I have a concern with that replacement rotor you’ve put into it - it has a centrifugal fan impeller on it which is the wrong configuration for the vent in the bottom of that router, the original “Makita” rotor (that you found had a short in its commutator) has the “correct” axle fan on it for the position of the vent. - repair the “original” rotor/try to swap the impellers over for the correct air-flow to cool the motor ✅. In its current form, a risk of it overheating ⚠️

No, with black plastic, this is not Makita. ;) There are nagging, but overall a good job.

Now you can do a video on repairing the defective old armature. They do sell commutators for that armature. Just a thought!.

I have two kids that are 2 and 4. After they have ran me ragged.... These videos are my peace. Thank you and keep up the good work

Подшипники надо менять.

Interesting piece of work, like the upgrade, seems to really made a difference. 👍😁🇨🇱🇺🇸

Fel färg på handtaget annars helt ok

The fan on that new rotor won't be functional in that case... This things asking to overheat.

Excellent but little known router, cool project and excellent restoration buddy 👍

You need some Japanese Industrial Screwdrivers (JIS).

Good job. But I didn't like you that changed the colour. Because makita should have a specific blue color.

Good work

I think replacing the cooling fan shouldn't be useless

Комментарий в поддержку канала и ролика, а также труда мастера.

This saved me pulling mine apart, thanks.

Excellent friend, have a nice day !!!.

Good one, nice and decent color selection.

Very nice job 👍 there will be no stopping you now. You will be finding all sorts of jobs to use it for.

I thought you would rewind the armature. That's a great challenge to you for a future project. Nevertheless, nice job! Congrets!

Nicely done 👍👍👍Thanks for sharing

That's some good work. Nicely done !

You should have cut out the shape of the thumbs up button. The wood piece you had was perfect for it.

dont solder the wires because under load the solder can melt again and so i could cause wire burning or something else next time crimp thw wires only

Mejor que nuevo , excelente , saludos desde Venezuela ciudad de Maracaibo.

I have exact same model. Bought almost new condition from local Sunday market for $10.

Really good work. Well done.

Nicely done.

Nice work on the guts. Questionable design choices. 🤔

Лучший!!! Спасибо за потраченное время!!!

black handle on the Makita? not canon !!!

Nicely done... thanks!

Hola, muy bueno, que es lo que usas en el minuto 10:00. Pintura, barniz...??

El cambio del rotor afectará a largo plazo el funcionamiento?

Looks great! 🧡

На ручку посмотрел думаю что за електрокружка)) а нет фрезер

Цвет много значит в этом инструменте

Great result 👏 👍

That cut you made at the end, freehand - very very dangerous. You don’t want to make cuts like that without straight edge guide. Routers climb, and when they start climbing they climb fast

super tare

What are you brushing on at 9:57?

Oh, that's old router? So what WiFi name it has?

what is that white powder you put in warm water? some kind of detergent?

Do you know if the body was cast from a magnesium alloy or something else?

Dude, spectacular video. It was excellent my friend. I'm already your subscriber. Like for everything.

Painting it blk isn't restoring it. It's altering it

wish you didnt paint away the makita colors, now looks like shit

The slats at anchor are already falling off: the anchor is to be replaced. Ламели на якоре уже отваливаются, якорь под замену.

Muito bom 👏👏

hola el video está muy bueno: 🤜🤛👍👏👊

a bit too much use of the hammer and impact screwdriver

what year is that router from?

Show 👏👏🇧🇷

Why on earth would you make your test cuts on PARTICLE BOARD ??????? Next time try it on a real wooden board !!

Да. В чёрном цвете, это уже не makita

Sound like a vaccum cleaners

should have changed / kept the old vent..

That's a weird looking Network device!

Next time just tape over the parts you don't want painted (eg. th outside that fits in the handle.

you cant black a makita wtf

🇪🇨👍

👍

Horrible quedó pq tienen la costumbre de pintar las máquinas cuando son de aluminio xd lo arruinan no se pinta lo aluminio tiene que quedar pulido y laqueada y los plásticos de color Makita también tiene que quedar del mismo color xd de última quedé laqueada lo único que se puede pintar es la marca sea Makita del mismo color que ellos se identifican xd por eso cada marca tiene su color xd una hermosa maquina arruinada y pésima restauración xd

3:20 Unbelievable! You should have not cut all that material from the commutator!