OctoPrint: Control Your 3D Printer Remotely Using a Raspberry Pi!
Рет қаралды 515,388
5 жыл бұрынIn this video, I'll teach you how to install, configure, and use OctoPrint (AKA OctoPi) with your Raspberry Pi, allowing you to control your 3D printer and print things remotely!
---
● Full guide + parts list/links:
howchoo.com/g/y2rhnzm3odz/con...
● What you'll need (direct links to Amazon):
Raspberry Pi 3 Model B+: amzn.to/2QyrIUB
- OR -
Raspberry Pi 4: amzn.to/2v4chfS
Raspberry Pi camera: amzn.to/2D61RO2
Raspberry Pi camera extension cable, 610mm: amzn.to/2ImBHKj
Short mini USB to USB cable: amzn.to/2IjmcD7
MicroSD card, 32GB: amzn.to/2D5a7Or
MicroSD card reader: amzn.to/2Kk0Lod
Raspberry Pi power supply: amzn.to/2MhRVbt
(Optional) XT60 cable used to power my Pi from my Ender 3: howchoo.com/shop/product/xt60...
● NEW! Add a touchscreen to OctoPrint:
• How to Add an OctoPrin...
● Power your Raspberry Pi using your 3D printer's PSU:
howchoo.com/g/zjm0zjnlndq/how...
● Creality Ender 3 Review:
howchoo.com/g/ytbizjaxzjk/cre...
● Using the Ender 3 with OctoPrint (+ Thingiverse models and parts):
howchoo.com/g/ntg5yzg1odk/usi...
● Using the Ender 3 V2 with OctoPrint (+ Thingiverse models and parts):
howchoo.com/octoprint/ender-3...
● Like what we do? Buy us a coffee or beer and support great content!
howchoo.com/donate
● Theme song:
"Microchip" by Jason Farnham from the KZfaq Audio Library.
● Affiliate link/advertising notice:
I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to AMAZON Sites. When you click on an Amazon link above and buy something through Amazon, Amazon may give me a small commission.
@MartianMoon 3 жыл бұрын
Your posture is immaculate
@Howchoo 3 жыл бұрын
Haha thanks!
@RyanKelbel 4 жыл бұрын
Easily the best guide for OctoPrint installation, Thank You. I watched 3 other guides before this and not a single one even mentioned the USB cable or plugging it into the 3D Printer. Thank you for laying out the hardware and requirements beforehand everyone else mentioned the Pi, Camera and SD Card.. that was pretty much it.
@Howchoo 4 жыл бұрын
No problem! I’m really glad it was helpful :)
@drdoctor101 4 жыл бұрын
I agree with ^ . No other guide explains how you physically attach the pi to the printer, incredibly. Thank you for making this video, it helped me get my printer up and running!
@labellesworkshop 5 жыл бұрын
Thank you for this in depth, yet very simple tutorial. I've really wanted to start using OctoPrint on my Ender 5, but I have no prior experience with coding or raspberry pi. I just ordered a pi and camera - looking forward to trying to set it up thanks to your video 😁😁
@Howchoo 5 жыл бұрын
I'm glad it was helpful! Let me know if you run into any issues.
@Howchoo 5 жыл бұрын
Check out the full guide and parts list on howchoo: howchoo.com/g/y2rhnzm3odz/control-your-3d-printer-with-octoprint-and-raspberry-pi Also, check out my new video on adding a touchscreen to OctoPrint! kzfaq.info/get/bejne/bLWAZcZerLeqpWg.html
@ThatGuy-mp9og 5 жыл бұрын
that doesnt show a screen in parts
@Howchoo 5 жыл бұрын
@@ThatGuy-mp9og What do you mean?
@fyremonte 5 жыл бұрын
@@Howchoo I got an Ender 5, I think I need to design a camera holder for use on extruded aluminum
@fyremonte 5 жыл бұрын
It is all there, you have to dive for it.
