Oil pan removal and Turbo oil return fitting | Toyota Starlet 4efe turbo build.

No video

Oil pan removal and Turbo oil return fitting | Toyota Starlet 4efe turbo build.

Рет қаралды 3,062

Күн бұрын

How to install a turbo oil drain fitting in a 4efe sump on EP91 Starlets. I also decided to replace the oil pump pickup tube o ring whilst I was in there (same procedure for 4efte / Glanza / Starlet GT turbo). Found a nice surprise for once regarding the crank!
Don't forget to like, comment, share and subscribe!
Instagram: @dan91sgarage
Disclaimer: These videos are meant as entertainment only. They are only a vlog of the work I have carried out on my cars and not meant to be instructional in any way! Working on cars can be dangerous and the results can cause harm to yourself, your vehicle and others! Be careful, be safe and only you are responsible for your actions.
#turbo #glanza #toyotastarlet

Пікірлер: 15

@drewukdrew 9 ай бұрын

Nice one 🙂 Got to do a sump leak on son's GF's glanzia..most helpful vid

@dan91sgarage 9 ай бұрын

Thanks Drew 👍

@antonykhadondi5316 Жыл бұрын

Hi bro I watch each and every day your good job .am looking forward to upgrade my starlet EP91.❤

@dan91sgarage Жыл бұрын

Thanks friend 👍

@dan91sgarage Жыл бұрын

Update: I just compared the crank part numbers on a Toyota parts site. The EP91 4efe and EP91 4efte cranks are the same part number (13401-11061) so should all be 4et cranks used 🙂! The earlier 4efe in the EP82 and 101 corollas use a different part number so this may well be the 4e marked crank.

@mattybyrne6203 Жыл бұрын

Great video Dan keep them coming 👍

@dan91sgarage Жыл бұрын

Thanks Matt, got another one ready for Thursday. 😃

@mattybyrne6203 Жыл бұрын

@@dan91sgarage can't wait dan

@trdja Жыл бұрын

nice video but u should have also remove the pressure relief valve and add a flat washer to shim it , that basically add 15 to 20 psi of oil pressure back to the engine . remember that the turbo oil feed is letting off a about 10 psi of oil pressure .

@dan91sgarage Жыл бұрын

I've checked the Toyota part numbers and both 4efe and 4efte engines use the same oil pressure relief valve. Part number: 15310-10010. Plenty of people run turbos without shimming. I understand where your coming from and each to their own.

@djfrankieflowers 8 ай бұрын

My 4efe oil pickup strainer in rectangular. The fte should be circular as yours. Can I use the rectangular one on the fte engine?

@dan91sgarage 8 ай бұрын

Don't know Frankie. My oil strainer is oblong shaped (2 x straight sides, 2 x half round ends) From the photos / diagrams I can find the 4efte EP91 should have a metal plate attached between the 3 legs. I believe this may act as a baffle to help keep oil in the sump. The EP91 4efe doesn't have this plate. Also the EP82 oil pickup and sump are shallower than EP91.

@klejnotnilu4975 Жыл бұрын

What torque to tight up oil pan?

@dan91sgarage Жыл бұрын

8Nm

@morrisoo543 Жыл бұрын

Hey, i have a question im building my a avensis turbo in my starlet and i heard u talk About the camshaft, i have the 4ete engine do i have the stronger camshaft, it would save my a lot of time instead of taking the oilpan 😂😂