video.

@Samcraftcom Жыл бұрын

My pleasure!

@beasluszka6258 Жыл бұрын

Worth the watch for the Spider at the end. Laughed right out loud.

@dee1959ful Жыл бұрын

Great information for use of the light engraving.

@stellaunger8568 Жыл бұрын

Entertaining Sam as I know nothing about what you showed- I do enjoy your videos however. Your clarity of speech and educational information is fun for me to view. Thanks

@SandhillDigger24 Жыл бұрын

enjoyed this Sam. Until seeing this video, I had no idea that this thing even existed outside of large commercial applications. It was a good tour of how this operates and let me tell you brother, the quality of your videos is very professional and entertaining. Love the bloopers too

@Samcraftcom Жыл бұрын

Thank you so much! I try very hard to make as good a presentation and "flow" to my videos as I can. Happy to share the fast-growing world of hobby laser engraving, too! :)

@danofiremano Жыл бұрын

Nice update video, thanks!

@vickyrupe8999 Жыл бұрын

That’s a neat machine you have really given me some good ideals. Thank you🤙🤙🤙🤙🤙

@LuanNguyen-pl2wf Жыл бұрын

Love your content Sam, keep up the great work

@Samcraftcom Жыл бұрын

Thanks, very happy to hear it!

@TheOneCoop Жыл бұрын

Sam, been enjoying your video's for months now and this video sold me on buying my own Ortur. I recently (6 days ago) bought the Laser Master 3 and I now have it up and running the first burn. I'd love to know what you did to handle fumes/smoke/etc before you got the enclosure for your LM2Pro.

@randy2283 Жыл бұрын

Great video good to see you again

@mikehamlin9748 Жыл бұрын

Love your gridboard idea

@tonnyahogan2203 Жыл бұрын

THANK YOU FOR THE INFORMATION SAM

@castercrafts3190 Жыл бұрын

Well I just entered the club with the Ortur Master 2 S2 so the smaller brother to try. I am hoping to do engraving to brand my product and maybe some custom work also. Never know where the rabbit's hole will take us. Enjoy your videos keep up the great content.

@Damon_Barber Жыл бұрын

Hahaha!! I was about to say, “Just flip it over!” And then you flipped it over and showed us it’s already been flipped once. LOL! Way to make the most of what you have. 👍

@Samcraftcom Жыл бұрын

I knew someone would be saying that! LOL Glad I left that part in the final video. :)

@darleneclark6098 Жыл бұрын

You always pick the best background music 😂 although most of this is above my head, but I find it fascinating the way you explain things.

@Samcraftcom Жыл бұрын

😁

@stvcolwill Жыл бұрын

Thanks so much for leaving the spider incident in there!! that was epic fun (of course, after the fact). : )

@printnub7585 Жыл бұрын

Spider! Holy Moly! My reward for watching to the end. Nice video!

@JupiterFerrari 8 ай бұрын

RE: 21:22 - Well THAT caused an unexpected belly laugh! Thanks Sam, I needed that today. 21:38 - This one too! :)

@studiosbt Жыл бұрын

An informative and refreshingly honest presentation, about what you do and don't do.! Excellent patter and very listenable to.! One thing about that bottom board, would it not be better if constantly loading coaster etc for engraving, to have small raised ply forms or keeps so that you are 100% @90 degrees in line? Just "L" shapes as not all coasters are exact same size. I am sure someone will have mentioned it before? And, if u r doing different work, u can always slide in another thin board on top and it should still be in focus range, depending onthe item being engraved. Good luck with the series - I enjoy watching and isle be back - for tips as soon as i get my X20 built up & sorted into a proper site.!! [ Using Laserpecker 2 atmo!]

@iamsource4me Жыл бұрын

I am as impressed with your presentation as I am with the clarity, completeness, and usefulness of the material you discuss. Your personality is perfect for this and your diction, vocabulary and continuity control are valuable assets that make your videos a pleasure to watch and listen to. I am an editor for 7 best-selling authors, so I have some knowledge of what makes a good story (in their case) or a good presentation in yours. Keep it up kid (I’m 90) you’re a natural. Oh, I have a LM2 Pro sporting a 40W laser head and control it with Lightburn on a dedicated desktop PC running Windows 10. P.S. How can I buy you a coffee [or an adult beverage if you prefer] ?