@Howchoo 5 жыл бұрын
@@fyremonte Thanks -- I'm realizing now I might need to make the parts list more obvious on the site. Do you think it's too hidden/mixed in?
@NaloMeliful 5 жыл бұрын
Very nicely done. Can’t wait to try it out when my RPi3B+ arrives.
@ericilaqua9706 5 жыл бұрын
Thanks very much for the well articulated and professional video! I'm new to 3D and I ended up building a Raspberry Pi box for my Mega-S and it works wonderfully thanks to this video. Thanks for all your insight! Very informative. I have subscribed.
@Howchoo 5 жыл бұрын
Glad you enjoyed it!
@reidt9155 4 жыл бұрын
Just got my octoprint up and running. Thanks for the in-depth tutorial, man. You're awesome
@Howchoo 4 жыл бұрын
Reid T No problem! You’re awesome :) Thanks for watching
@connorkorbin4576 2 жыл бұрын
You prolly dont give a damn but does anybody know of a tool to get back into an instagram account? I was stupid lost my login password. I appreciate any tricks you can give me.
@kameronbryant9796 2 жыл бұрын
@Connor Korbin instablaster =)
@connorkorbin4576 2 жыл бұрын
@Kameron Bryant Thanks so much for your reply. I got to the site through google and im waiting for the hacking stuff atm. Takes quite some time so I will get back to you later with my results.
@connorkorbin4576 2 жыл бұрын
@Kameron Bryant It did the trick and I finally got access to my account again. I am so happy! Thanks so much you saved my ass :D
@floridasaltlife 5 жыл бұрын
thank you so much for doing this guide and such a great job of it as well !!!
@Howchoo 5 жыл бұрын
No problem. Glad you liked it! :) Stay tuned for much more very soon
@TheTinkerDad 5 жыл бұрын
Very nice video, it has exactly all the info I've wanted! Thank you!
@Howchoo 5 жыл бұрын
Glad you enjoyed it!
@hunchojet 4 жыл бұрын
Yooo whats up Zach. I just bought my Ender 3 last week. This is a great tutorial that I'll be trying out tonight thanks to Amazon's same-day delivery. This is also the first video I've watched from you and I'm looking forward to seeing the other 3D printing/Ender 3 vids!
@froot.3638 4 жыл бұрын
Same, I got an ender 5 and even tho I respect his comment on safety my goal is to buy a smoke alarm and jerry rig it into shutting my whole room off or something like that
@GabrielSantos-bm5sl 4 жыл бұрын
Very helpful video. Gave me a good idea of how to use octaprint. Thanks!
@361phil 4 жыл бұрын
very well done video! Thank-you. I appreciated the lesson and like your step-by-step methodology.
@dablet 2 жыл бұрын
that was very comprehensive! thank you for taking the time to make this video
@trippinsage 8 ай бұрын
Thank you, After several attempts this one helped.
@KuyaMagik 2 жыл бұрын
awesome thanks!!
@YASAJTV 3 жыл бұрын
I am using Windows, so special thanks thumbs up for going in detail and explaining both operating systems and that detailed information that big-name YT geeks forget to mention.
@thetekinak 3 жыл бұрын
Best tutorial for setting up RP4 for your 3D printer. Thanks
@djwoske 2 жыл бұрын
thank you for this. Very straight forward and comprehensive.
@davidniblo4616 3 жыл бұрын
Fantastic guide. Thank you!
@GregBabineau 3 жыл бұрын
Great video. Gave me all the answers I was seeking.
@AndrewMcQuillen 4 жыл бұрын
This is great video totally demystifying the process thanks
@Gamex996 5 жыл бұрын
thanks it helped me really fast setup
@SaltyBob355 4 жыл бұрын
Great video. Very thorough.
@RCoryCollins 5 жыл бұрын
Nice video! Thanks for making it. If you thread the camera cable through the slot in the case cover first, you can plug it into the port a little easier than trying to manipulate it through the cover's slot.
