I just got this today from Amazon and hardly moving KZfaq channel had this and I had a hard time figuring the sealed small tubes as to where the seal seats. Thanks to him I was able to get it right. I wish I saw this vid earlier too.

Yeah I have the OEM all green version, love the no-spill👍

Always remember to turn the heater on full blast when burping the system.

This will come in handy when I fill up my windshield washer reservoir and wipers

The later versions look identical have a valve fitted to the lower funnel outlet which is really handy to gradually fill, even better it’s got litre graduations on the funnel exterior in 500ml to 2ltrs. Purchased this week at a really low price, already time saved and avoiding Ethelyne Glycol waste is a major heads up for any tool in 2023.

7:36 - The plastic ring is actually for plastic surge tanks. Nice video. Thank you.

I got this for 3800 Series 3 GM engine. The threaded "D" cap and corresponding insert do not fit my standard GM radiator so it's useless. The threads on the cap are different. I ordered it on Amazon part # 87045. The only way I can think of to salvage the unit is to use an old radiator cap and drill a hole in it big enough to pass the yellow fitting through. Just finished working over the old radiator cap. I did it with a 1/4" drill bit to start, and then finished a 1 inch hole with a wood bit because the cap was plastic (the outside). I cut the inside off flush with the bottom of threaded part which released the internal spring and valve assembly. If you do that be careful because it is under tension and can pop out at you if you are not careful. I took a Dremel rotary tool with a steel bit and worked down the plastic to bottom of the o-ring slot so it should be able to get a good purchase on the threads on the radiation fill neck. It was not as bad as I thought as most of the cutting was through plastic.

I saw that it was on sale last month for 9.00 , I bought a pair . it works great

I have this kit but mine also came with a hydrometer for checking the coolant/water mix.

This is good. Do you have a video about burping the engine?

This will come in handy when i replace my lower radiator hose.

just got mine the other day for my 2012 Nissan Frontier. I used the correct fittings and although the fitting that goes into the rad opening seems very tight, it leaks once I pour antifreeze into the funnel. Its leaking at the fitting with the rubber gasket. Any ideas why.

Many videos for this model. None for 87007. Mine has a built in shut off valve in the funnel Iassume it is used in the same manner.

Does it fit on reservoir?

Even thou it’s a copy they all work great

ABD ABD ABD!! A center plug for a funnel? How brilliant is that? 😁👍 Plus, the extensions look as much fun as a small set of Legos! 🎉 Great stuff, man. I especially love the "easy listening" music. Classy. Cheers and God bless! 😁🍻👍

I was trying to burp the system in the 2001 Kia Optima but the water wasn't swirling. I mean, the water didn't seem to be circulating in the engine or radiator. All this time I thought that the reason that the puter was throwing the code was because of air in the system as a result of switching out the radiator. Now, I don't know what to do.

are these available for nissan. i didnt see it listed in your instructions

So I tried this and the coolant got hot an overflowed out of the funnel and went all over the floor. What could I have been doing wrong?

From what I've read, most of these budget kits fit very few vehicles, especially those with the fill cap on the expansion tank.

What vehicles? It didn't work on my Impala. They use it simple radiator s

I noticed all the yellow pieces have corresponding letters, on each one, and the caps are lettered too.

This is my favorite tool I own I swear to God haha. First time I ever did a coolant flush many years back, I got a funnel from my kitchen and wrapped duct tape around it to form a seal on my radiator. Then wondered why there was weird grey gooey muck around the filling hole of the rafiator

I'm thinking of giving this tool a try because I enjoy burping. haha It's been a while since we met up in Vegas. Hope all is well. Thanks Dan for the demo on the funnel!

Why didn't I get one of these 30 years ago.

work on Mercedes? It has expansion tank without Cap on Radiator.

can use it to chug beers too

Same harbor freight 29$

Damn, and I just paid $47 at O'Reilly's.

Note: don’t use household water in your cooling system. You need distilled water. There are minerals in house water that is not good your your system.

How much you make now? What would it take to get you to move to a place with no building codes?.... Outside city limits. And cheapest cost of living in country.$1 gal milk. 1 bed apartments at $500. $13 an hour here same as $33 an HR in Cali. You can grocery shop with a machine gun and only need a machine gun permit. No gun or carry permits needed. Would a 25 year $2 million contract with an additional million dollar retirement and a $5 million bonus opportunity be enough to get your attention?

🍺🍻👌👍👌🍺🍻

the o-rings will fall in your coolant resevoir

U used yes on a simple radiator duh. Try Impala radiator