@aussiegolddogcnc3d412 Жыл бұрын

Great video Sam. Really enjoyed watching. Cheers Robert

@Samcraftcom Жыл бұрын

Many thanks!

@screamingdeamon341 Жыл бұрын

Wife bought me an ATOMSTACK, for Christmas. I didn't think I'd ever own a laser, but it's still a LOT to soak in. So I'm watching several makers with lasers. I really enjoy how you explain things, for us older not so tech savvy folks. THANKS

@Samcraftcom Жыл бұрын

Congrats!! Which model did you get?

@norm5785 Жыл бұрын

Wonderful video, thank you for sharing, stay safe happy and healthy, from Henrico County Virginia

@raymondshell8579 Жыл бұрын

Just purchased this wasted board for the coasters and it's awesome..... Thanks

@Samcraftcom Жыл бұрын

Great to hear! Thank you for your order Raymond!

@davidorf3921 Жыл бұрын

Interesting that it was so clean. I suspect that will be down to a few things but the biggest will be what you are engraving, if that is mainly slate coasters theres not a lot of really nasty sticky residue going to be given off, unlike many other materials

@TP-si3km Жыл бұрын

😃👍Danke für das Video. Gute Idee

@cheriethompson7725 Жыл бұрын

Have a blessed week

@karencary3312 Жыл бұрын

Love ALL your videos.

@jeffbarnes2014 10 ай бұрын

Hello Sam , First off I want to say I think your one of the most genuine people on KZfaq, your honesty is genuine . I am in the process of buying a laser. WOW so many choices . I want a cabinet , air assist and easy Z adjustment. I keep leaning to the Adomstack . My biggest concern is power of the machine , I am looking at there 33W version . All i want to do is basically what you are doing along with building some small boxes, tumblers, earrings and pictures to wood. Do I need a 33W or is that to powerful . Should I just get a 10W or 20W. I know it’s his is a lot and you are busy, if you have time I look forward to your reply . Thanks

@jasontraud8102 Жыл бұрын

When working with multiple machines (cnc, laser, print farm). I've had the best luck just using a dedicated mini pc without a monitor or keyboard. Then just using my primary laptop to remote into it to setup jobs. This also has the added benefit of being able to use some USB cameras can monitor the setup while I'm out of the room. For some setups you can do it cheaper with some raspberry pis but the control and slicing software may not be able to run on a Pi.

@Samcraftcom Жыл бұрын

That's an interesting solution for sure! :) Ahh the good ole rPi. Brings back memories of my past life in IT and making remote sentinels for network discovery and monitoring at various locations.

@mikeE0055 Жыл бұрын

I have some of the product from this machine. It does a great job! I’m going to order more in January.

@Samcraftcom Жыл бұрын

:) Thanks Mike!

@steveferguson1232 Жыл бұрын

Sam, this a great unexpected video. Most guys out there barely go over assembly when they are sent a laser and frankly don’t know what they are talking about. Going over the maintenance is genius. Haven’t seen first one showing this. And you always talk safety about everything you do. Great one here. Ideas for future SamCraft. You need storage so let’s have some woodworking making storage. Like a work table tat holds your new saw with a t track or dog hole top to hel with assembly of projects. Yo and Angela and your whole& amply is great.

@Samcraftcom Жыл бұрын

Some soon-ish upcoming videos will be building my new tool wall for behind my island work table, as well as building LaserTown (a dedicated 12' wide bench space in the shop for the laser engravers and their accoutrements). I've been pondering what to do with my new table saw and have considered a rolling island workbench. Just needs to be the right size, too. The workshop is only 12x20 and has quite the assortment of tools. :)

@maryjanecreate Жыл бұрын

Bur you have wheels!😄

@judyp1214 Жыл бұрын

😂😂‼️ the tutorial was way out of my pay scale but love to stay for outtakes👍

@saj9814 10 ай бұрын

Is the diode LU2-4 ... SF or LF? Thanks for this video. Very helpful

@Greg8872 Жыл бұрын

how funny this came up today, my LM2 just arrived! Now I just have to figure it all out.

@Samcraftcom Жыл бұрын

Awesome timing then! You’ll like it. I sure have!

@deannaoverstreet4146 Жыл бұрын

Thank you Sam!