@theboilershop1728 2 жыл бұрын
Straight to the point, thank you
@leonhorner1643 Жыл бұрын
Great video, thank you for the instruction.
@ping0518 5 жыл бұрын
Learned so much from your video! THANK YOU!
@3lmo2004 5 жыл бұрын
Legend, nice tutorial!
@Howchoo 5 жыл бұрын
Thanks! :) I‘ll be creating a lot more soon!
@jozin73 5 жыл бұрын
Thanks for the video. Just one note. It would be much more better if you remove video of your self and put a full screen of things you presenting. The thing is when we watch it on the mobile we can't see too much details. Thank you for your work.
@Howchoo 5 жыл бұрын
Thanks for the feedback! I’ll do that next time :)
@transplantx6969 Жыл бұрын
This is a great video and excellently presented. Please don’t tell me I’ve found you too late and you’re no longer making content? 😢 I look forward to watching all your videos anyway but you’re descriptions of the process and your way of instructing is good enough that even I can understand it and follow it (and that’s no mean feat!! Trust me!! 😂 )
@ivangutowski 7 ай бұрын
looks like his last video was 3yrsd ago :(
@steve318k 2 жыл бұрын
Nice video ... lots of helpful information. Still not sure I'm ready to tackle this project, as the further you got into it, the more difficult it started to seem... like rattling off connect with ssh to someone that's never done that or heard of it got mind boggling for me ! never even saw a raspberry pi, so it was all new to me. for the cost of this project, I don't know why it's not offered as an option on printers.
@teddywarner 5 жыл бұрын
Your video does an amazing job explaining everything. Thank you so much. Keep up the good work!
@viciente3945 5 жыл бұрын
.. extremely helpful - thx a lot!
@twiztedmind864 5 жыл бұрын
Thank goodness someone already came up with a way to do this. It is even better that I have the same 3d printer.
@Howchoo 5 жыл бұрын
Glad I could help! I also wrote a guide specifically for using OctoPrint on the Ender 3, should be useful to you if you have the same printer :) howchoo.com/g/ntg5yzg1odk/using-octoprint-with-the-creality-ender-3-3d-printer
@ricardoschenk5113 4 жыл бұрын
Thnx ! for the clear explanation !
@Howchoo 4 жыл бұрын
No problem!
@markr509 4 жыл бұрын
great video, my raspberry pi and camera are on the way from amazon right now
@Howchoo 4 жыл бұрын
Sweet! Post here if you run into any issues and I'll do my best to help you out.
@pottsydog3622 4 жыл бұрын
very helpful - nice and speedy :-)
@queloko24 4 жыл бұрын
Excelent guide man!!!
@Howchoo 4 жыл бұрын
Thanks!
@johnamato5994 4 жыл бұрын
Great job. I subscribed and gave a thumbs up and will order from Amazon thru. Good talent deserves the rewards. I'm 60 years old and my vision is corrected to 15/20. I have a 27" 4k monitor. I could not read the inserts in the video. So please take this as just a little hint. Get your mug off the video, calm the background color, use a bigger font on the inserts, and keep up the good work!
@Howchoo 4 жыл бұрын
Will do for the next one, thanks John!
@SpartyTime 5 жыл бұрын
Awesome tutorial.
@Howchoo 5 жыл бұрын
Glad you liked it!
@iraborton3941 3 жыл бұрын
These instuctions are good and will get it up and running. I was unable to get Octoprint to print as good as printing directly off an SD card plugged into the printer. I tried for over 30 days, got help from numerous forums and KZfaq videos. I finally gave up and just went back to printing from SD card, I still have the webcam just watching the prints, but no control. My printer is an Artillery Sidewinder X1, My Raspberry is a 4 with 8Gb.
@puppylife8708 2 жыл бұрын
Love this!
