Pellet project 2015 Part 1 the burner test

No video

Pellet project 2015 Part 1 the burner test

Рет қаралды 478,384

Күн бұрын

First test of the Pellet Project 2015.
In this part, the burner.
Made of steel profile 40x40x3mm
The blower is a 40x40 PC fan 12volt dc / 50 Ma.
The PC fan can be powered via a zonpaneel. (Option)
This burner is part of a universal as possible
stove.
Obviously with cooking facilities.
The whole must be portable.
Eerste test van het Pellet project 2015.
In dit deel, de brander.
Gemaakt van 40x40x3mm profiel staal.
De blower is een 40x40 Pc-fan 12volt dc/50 Ma.
De Pc-fan kan ook via een zonpaneel gevoed worden.(Optie)
Deze brander gaat deel uitmaken van een zo universeel mogelijke
kachel.
Uiteraard met kook gelegenheid.
Het geheel moet draagbaar worden.

Пікірлер: 53

@jimbelkin7301 5 жыл бұрын

Thank you for all of the measurements and project details. I've been looking for a good pellet stove design to weld up with my everlast welder.

@alwoolhouse6255 4 жыл бұрын

I love your work Bert. I'm going to produce something similar and your designs have really helped me. Bedankt aan de overkant van het water in Engeland.

@BertHeideveld 4 жыл бұрын

Make video.s please

@lastflightofosiris 8 жыл бұрын

The bottom of that T, bottom of where you out the pellets in, try deforming there. Take a hammer, slowly work your way. If you flatten that part just a little bit, you have less cross section for that part, it accelerates the air while coming through that part (the part where the hopper is), that way, no smoke comes out from hopper, and it stays cooler. I hope i can express myself right. If you are familiar with that, i am talking about venturi effect.

@homayounshirazi9550 6 жыл бұрын

Mr. Bert Heideveld, I commend your persistent spirit for design of a more efficient rocket stove. I am certain that after designing 10 or more rocket stoves you will arrive at a design that is optimized in all respects. May I suggest that you adhere to one design and work on primary and secondary air supply portals before changing your basis design elements. Wishing you success.

@carlospenna 9 жыл бұрын

I can only say this: fantastic job!!!

@BertHeideveld 9 жыл бұрын

Thank You. More to come

@FriesinNF 8 жыл бұрын

Fantastisch! Super Idee, sehr gut umgesetzt! Macht richtig Spaß, all Deine Videos zu schauen! Weiter so!

@a231950 9 жыл бұрын

fantastisch....benieuwd voor de evolutie; werk maar snel door want ik zou zo'n pelletrocket willen gebruiken al hopdroger (astje)...

@gaetanproductions 9 жыл бұрын

Good job ! Look forward to seeing part 2

@BertHeideveld 9 жыл бұрын

I need to make the internal grill from thicker steel. And determine the shape. There should be less pellets into the combustion chamber. The supply of them is still too high. I want a slow but so constand as possible fire. Then I can continue with the other parts. It is too cold to work outside. :-(

@gaetanproductions 9 жыл бұрын

Bert Heideveld perhaps you could divide you pellet feeder pipe in two, it could also serve as an air intake (that you could close off if necessary) -10ºC that is cold !

@BertHeideveld 9 жыл бұрын

gaetanproductions Step by step, there is more to come.

@olegt.8912 4 жыл бұрын

Good job, my frend.

@ImprovisedSurvival 6 жыл бұрын

Excellent looking welds.

@SouthpawDavey 9 жыл бұрын

Looking great ;-)

@BertHeideveld 9 жыл бұрын

This is just the beginning.

@SouthpawDavey 9 жыл бұрын

Looking forward to see what its going in ;-)

@insAneTunA 9 жыл бұрын

Hi Bert, I was wondering how this setup works with the original rocket stove shape. I mean the shape with the heat riser. Because basically what you have now is a straight pipe with a feeding hopper on top, and there is no heat riser. The original rocket stove shape has an important function, it draws more air inside the stove, the burn is also more complete. I'm also convinced that the steel is not up to a well functioning and well burning fire, the temperature will exceed the melting point from steel, if it doesn't exceed the melting point from steel then the design is not working properly and it will not burn as efficient as it is meant to be with this rocket stove design. I know that this is an experimental setup, but it seems to me that if the basic design is wrong to begin with then your collected data is not valid either. Anyway, it's always nice to watch these experiments. Peace, iT

@SusanRogersMakingItWork4Me 9 жыл бұрын

Looks like its working good!

@BertHeideveld 9 жыл бұрын

Hello Susan. Yes it works well and reliably. Now I need to design the rest. Sometimes I can not buy steel. I only need small pieces. And there are often not. I am glad that this part is working properly. It is very cold here. And there is a strong wind. Glad I'm back inside. The smell of fresh bread and cake is in the house. Sophia comes straight from school. Who eats a piece of cake. Me too :-)

@SusanRogersMakingItWork4Me 9 жыл бұрын

Bert Heideveld fresh bread and cake, you can't go wrong with that! LOL. Maybe you will find more steel soon and be able to finish this project.