@Diggar72 Жыл бұрын

Thank you for your honest feedback. I've been looking at getting a laser engraver just afraid it's gonna be way outside my wheel house. Pretty technically challenged over but think it would definitely add a ton of value to my lil shop.

@Samcraftcom Жыл бұрын

Hopefully I helped some. :)

@sharonedwards7821 Жыл бұрын

Came over from your family channel, gonna binge watch for a while 😊

@kscheuerman5378 Жыл бұрын

Yes Sam, this older lady found your video to be interesting, educational (even though most is over my head) and also entertaining!! Oh, I enjoyed your reaction to the spider. That wasn't fair, he blindsided you

@Samcraftcom Жыл бұрын

Glad you enjoyed it! Yeah the spider totally did a sneak attack on me. 😂

@thesplinteredfinger Жыл бұрын

Your bloopers crack me up!

@Samcraftcom Жыл бұрын

Glad you like them!

@bigdave6194 Жыл бұрын

I added the Laser Module Kit 450nm 80W with Air Assistance, 10W Optical Power, LASER TREE Laser Engraver Module Head, Double Ultra-Fine Compressed Spot and love it. I still have the original and will use it as a back up. I just needed more power and wouldnt you know it they come out with one 2 mos after I drop 280 bucks on a new diode

@Samcraftcom Жыл бұрын

Always happens that way, doesn't it! :)

@ChristinaWelch Жыл бұрын

Great video Sam!

@Samcraftcom Жыл бұрын

Thanks!

@HalfAssHomestead Жыл бұрын

I have the Ortur Laser, (my worst one), the FoxAlien, (better), and the XTool D1, (the best diode laser I own). My favorite of all though is the OmTech 60 Watt CO2, that thing is a beast, and comes with both air assist and built in exhaust fan. Lasers are great for doing all kinds of stuff, and they are fun to experiment with.

@Samcraftcom Жыл бұрын

From an observer’s perspective (me), the xTool D1 Pro does look to be one of the best diode lasers on the market today. I totally agree re: CO2 lasers though… there may be one coming to the Samcraft shop soon. ;) That will be a new learning curve for sure, but I’m eager to really be able to cut materials in a business capacity (i.e. faster than an hour per job).

@Forest_Actual Жыл бұрын

Thank you!

@hydinout 6 ай бұрын

I'm giving some thought to grabbing one of these but I was wondering if you could give a review or info on engraving glass, crystal, or metal in general?

@user-qp3wx4me1l 4 ай бұрын

I have exactly the same set up you are using and the Lightburn software also. I haven't used my device for over a year and am ready to start playing again. I intend to purchase your Lightburn waste board file and utilize it for placement and designing just as you showed in your video. I was hoping to not remove my metal bottom plate on my device and was wondering if that amazing file could be sketched/burned/marked directly onto my bottom metal plate? What are your thoughts on that possibility? Your videos are the best! Your bloopers make you "real". Thanks in advance.

@aaronromero7723 4 ай бұрын

I just got one. But I can't figure out how bro frame the objects. Help here . Nice videos

@johnscuderi271 Жыл бұрын

Sam until you get an air compressor, get yourself a pack of Dust Off. Its a Electronics gas Duster. It works great on my keyboard, and other electronics I have.

@sleepindagarden2600 Жыл бұрын

That was a very informative video. Thanks for that, because I have been wondering whether I should get one. Curious of your recommendation between this and the S10.

@Samcraftcom Жыл бұрын

I'm not sure what you mean by S10. There are so many lasers and models that I'd need to know the brand too. :)

@sleepindagarden2600 Жыл бұрын

@@Samcraftcom Sorry, I mean Sculpfun

@briandowns7742 Жыл бұрын

Fantastic content as always Sam. I see you are using the Manual Z axis lifter mechanism. Did that installation reduce your workbed area from 400mm x 400mm to 400 x 380mm on the Y axis? What bed area dimensions did you put into lightburn when you added the device as my machine crashed into the x axis bottom frame when trying to engrave my workbed at 400mm x 400mm

@Samcraftcom Жыл бұрын

Looking under Edit->Device Settings in Lightburn I have a Working Size of 15.748 in for Width & Height. My Origin is lower left.

@sunhawk61 Жыл бұрын

let me tell ya, I get the ibby-jibbies from spiders also. Pretty good move ya had there.