@sandwich6359 4 жыл бұрын
Thank you so much for you excellent help!!!
@Howchoo 4 жыл бұрын
No problem!
@sandwich6359 4 жыл бұрын
@@Howchoo do you have the video about doing it remotely up yet?
@Howchoo 4 жыл бұрын
Jack Wall No video yet, but I did write this guide about it: howchoo.com/g/mgnmnjg5ywz/how-to-access-octoprint-over-the-internet-from-anywhere-using-octoprint-anywhere
@rty1955 4 жыл бұрын
very helpful thanks
@oohheavygaming9892 4 жыл бұрын
awesome video! definitely going to build this for my ender 5. slightly unrelated question. do you have a video or information on how you made the lighted Howchoo logo sign? I would very much like to build something like that.
@Howchoo 4 жыл бұрын
Yep, I do actually! So for the letters, I just extruded an SVG of each letter to make the 3D-printable models and then made each hollow. For the LEDs, controller, and programming, I used the same approach as in my other guide here: howchoo.com/project/othjmwu4mju/my-led-disco-ball-music-festival-totem -- The approach in that guide is the same, except that I used a flat individually-addressable LED strip (also from Adafruit) rather than the "Christmas tree" styled LEDs shown in that guide.
@pentachronic 3 жыл бұрын
Great video. BTW, screen resolution was a bit low so it's hard to see you screen text etc. Anyway, my main Question: How would you compare this to Repetier ? I'm thinking of migrating to Octopi because Cura is more powerful as a standalone application. However I like the integration of Repetier. Any thoughts ?
@alainsaaiman4975 2 жыл бұрын
I always wanted to know howchoo do this.
@juandemin2930 4 жыл бұрын
great!!! thank you!!!
@Godzillah 4 жыл бұрын
This is great little video I have everything except the long camera cable but I have the short cable. Not many video show how it’s done simple this is very clear Instructions. Question u put octoprint on your raspberry or your computer.
@Howchoo 4 жыл бұрын
Thanks! Per the video, you install OctoPrint on the Pi, not your computer.
@Aidan-tu4un 4 жыл бұрын
4:43 they're called T-Nuts... :-) Great vid, thanks... will be doing this after Xmas...
@Howchoo 4 жыл бұрын
Haha yeah I learned that after publishing this. And no problem! Have fun with it :)
@JohnSmith-mk8hz 4 жыл бұрын
They are actually hammer nuts. For some reason people in the 3d print world mistakenly call them t-nuts. T-nuts are a nut usually used in woodworking.
@conradstanley1027 3 жыл бұрын
Very GOOD!!
@lancelee5757 3 жыл бұрын
great video
@graysonsmith7031 3 жыл бұрын
I'd really like to have this record the time lapse and loop it continuously after the print is don on a smaller screen attached to the printer. Maybe even continuously show a timelapse up to the latest layer while it's printing.
@dafsadfjsadfsakdf435 5 жыл бұрын
what should be " the maximum speed/feedrate of the individual axes and whether their control should be inverted or not." for Creality CR-10S?? and serialport, baudrate settings for cr-10s?
@DavTechCH Ай бұрын
Very Helpful video!!! but was it so hard to maximize the window? :)
@krizzo 4 жыл бұрын
12:57 USB mini is a stronger connection, micro cables tend to end up bending in the vertical if care isn't taken when plugging them in. One of the reasons USB-C is a bit bigger.
@Howchoo 4 жыл бұрын
Very true. Thanks for the info!
@ScouserBerny 4 жыл бұрын
Superb step by step tutorial. Just waiting for my kit to arrive and I'll be building this onto my E3P. Thank you. I have liked and subscribed.
@Howchoo 4 жыл бұрын
Great! Hope you have fun with it :)
@ScouserBerny 4 жыл бұрын
@@Howchoo The kit has arrived and I have begun building it. Some things have changed with the Octopi install since your video but that has not posed a problem so far. I am just wiring the buck into the PSU now. One thing that occured to me, the Raspi being a Linux system needs to be shutdown before being powered off to prevent corruption. This could be a problem if you just turn your printer off. What's your take on this?