@yashiro798 2 жыл бұрын

400ºC? Nice. Do you think if you increase the air flow ratio, will get a stronger flame? I'm thinking build a burner like this to burn pellet from Açaí, i'ts a native fruit what we have a lot here in Brazil. The burner will heat a reactor for pirolysis.

@BertHeideveld 2 жыл бұрын

If you blow too hard, you will blow the fuel out of the combustion chamber. You have to blow gently for a nice constant flame. Make the burner bigger with a computer fan as a blower on 12 volts. Use square pipe measuring about 11 by 11 cm. Or of the same size as the blower. I burned everything in it, but it was an experiment. Good luck

@yashiro798 2 жыл бұрын

@@BertHeideveld Thanks for you reply. I thinking use 24v blower from A/C of trucks, with speed control. Thanks again.

@BertHeideveld 2 жыл бұрын

@@yashiro798 kzfaq.info/get/bejne/obOHYM1_ndPReJs.html

@19stoney64 9 жыл бұрын

I have watched your videos a long time now. I like this one in size and easy to make. I am interested to see chamber idea. I need to heat my shop building 20 ft x 20ft. I have steel small propane gas tank maybe to use for holding heat with this idea.

@paoluccij 5 жыл бұрын

porque sera que todos los que hacen quemador de pellet casero sacan el fuego lateral, en contra de toda logica y todas las que venden en las tiendas lo hacen hacia arriba, sera que el fuego casero es diferente...

@BertHeideveld 5 жыл бұрын

Això només és un experiment. Salutacions dels Països Baixos

@dave3130 5 жыл бұрын

Brilliant

@BertHeideveld 5 жыл бұрын

Thank you.

@DutchArts1 8 жыл бұрын

Leuke video's bert :o)

@BertHeideveld 8 жыл бұрын

+DutchArts1 Doe m,n best :-)

@bzab334 2 жыл бұрын

How do you do ash clean out and how often?

@esmeraldarevilla1963 6 жыл бұрын

Que materia o que fue lo que le añadiste para esa combustión te agradecería si me pudieras contestar

@sunstreet1000 9 жыл бұрын

OK, we are impressed with this, the 40mm fan is working surprisingly well, do you know its cubic feet per minute rating? Excellent idea for the bolts to hold the fan in place.

@BertHeideveld 9 жыл бұрын

Thanks. I do not know what is the output of the fan. Personally, I assume. That a small overpressure in the inlet channel is enough. I'm not looking for high heat or very hot. Seeking a slow but clean combustion. The final design also get a small chimney. Which can be used optionally. This burner is working properly. I make the internal air holes even better fit.

@creamcrackers279 6 жыл бұрын

woooooooooohooooooo i love your work. How do I get the mini fun like thing to buy?

@markusmeyerink1371 8 жыл бұрын

Mooi brander! Lekker simpel. hoeveel kw doet die? Schatting....? Of hoeveel Kg pellets per uur verbruikt hij?

@lechinoisable 5 жыл бұрын

hi,how about ashes,are they putted out of the tube by the fan?

@BertHeideveld 5 жыл бұрын

Yes.

@HenkK 8 жыл бұрын

ik zit mij al een tijdje af te vragen wat er gebeurt als je deze T verticaal stookt. of te wel, lucht van onder af verticaal aanzuigen, hout van opzij horizontaal toevoegen en vlam/rook ook verticaal omhoog. een verticale in-line rocket stove dus. benieuwd naar de film... groet, Henk.

@BertHeideveld 8 жыл бұрын

Hout of pellets horizontaal aanvoeren is niet handig , nu doet de zwaarte kracht het.

@HenkK 8 жыл бұрын

begrijp ik, kan later altijd weer aangepast worden:). maar brand het beter of heter omdat de toegevoerde lucht de hoek niet om hoeft en dus sneller(?) langs het vuur strijkt...

@denisdb725 5 жыл бұрын

Mooi Engels met een Nederlandse tongval. LOL

@LuckySeven0709 9 жыл бұрын

geweldig Bert, hierdoor heb ik weer wat ideetjes opgedaan, Vraagje , hoelang brand hij op een lading pellets. Ben zelf ook bezig met rocket stove principe, waarbij ik jou idee van pellets ook ga(als mag) gebruiken. filmpje van mijn stove waaraan ondertussen al een paar modificaties zijn gedaan facebook.com/l.php?u=http%3A%2F%2Fyoutu.be%2FDjKsvNh_-us&h=pAQGvGlpX ga zo door, zal zeker regelmatig naar je vorderingen kijken. groet wim van de Veluwe

@BertHeideveld 9 жыл бұрын

Gewoon lekker aan het bouwen gaan Wim. Elk idee wat je ziet en af zelf hebt uitproberen. Zodat je op een gegeven moment die stove hebt die het beste aan jou eisen voldoet. Bijna alles op rocketstove ideeen is al uitgewerkt. het principe is meer dan 200 jaar jong. Pellet project 2015 is domweg van alles uitproberen. Het pellet verbruik is nu nog groot, dit omdat de toevoer nog niet te regelen is. Dat is ook precies waar ik nu mee verder ga. Het gehele kook toestel moet camping gericht zijn. En eventueel ook niet alleen op pellets moeten werken. Zie je