@clydedecker765 Жыл бұрын

Spider! Not a fan myself but I definitely do NOT freak out. The closest I ever came to it was that tarantula in Roswell. It was crossing the road at night as I was heading home. It was 6 - 8 inches across each section of its body and all legs were over 10 - 12 inches long I thought it was a possum crossing the road - it looked that big. As I got closer, it continued to saunter slowly across the road. I waited until it was out of sight before continuing. Roswell has a lot of them in their desert like territory. I have since found them all over southern New Mexico and Arizona. They are pretty harmless and keep certain populations under control. Scorpions, mice and rats do not like them FUR SHURE!

@Samcraftcom Жыл бұрын

The proximity got me rather than the species. :)

@openhostwebservices6086 Жыл бұрын

love me some of them sparks when plugging in the 24v adapter lol. You could have just painted it white as well and engraved it black lines. Sand and paint and when you need a fresh one repeat sand and paint which again.

@Samcraftcom Жыл бұрын

Well dang... I didn't think of paint! That's a great idea!

@homezero Жыл бұрын

Have you already completed a video on maintenance for the Shapeoko? I'd like to see that if you have. Keep up the great job you are doing here on Sam-Craft!

@Samcraftcom Жыл бұрын

I’ve not, but that is so over due! I’m getting the shop in order more day by day and will soon be ready to actually fire up the CNC again. It’s been storage for so long… will be interesting to see what needs adjusted!

@homezero Жыл бұрын

@@Samcraftcom After watching your assembly video on your SPXXL, I ordered one. Your video made assembly a breeze. I feel I may be due for some maintenance so I look forward to your video on that topic. Mine runs very well, knock on wood, there may be room for improvement. 😛

@joshengland5251 Жыл бұрын

Maybe u could make a how to run video using lightburn? Just like a simple engrave like if i went and bought it,all the hookups like u have and like a walk thru video or tutorial on how to use the lightburn as u do...also do u ever use the rolling tumbler setup? Thanks man...live the inspiration...really thinking i want one...

@Samcraftcom Жыл бұрын

I've wondered about making such a video, but worry it may be very dry... I'll ponder on how to spice it up and make it fun but also be properly informative. :) I have the rotary for the machine, but honestly haven't ever used it. I need to spend some time learning the ins/outs of it. Many others use them and like them!

@johnbiggi3738 Жыл бұрын

Hey Sam, what are the inside diameters of your laser? Like what would be the largest cutting board you could put in it to ingrave?

@foundrylabz Жыл бұрын

What a great video. Love all the fine detail you go into with everything. I do not own a ortur laser, but still a lot of great points on how to get stuff done and cleaned. So, o a, going to add my 2 cents worth here since you are thinking on getting or upgrading the computer for the laser and future ones. I highly suggest at least 32GB RAM with about 1TB of SSD storage and a good CPU like a good i7, i9, or i5. Windows 10 pro would be ideal with staying away from windows 11 at all costs for "NOW"... Hope this helps. If you can afford it, 64GB RAM would be better. Hey now, what happened to that daddy long legs ehh?? ROFL!

@Samcraftcom Жыл бұрын

Great points all around. :) I'll be repurposing a computer I already have, but upgrading it a bit too before it makes its way to the workshop. It's a small Lenovo ThinkCentre. I have an SSD and RAM upgrade coming in the next week that will give it plenty of power for lightburn and the likes. ETA: No spider were harmed in this video.. but were tossed outside! LOL

@foundrylabz Жыл бұрын

@@Samcraftcom Good call on the spider... Them creepy crawlers give me the creeps too. On the PC side... I think your doing good. Even an i3 is good combined with a SSD HD. But don't hold back on the RAM because that is KEY...

@wb2ire Жыл бұрын

Sam. Did you blow out the vent fan?. 🤔 great videos

@marcbarash6045 Жыл бұрын

great information

@Samcraftcom Жыл бұрын

Glad it was helpful!

@reymoreno4801 Жыл бұрын

What kind pf laser machi you recomend for engraving guns or gun parts.

@domingodavaloz3422 Жыл бұрын

Will you be reviewing Ortur Lazer master3

@herkleslie4561 2 ай бұрын

niiiiice video tyvm

@lasermethod Жыл бұрын

Can you make the grid file for the 850mm X 410mm. Or show to make the grid file for it?