@smartassist9700 4 жыл бұрын
Where are your follow up videos? Should show raspberry video of it printing. Also waiting for other installation you mentioned to show completed job and benefits output. Thanks a million. Newbie here.
@camilcia222 4 жыл бұрын
thank you
@Ringwraith19 2 жыл бұрын
Fantastic
@johndavid7840 3 жыл бұрын
Hi Zak, I'm interested in this, is there any instructions to connect this system to Artillery SW X1 v4? Thanks
@ThatGuy-mp9og 5 жыл бұрын
how would i go about adding a display screen
@Howchoo 4 жыл бұрын
I just did a video on that! kzfaq.info/get/bejne/bLWAZcZerLeqpWg.html
@2cool4u24 3 жыл бұрын
Which case did you use for the buck converter. Can you please provide a link.
@christianwilson4066 5 жыл бұрын
each of my 3d printers have their own raspberry octoprint.
@merlinmahmud3316 4 жыл бұрын
Thanks mate for the great video! everything worked purrrfect!! is it somehow possible to enter the octopi surface without being logged in to the same wifi? i want to access octopi while being outside :)
@Howchoo 4 жыл бұрын
Yep! I wrote a separate guide on this: howchoo.com/g/mgnmnjg5ywz/how-to-access-octoprint-over-the-internet-from-anywhere-using-octoprint-anywhere The OctoPrint Anywhere developer is moving this project over to a new one called "The Spaghetti Detective"-I'll update that guide soon with more info on this.
@pahvalrehljkov 5 жыл бұрын
man, you are thorough, nice vid, im gonna sub check your channel...
@Howchoo 5 жыл бұрын
Appreciate it!
@joelhuebner 5 жыл бұрын
Please, if you are pitching an open source product, do not forget your fellow Linux Users. Etcher is available in Linux 32 & 64 bit Systems. Not on ARM system such as Raspberry Pi. It works on my 10yr old HP mini 110 - Atom, running Lubuntu/Debian 9.x
@patrickrobinson317 Жыл бұрын
Great video. 😀 Can Octo print be used for a Laser Printer or a CNC Machine ? If not - is there an alternative that can be used with a raspberry pi ? Thanks.
@willnlisette7861 4 жыл бұрын
This is a great video, very clear and easy to follow for a newbie like me. Would you still recommend the Raspberry Pi 3 Model B+? Or would it be better to start with a 4? If so, could you provide a link?
@willsverges 4 жыл бұрын
There isn't much that needs the extra power of the Pi 4. I'd stick with the cheaper 3 B+ for now.
@Howchoo 4 жыл бұрын
Willverges is correct-the Pi 4 is overkill for this. You can use it if you want; you'll just need to use a different case and cable. This is mentioned in the print guide: howchoo.com/g/y2rhnzm3odz/control-your-3d-printer-with-octoprint-and-raspberry-pi
@CorsairGamer515 3 жыл бұрын
@Howchoo Could I use a USB webcam into the raspberry pi instead of a raspberry pi camera? thanks
@zach1083 4 жыл бұрын
Is it possible to just set up everything minus the camera and go back and add the camera at a later date? I don't have the camera or the flex cable but have the rest.
@danjeln Жыл бұрын
bless you
@tticusRex 4 жыл бұрын
Awesome video! Question, has anyone had any luck adding more than one computer to this type of set up?
@willsverges 4 жыл бұрын
You mean more than 1 printer?
@macmund 4 жыл бұрын
Thanks so much for a great tutorial. Looking for this and it will help a lot on my upgrade. However, I plan to upgrade first my ender 3 board to the silent board which suppose to have thermal runaway activated. Does that mean I can skip the firmware update and hondirectly to pi? Is it the same process with the CR 10 S?
@Howchoo 4 жыл бұрын
No problem! So I definitely recommend the silent board upgrade; the firmware version that it ships with *should* have thermal runaway enabled. I actually just wrote a guide for this: howchoo.com/g/ntmwy2u4owu/ender-3-board-upgrade
@thierrymamin186 2 жыл бұрын
HI, Great video, Thanks... It's possible to have the *stl from the RPI Camera please?? Thank you and nice sunday
@lindamuvic8110 2 жыл бұрын
Wow, youve taken a easily understandable and impliment system, yadda yadda.............and it was bricked.
@cjme1 3 жыл бұрын
Does this work with the Ender 3 Pro? I assume the setup would be the same just with a micro USB instead of a mini
@stevenkenny9270 2 жыл бұрын
I need some help. Following your setup guid on running power from my pro to pi. But I can’t find a usb c cable that has two power cables inside. So you know of any
@justinmiller1886 3 жыл бұрын
what is the application called that he used for the part where he did the file with the wifi?
@gianfrancopaparella9218 3 жыл бұрын
The video is very usefull, but i didn't see and read what windows display. If is it possible to magnify windows with rasp command. Thanks
@bigdogbigben 2 жыл бұрын
Other than watching your prints with the camera and stopping them if something goes wrong, I don't understand why I would want this. I could see using this if there was a way to remove the previous print from the printer. Then you could print something else. What am I missing can you explain ?
@EduardoViruenaSilva Жыл бұрын
You should add OctoLapse plugin.
@DroneFanatic24 4 жыл бұрын
Great video. Easy to follow. I am running into a problem when I try to ssh. It is saying "Could not resolve hostname octopi.local: No such host is known". Any advice?
@Howchoo 4 жыл бұрын
What’s the SSH command you’re running?
@peterjwest 4 жыл бұрын
Great tutorial. I'm making good progress but have hit a bit of a 'bump' trying to print the arm to mount the Pi camera to the gantry. My Ender 3 Pro seems to struggle around the mounting holes for the camera mount despite me doing 0.12mm layer height at a speed of 50mm/s. Do you have any tips to offer in terms of printing those parts please?
@Howchoo 4 жыл бұрын
Sorry I missed this! Is the issue that the arm and camera housing mount (i.e. the hinged portion) are very tightly bound when you put them together? I had this issue as well-this isn't a printing issue, but a design one. There's 0 tolerance between the two parts. I just carefuly cleaned it up and removed a small amount of material using a hobby knife so things would fit together better. Hope this helps!
@pieter-6385 4 жыл бұрын
Hello, thank you for your video. I am wondering though, do I install the latest raspberry pi 4? is it compatible? If not, which model would you advise? Thank you foer your time
@Howchoo 4 жыл бұрын
The Raspberry Pi 4 will work great-check out the linked guide in the video description for a few notes on using the 4.
@BOHICAMAN1 Жыл бұрын
Will these instructions work with a Creality CR-10?
@heatherheinig6047 4 жыл бұрын
Thanks for the video. Octoprint works great! If anyone can help with my issue please respond. After about an hour of printing my computer shows the "This site can't connect screen" and I have lost the ability to reconnect. This does not affect the print, but I can no longer view the camera or any other features. This also means I do not have a good idea of how long the job has left.
@Howchoo 4 жыл бұрын
Whoa that’s very strange. It sounds like it’s probably an issue with your router; the fact that the Pi continues to print tells me it’s still running correctly. Could you try connecting both the Pi and your computer with an Ethernet cable and try again?
@estefaniadesireeavalosrive1056 Жыл бұрын
Hello, I did the buck converter add on and I measure with my multimeter with 5 v and still getting undervoltage warning, I stepped it up to 5.22 and still getting the undervoltage warning, how much can it go up? I want the warning to dissapear
@AugmentedPixel 2 жыл бұрын
Will this be good with the pi4 b 8gb with a m.2 argon case?