@howdydoody30204b Жыл бұрын

Does the Ortur Z-axis adjuster give you more travel down? I have taller feet (20mm of lift) on my LM2 and need to get the focus lower. I bought an after market 3D printed adjuster, but that isn't working for a number of reasons.

@teresamccrary3604 Жыл бұрын

What will this laser do on Sublimation Blank Coasters?

@TheSaltyVetUSN Жыл бұрын

What would you suggest for someone thats never done laser engraving and is on a strict budget to buy as their first engraver?

@fk6823 7 ай бұрын

I wish there were metal enclosure options available

@otakelblanchemanor0659 Жыл бұрын

Hahahahaha ....SPIDER! That made my day! Hahahahaha

@terrypen Жыл бұрын

22:00 hahaha it's a daddy long legs.... You scared the crap out of him and he jumped across your laptop!!!

@Samcraftcom Жыл бұрын

Twas the proximity to my face that got me. LOL It was on my shoulder. I carried it outside and it live... no doubt to return for another visit soon. LOL

@terrypen Жыл бұрын

@@Samcraftcom I would say that you scared it more than it scared you, but I'm not too sure!!! hahaha

@zipit-media Жыл бұрын

I bought that "Laser Head Focusing Controller" - "stop" extender - gcode the extra weight ? Also the scale that's less than 15.748in? Have you done that before ?

@Samcraftcom Жыл бұрын

I honestly don't know what you mean?

@heffe2001 Жыл бұрын

I'd be surprised if someone hasn't mentioned it already, but there are cable chain designs for that x-axis wiring just like you're using on the y axis (I'm currently at about 8:22 in the video, so if you address this in there, I haven't heard it yet, LOL).

@heffe2001 Жыл бұрын

I'd also suggest making the area of your waste board separate from the wood that attaches to the bottom of the laser enclosure, so if you need to replace it, you just slide it out of the laser, and slide in a fresh new piece. It'd make maintenance a bit easier, and you could have one waste board set up for, say spoons and such, another set up specifically for coasters.

@tonnyahogan2203 Жыл бұрын

SPIDER!!!😂😂 MY KIDS ARE TERRIFIED OF SPIDERS TO

@axeldejesus2060 Жыл бұрын

Hello Sam. I just watched your video about making templates for the laser machine. I am new to lasering, in fact I just got an Ortur Master 3 today and this is my first. I am interested in making multiple coasters at the same time and would like to make a template for 9 coasters. My question is how I make sure I place the template on the right position all the time, so my coasters are aligned properly and will engrave where they need to be engraved. I have not put together the machine yet so I'm not sure if there are mark or guides that will help with the position of the template on the laser bed. Could you please let me know? Thanks.

@Samcraftcom Жыл бұрын

That’s exactly why I like to mount the lasers to a plywood sheet. It locks the laser down to the wasteboard and then allows me to engrave my template without any fear of it moving. The biggest thing to remember is to always use ‘absolute coordinates’ when doing this method. That sets your job origin as the homing point of the machine and allows repeatability time after time. I’ve probably engraved about 1,000 coasters with this style method and never had alignment issues that weren’t human error. :) Congrats on the LM3! I have a slew of companies trying to get me to make a video on it and am considering it. I’m curious to see how better it is than this model.

@Damon_Barber Жыл бұрын

Without an air compressor you could use compressed air from a can for cleaning computers and accessories.

@corydebuhr4344 Жыл бұрын

So what watt Lazer did you get?

@prestongriffin416 Жыл бұрын

SAM can use use your every day computer to run light burn or do you need a different computer.. Preston

@Samcraftcom Жыл бұрын

Lightburn will run on any average computer, it's pretty lightweight.

@jeffmiller7277 Жыл бұрын

Would it cut medium density fiber board? I make architectural models, kind of doll houses but not. Also do I need a huge computer?

@Samcraftcom Жыл бұрын

Not as-is. You would need a different bed (metal with air gaps), and an air assist setup in the least. I only engrave with this machine -- no cutting. IMO if you want to cut, get a CO2 laser.

@TheSMEAC Жыл бұрын

Thanks for the video… wouldn’t a cheap camera make these adjustments and stock placements super duper easy and also add overlays as a big benefit to your operation that will work with every laser you run lightburn on?

@TheSMEAC Жыл бұрын

BTW: the other question I had was, do you run a line after fill on your engravings or does it not make a difference since you don’t use air assist.

@Samcraftcom Жыл бұрын

Perhaps? I've not delved into the world of adding a camera with lightburn yet to know if it would be easier or faster for setup and running jobs.

@Samcraftcom Жыл бұрын

All of my engravings are just 'fill', no lines afterwards.

@scottlittfin5832 Жыл бұрын

I noticed you used that metal cylinder to set your Z axis for focus. That would place your "focal point" at the top surface of your board, correct? Now if you put your slate on the board, wouldn't the focal point be at the bottom surface of the slate rather than the top of it? Or, is that metal piece cut to length to account for the slate thickness?

@Samcraftcom Жыл бұрын

The metal cylinder came with the machine and is to be placed on top of the surface you are engraving.

@scottlittfin5832 Жыл бұрын

@@Samcraftcom Doh! I feel stupid, LOL. I completely overlooked that you have easy Z axis adjustment and would therefore set your focus for each job. I do not have Z axis so I end up putting ceramic tiles under each leg of the frame to raise the whole thing up by the same amount as the thickness of the tile I am burning and then fine tune the focus with my lens adjustment. Thanks for the quick answer to this "braindead" old man, LOL.

@lynnobrien9429 Жыл бұрын

Spider part was funny, but I'm scared of spiders to. that was a daddy long legs harmless as can be.

@Samcraftcom Жыл бұрын

It wasn't the species, but the proximity of it to my face that got me. LOL I carried it outside. :)

@fancylady4386 Жыл бұрын

DO YOU HAVE CUTTING BOARDS?

@charlesrosenbloom4140 Жыл бұрын

what is the time to do a 4" square coaster?

@Samcraftcom Жыл бұрын

It averages about 6 minutes per coaster.

@sverrijoensen Жыл бұрын

Still using it or does the Gweike Pro does all the work now? :) I've also got the Ortur Laster Master 2 Pro. Starting a little business to save up for the Gweike Pro. :D

@Samcraftcom Жыл бұрын

No Gweike Pro in my shop.... yet. :) But even after.. I don't see phasing out the Ortur for my coaster engravings. It's so handy!

@78harj Жыл бұрын

sam wat cheap engraver would u recommend im just starting out we have chatted b4

@Samcraftcom Жыл бұрын

If you're only going to engrave, and not on metals, I would recommend the Genmitsu Jinsoku LE-1620 as a great starting setup. That's one that I have personally used and like. I have a video on my channel about it, too. kzfaq.info/get/bejne/gN2ce6aK0rrIp6s.html

@TheWoodHaven Жыл бұрын

Guess who just reached out to me for a colab video? It rhymes with more tour.

@Samcraftcom Жыл бұрын

Saweeet!!

@TheWoodHaven Жыл бұрын

@@Samcraftcom False alarm. Must have been a drive by prank. As soon as I said I was interested, I got ghosted. I was actually looking forward to learning about lasers. Now I"'m even more intimidated...just kidding...mostly.

@curtisaitken7027 Жыл бұрын

Looking to buy my first laser. I am a woodworker. What machine do I start with?

@Samcraftcom Жыл бұрын

That depends most on your budget and intended uses (engraving / cutting / both / etc)...

@curtisaitken7027 Жыл бұрын

@@Samcraftcom I think engraving and stencil outline making but not cutting. I’m trying to do some bespoke work and slate engraving. Budget is not really a concern. I am hoping for the roi to cover costs.

@brandiskidmore1163 Жыл бұрын

Is this the 5.5w or the 10w?

@Samcraftcom Жыл бұрын

This is the original 10w.

@charlottependergrass5549 Жыл бұрын

wtg sam

@wb2ire Жыл бұрын

Get a spray can of compressed air that is used for cleaning computer key boards until you can get a compressor.

@debradoucet8847 Жыл бұрын

I miss Angela and the boys!!

@Samcraftcom Жыл бұрын

I understand, but they are not a part of this channel.

@timbertrand632 Жыл бұрын

Your power cord sparks when you plug it into the Ortur.

@Samcraftcom Жыл бұрын

Yep, they all do it with this model. It's even in the user manual! I've never liked that, but after talking with many other users of the machine is "normal"...

@timbertrand632 Жыл бұрын

@@Samcraftcom Thanks for the insight.