@justsomedude4660 5 жыл бұрын
I fried my pi using anet a8 and octoprint.I need to get a new one!
@goinglt3 4 жыл бұрын
will this option work on a Trony x5sa pro?
@NickelCityPixels 4 жыл бұрын
When will you do the step-down converter video?
@Howchoo 4 жыл бұрын
Totally forgot about that one-I added it to my video list :) I have a few other videos I'm working on currently, but soon I'll be releasing a video every week (rather than monthly). Keep an eye out!
@bermchasin 9 ай бұрын
4:50 - T-slot nuts for anyone looking. "channel nuts"
@nameofsomthing1731 3 жыл бұрын
is it possible to do the octopi and a TFT35 E3 V3.0
@pletcgm 6 ай бұрын
Where did you get that screwdriver?
@23demolitionderbyman 2 жыл бұрын
followed everything you did step by step, but whenever i plug my ender 3 micro usb cable into my pi or computer the extruder temperature immediately begins to climb until it maxes out the temperature and shuts down (only has done the max temp shutdown once, b/c i caught it now and unplug the cable before it get too hot) Is there something i've missed or done wrong? tried redoing the whole install several times, even tried the newer 32 bit 4.2.7 board - no changes #plzhelp
@alexandrugroza839 5 жыл бұрын
i want to replace the original melzi creality v1.1.3 ender 3 board that has the input voltage 24v and the mk10 hot end with mainboard mks gen l v1.0 plus tft 2.8 touch screen and titan aero 1.75mm 24v, is this possible ? -on my creality mainboard at ''fans, hot bed, nozzle '' write 12v, but i measure that and i was expected to be 24 but it was 12 v both -so my nozzle theoretical is 24, but it has 12 volts on the mainboard, that is a problem? if i will buy the titan aero hot end what voltage do i have to buy it ? -the melzi mainboard from creality has a ''atmega1284p microproccesor'',but the mks gen l has ''32-bit STM32 microprocessor'' -is that a problem if mks gen l has a 32-bits microprocessor? i mean if it has bore bits that the atmega. Can it burn ? -is the melzi mainboard has theoretica 3* 12 v blocks but in reality 3* 24 volts what voltage need the mks gen l board to have ? if it has 12 volts the al that 3 components to wich need 24 v is going to be any problem ? -that 3 component ''fans, hot end, hot bed '' are in reality 24 volts, the matter if on that mainboard is 12 or 24 volts ?
@mauricedoerr1992 Жыл бұрын
I can't connect to my Aquila PRO. I've been testing with 2 different types of cables, I tried the tape on the 5V I'm not sure what to do.
@shinjimae374 2 жыл бұрын
Would this work for the neptune 2?
@lucbisschops 5 жыл бұрын
Noob question, but do i have to leave my printer on power all the time to controle is, like leave it on. Now after it is done i have a on off button which i turn off, i own a Anet A6 and there is now way i can have my printer in stby mode. Clear video you made, very understandable.👌
@Howchoo 5 жыл бұрын
If the Pi is powered by your printer, you’ll need it to be on so it can continue to power your printer. If you power the Pi separately, you could log into OctoPrint but without the printer being on you couldn’t do anything anyways ;) Does that make sense?
@fabian899 5 жыл бұрын
@@Howchoo is it possible to control a relay wich than powers the printer with the rasperry pi?
@Howchoo 5 жыл бұрын
@@fabian899 Absolutely. Check out this guide and video on controlling a relay using your Pi: howchoo.com/g/m2qwmte5nzk/how-to-use-a-relay-with-a-raspberry-pi
Teaching Tech
Рет қаралды 486 М.
ModBot
Рет қаралды 116 М.
Make With Tech (MakeWithTech)
Рет қаралды 88 М.
Nero3D the Canuck Creator
Рет қаралды 147 М.